MERCEDES BENZ ACTROS, ATEGO ,AXOR TRUCK FULL FAULT CODES LIST MERCEDS TRUCK FAULT CODE LIST BRAKING SYSTEM CONTROL UNIT (BS) 0160 Communication between the data on the CAN bus of the car has a fault 0162 Speed signal via the CAN bus from the tachograph has a fault 0163 Short circuit or open circuit CAN cable 0166 signal via the CAN bus from the traffic control NR control unit is missing or malfunction 0167 CAN bus signal from the motion control unit GS controller is missing or malfunction 0168 signal via t
1094 Different size tires on the car 1102 Undervoltage or faulty contact in the terminal 30a 1103 Terminal 30a is open 1202 Undervoltage or faulty contact in the terminal 30b 1203 Terminal 30b is open 1302 Undervoltage or faulty contact in the terminal 15 1404 power sensor voltage cable "24V" is a short to ground 1405 power sensor voltage cable "24V" has short to positive 1505 BS unit management has short to positive output X2 15/7 OR Power cable voltage modulator axle load has short to positive 1604 BS uni
022 ABS solenoid valve at right front axle has a short circuit to positive at pin 3 3023 ABS solenoid valve at right front axle has an open on pin 2 3026 ABS solenoid valve at right front axle has broken on track 1 3027 ABS solenoid valve at right front axle has a short to ground on pin 1 3028 ABS solenoid valve at right front axle has short to positive on track 1 3029 ABS solenoid valve at right front axle has a third-party agitation 3120 ABS solenoid valve at left front axle has broken on track 3 3121 AB
142 Speed sensor at left front axle has Short to Plus 4144 Speed sensor at left front axle has interturn fault 4145 The pole wheel on the front axle on the left has a defect 4146 Speed sensor at left front axle provides noise (crackling) 4147 The pole wheel on the front axle left reeling in the persistent location 4148 Speed sensor at left front axle has an air gap 4149 wheel speed on the speed sensor "Front axle left" not credible 4240 Speed sensor at right rear axle has broken 4241 Speed sensor at right
205 wear sensor supply cable brake pads on the front axle has short to positive 5342 Wear indicators for brake pads of the rear axle on the right has short to positive 5343 Wear indicators for brake pads of the rear axle on the right there is no signal 5442 Wear indicators for brake pads on the left rear axle has Short to Plus 5443 Wear indicators for brake pads on the rear axle left no signal 5504 wear sensor power cable, brake pad on the rear axle is a short to ground 5506 wear sensor power cable, brake
7314 Modulator axial loads produces unreliable data 7364 Data transmission via CAN bus braking system has a fault 7365 Data transfer between the modulator and electronics FDR has a fault 7392 Modulator axial loads: Signal equalization includes a fault 7395 Modulator axial loads: auxiliary pressure regulator 7500 trailer control valve is faulty 7512 trailer control valve incorrectly parameterized 7596 trailer control valve has a pressure setting invalid 7604 trailer control valve has a short to ground in the
9543 The sensor rotation angle of the steering wheel does not produce any of the measured parameters 9550 sensor steering angle gives incorrect data 9563 Communication between modules for CAN buses brake system has a fault 9565 Communication between modules for CAN buses brake system has a fault MERCEDES TRUCK FAULT CODE LIST AUTOMATICALLY SELECT THE TRANSMISSION CONTROL UNIT (AG) 0097 Low voltage at terminal 30 0098 Internal fault in the control unit 0099 High voltage at terminal 30 1083 Inadequate transm
2336 Fault in system traffic control FR 2349 Fault in system traffic control FR 2369 Fault in system traffic control FR 2379 CAN bus from the control unit FR has an error or malfunction 2409 Fault in system traffic control FR 2428 Fault in system traffic control FR 2449 Fault in system traffic control FR 2478 Fault in system traffic control FR 2479 CAN bus from the control unit FR has an error or malfunction 2500 Faulty switching control system GS gear 2502 Faulty switching control system GS gear 2504 Fault
2968 Fault in system traffic control FR 2979 CAN bus from the control unit FR has an error or malfunction 3008 Fault in system traffic control FR 3010 Fault in system traffic control FR 3028 Fault in system traffic control FR 3079 CAN bus from the control unit FR has an error or malfunction 3120 Faulty RS retarder control system 3138 Faulty RS retarder control system 3179 CAN bus from the RS control unit has an error or malfunction 3280 data from the vehicle control unit INS changed or Error in communicatio
0168 Bus IES-CAN: Signal "Supply voltage, Information Bit» absent (INS) OR Bus IES-CAN: control unit FMR has an error and the lack of reliability of the signal OR Bus IES-CAN: control unit FR has an error and the lack of reliability of the signal 0169 Bus IES-CAN: Recognition of the curves is not possible 0170 Bus IES-CAN: The setpoint in the braking system is not 0171 Bus IES-CAN: Recognition of the curves is not possible 1010 control unit: internal error 1012 control unit: checksum specific ECU data 1013
3020 Solenoid valve 3/2 content: open 3021 Solenoid valve 3/2 content: short to ground 3022 Solenoid valve 3/2 content: short to positive 3120 Solenoid valve 2/2 drive axle left: open 3121 Solenoid valve 2/2 drive axle left: short to ground 3122 Solenoid valve 2/2 drive axle left: short to positive 3220 Solenoid valve 2/2 drive axle on the right: open 3221 Solenoid valve 2/2 drive axle on the right: a short to ground 3222 Solenoid valve 2/2 drive axle on the right: Short to Plus 3320 Solenoid valve 3/3 drop
4242 move the front axle sensor: short circuit to plus 4243 Sensor move the front axle: Fault nominal coil resistance 5040 pressure sensor axle Left: open 5041 pressure sensor axle left: short to ground 5042 pressure sensor axle left: short to positive 5140 pressure sensor axle right: open 5141 pressure sensor axle right: short to ground 5142 pressure sensor axle right: short to positive 5240 Pressure Sensor front axle: open 5241 Pressure Sensor front axle: short to ground 5242 Pressure Sensor front axle: S
6321 Contact Us WR valve has a short to ground 6322 Contact Us WR valve has short to positive MERCEDES TRUCK UNIT FAULT CODES LIST OF TRAFFIC CONTROL MANAGEMENT SYSTEM (FR 0110 - CAN message from control unit ABS anti-lock system is missing or incorrect. 0111 - GS control unit measured value is invalid. 0112 - CAN message from the control unit is missing or incorrect. 0113 - CAN message from control unit RS governance of the retarder is missing or incorrect.
1125 - Jack 'D +' to contact X4 18/13 is invalid or has a circuit break or short circuit to ground. 1223 - Switch clutch pedal 1 to 18/1 contact X1 is a circuit break or improperly collimated. 1421 - Brake Light Switch is a circuit break or improperly collimated. 1423 - Brake light switch on the contact H118 / 11 has a circuit. 1523 - faulty cruise control switch-temposet. 1524 - faulty cruise control switch-temposet. 1526 - Sign 'Quit' cruise control switch is open.
3233 - Faulty sensor monitoring of the air filter. 3236 - reached the boundary of contamination of the air filter. 3330 - Ambient temperature sensor has a circuit break / short to positive / weight 3430 - The clutch stroke is a circuit break, short to ground or short to positive. 3533 - Faulty coolant level sensor. 3634 - Reached max wear clutch facings. 3635 - moving the clutch sensor out of range 4141 - Signal "Input speed KGT unreliable.
5354 - Solenoid valve 'the Split 1' has a discontinuity circuits. 5452 - Solenoid valve 'the Split 2' has a short to ground. 5453 - Solenoid valve 'the Split 2' has the circuit to positive. 5454 - Solenoid valve 'the Split 2' has a discontinuity circuits. 5552 - The total weight of the wire of the solenoid valves Y29 and Y30 is a short to ground. 5553 - The total weight of the wire of the solenoid valves Y29 and Y30 have circuit to positive.
0110 CAN bus from the ABS control unit is missing or has a fault 0111 CAN bus from the GS control unit is missing or has a fault OR Measured value of the GS of the control unit is not valid 0112 CAN bus control unit of the KS is missing or has a fault 0113 CAN bus from the RS control unit is missing or has a fault 0114 CAN bus from the INS control unit is missing or has a fault 0115 CAN bus from the PSM control unit is missing or has a fault 0116 CAN bus vehicle has a defect open / short circuit to ground /
weight OR D + connector X4 18/13 invalid value / open / short circuit to ground 1223 Switch clutch pedal 1 to 18/1 contact X1 is open or incorrectly carried out adjustment OR Switch clutch pedal X1 18/1, open / incorrectly carried out adjustment 1323 Switch handbrake 15/9 X3 has a fault or short circuit 1421 The switch of stoplights is open or incorrectly carried out adjustment OR The switch of stoplights, open / incorrectly carried out adjustment 1423 The switch of stoplights at the contact X1 18/11 has a
OR Square-wave output GSV 1 instruction cycle management of a switch, a short circuit in the weight 2220 square-wave output GSV 2 cycle-accurate control of a switch, a short circuit in the a plus 2222 square-wave output GSV 2 cycle-accurate control of a switch, a short circuit in the weight 2320 square-wave output GSV 3 cycle-accurate control of a switch, a short circuit in the a plus 2322 square-wave output GSV 3 cycle-accurate control of a switch, a short circuit in the weight 2420 square-wave output GSV
3233 air filter contamination sensor defective 3236 reached the boundary of contamination of the air filter 3330 Outside temperature sensor open / short to positive / short circuit to ground 3430 displacement transducer coupling is open / short circuit to positive / short circuit to ground 3533 coolant level sensor is faulty 3634 reached the maximum wear of clutch facings 3635 displacement transducer coupling is allowed by setting boundaries 4041 Terminal signal W has a fault / open / short circuit to groun
5153 The output X3 15/7 has short to positive 5154 The output X3 is open 15/7 5252 Connecting MBA engine brake output valve signal, short to ground 5253 total cable weight of the magnetic valve "engine brake" is short to positive 5351 output signal X4 X4 18/7 or 18/8 is an open or short to positive 5352 Solenoid valve divider 1 has a short to ground 5353 Solenoid valve divider 1 has a short circuit to positive 5354 Solenoid valve divider 1 is open 5451 output signal X4 X4 18/7 or 18/10 is open or short circ
5954 Office of the automatic topping up engine oil has broken 6161 control unit has an internal error The control unit 6262 has an internal fault 7060 parameterization error or internal fault "Basic setting at idle speed move more than limit the operating speed the vehicle is stationary " OR Parameterization error or internal error 15 "internal parameter Brake Control Long-acting is not valid " OR Parameterization error or internal error "Internal parameter Maximum torque inhibition of long-acting output ge
OR parameterization error or internal error "gear ratio divider is programmed with mistake " OR parameterization error or internal error 24 "gear ratio divider is programmed a mistake " MERCEDES TRUCK LIST OF SPECIAL MODULE CONTROL UNIT FAULT CODES WITH PARAMETER SETTING (PSM) 0160 Communication fault on the CAN bus vehicle 0161 Error communication with the ABS control unit or BS 0162 Error communication with the control unit FR 0163 Error communication with the control unit FR 0164 Failed to communicate w
1011 EEPROM-error OR Internal fault in the control unit 1012 parameterization error in the control unit 1100 High voltage at terminal 30 1101 Undervoltage at terminal 30 1102 Open voltage supply terminal 30 OR Inadequate voltage at terminal 30 1200 High voltage at terminal 15 1201 Undervoltage at terminal 15 1202 Undervoltage at terminal 15 1210 Broken wire on terminal 15 2020 Output "engine running a generator in order" (Contact X4 18/9) has a short circuit to ground OR Digital output 1 is shorted to groun
Digital output 3 has a short to ground 2221 Output "Management clutch lock cylinder" (18/11 Contact X4) has a short circuit to positive or open circuit OR Digital output 3 has a short circuit to positive or open circuit 2222 Unreliable excitation of the solenoid valve at the digital output 3 2320 Output "Management clutch valve" (18/12 Contact X4) has a short short to ground OR Digital output 4 has a short circuit to ground 2321 Output "Management clutch valve" (18/12 Contact X4) has a short circuit to posi
21 The output of the "neutral position" (18/15 Contact X4) has a short circuit to positive or breakage 2720 Output "PTO Management 1" (18/16 Contact X4) has a short to weight 2721 Output "PTO Management 1" (18/16 Contact X4) has a short to plus or breakage 2722 Lack PTO feedback 1 (X3 Contact 15/7), despite the presence of excitation Power take-off 1 (Contact X4 18/16) 2723 Lack of excitation power take-off 1 (Contact X4 18/16), despite the presence of feedback Power take-off 1 (X3 Contact 15/7) 2820 Outp
PTO 3 (X3 Contact 15/9) 3020 Output "engine speed signal" is a short to ground OR The output of the "Reverse gear included" (Contact X4 18/9) has a short to weight The output 3021 "of the engine speed signal" has a short circuit to positive OR The output of the "Reverse gear included" (Contact X4 18/9) has a short circuit to positive or open 3120 Output signal "Transmission enabled 1" (18/10 Contact X4) is shorted to ground OR The output signal "velocity signal" is shorted to ground 3121 Output signal "Tran
3520 Output signal "Gear 2 included" (18/14 Contact X4) is shorted to ground 3521 Output signal "Gear 2 included" (18/14 Contact X4) has a short circuit to positive or breakage 4020 Output signal Contact X4 18/9 is a short to ground 4021 Output signal Contact X4 18/9 has short to positive or open circuit 4040 manual wire gas sensor is broken 4041 manual wire gas sensor signal is shorted to ground 4042 manual wire gas sensor has short to positive 4043 Short circuit between the signal wire and the wire feed p
MERCEDES TRUCK UNIT FAULT CODE LIST MANAGEMENT TACHOGRAPH (DTCO) 0004 Open voltage supply cable 1000 CAN error 10000 Positioning drive tachograms violated 1100 CAN error Internal Error 1200 1400 Calibration of the tachograph contains fault 1500 Fault Management details 1600 Fault Management details 1704 Connection CAN c dashboard INS is not properly 3408 Speed Sensor Malfunction 3504 Speed Sensor Malfunction 4804 output speed fault 8000 movement without drive tachograms 8100 Drive tachograms first driver mi
0104 Block of work after an unsuccessful launch 0200 flame interruption occurs again 0301 Overvoltage 0302 Undervoltage 0400 Premature flame recognition 0501 Flame sensor short circuit 0502 Open in a flame sensor circuit 0601 Short circuit Temperature sensor 0602 Break in the temperature sensor circuit 0701 Short metering pump 0702 Open circuit dosing pump 0801 Short-circuit the fan motor 0802 Open in a fan motor circuit 0803 Wrong fan motor speed 0901 Short glow plug 0902 Open circuit glow plug 1000 Overhe
1702 Fan excitement to switch water circuit is open MERCEDES TRUCK LIST OF BLOCK ERROR CODES WS (MAINTENANCE SYSTEM) 0122 - CAN bus Overload 0123 - Functional CAN bus failure 0132 - Data WS control unit lifecycle wrong. 0133 - WS control unit parameters are incorrect.
0402 - exceeded range of front axle temperature sensor measurements. 0405 - The measured value of the front axle unreliable temperature sensor. 0410 - exceeded the maximum allowable temperature of the oil front differential. 0501 - rear axle temperature sensor has a fault "Short circuit to ground." 0502 - exceeded the range of the rear axle temperature sensor measurements. 0505 - The measured value of the rear axle unreliable temperature sensor.
1502 - The measured value of brake pad wear 1st front axle on the right above the measuring range. 1503 - The measured value of brake pad wear 1st front axle on the right below the measurement range. 1504 - Open the right signal wire sensor Brake pad wear 1st front axle. 1505 - invalid measurement value of brake pad wear 1st front axle on the right. 1520 - Failure of the CAN signal Brake pad wear 1, Front Axle Right 1601 - The closure of the signal line of the left sensor Brake pad wear 2nd front axle.
1901 - The closure of the signal line of the right sensor Brake pad wear 1 st rear axle. 1902 - The measured value of brake pad wear 1st rear axle on the right above the measuring range. 1903 - The measured value of brake pad wear 1st rear axle on the right below the measurement range. 1904 - Open the right signal wire sensor Brake pad wear 1 st rear axle. 1905 - invalid measurement value of brake pad wear 1st rear axle right.
20 - Failure of the CAN signal measured value air filter is clogged 4105 - invalid measurement of oil temperature in the retarder brake (retarder). 4110 - exceeded the maximum allowable temperature of the oil in the retarder brake (retarder). 4120 - Failure of the CAN signal is the measured value of oil temperature in the retarder brake (retarder) 5105 - invalid measurement value of the oil temperature in the engine. 5110 - exceeded the maximum allowable temperature of the oil in the engine.
1010 Internal error in the control unit 1011 Unreliable data harmonization 1012 GS (EPS) control unit is not correctly parameterized 1080 TEST-TEST-OR Electronics Software TEST-1081 Computer software 1082 module verification stand zaaktivirovan 1101 Overvoltage at terminal 30 1102 Undervoltage at terminal 30 1201 mass cable for the control unit is open 1301 Overvoltage at terminal 15 1302 Undervoltage at terminal 15 1503 Supply voltage for the joystick is broken 1504 Supply voltage for the joystick has a sh
Error 2035 lifting the ban on the inclusion of an emergency electronics 2036 Switch emergency operation has failed 2037 The final stage includes a feedback fault GS 3020 block valves (EPS), MS1 solenoid valve is open GS 3021 block valves (EPS), MS2 solenoid valve is open 3022 Valve GS (EPS), the solenoid valve MS1 has a short to ground 3023 Valve GS (EPS), the solenoid valve MS2 has a short to ground 3024 Valve GS (EPS), the solenoid valve MS1 has short to positive 3025 Valve GS (EPS), the solenoid valve MS
3424 Valve GS (EPS), the solenoid valve MR1 has short to positive 3425 Valve GS (EPS), the solenoid valve MR2 has short to positive 3803 total cable weight of the magnetic valve is open 3804 total cable weight of the magnetic valve has a short to ground 3805 total cable weight of the magnetic valve has a short circuit to positive 4040 divider probe is broken 4041 divider sensor has a short circuit to ground 4042 divider sensor has short to positive 4043 divider functioning Faulty sensor components 4044 Comp
5040 signal from the angle sensor B57 missing Error 5043 B57 component operation OR Error angle sensor operation 5140 B3 speed sensor for the intermediate shaft has broken OR The signal from the rotation sensor B3 is absent 5141 B3 speed sensor for the intermediate shaft is a short to ground 5142 B3 speed sensor for the intermediate shaft has a short circuit to positive OR B3 speed sensor for the intermediate shaft has an open or short to positive 5143 operation failed speed sensor component for the interme
0102 Sensor supply "filling pressure in the circuit 1 'has a short circuit to positive 0104 Sensor input signal "pressure filling circuit 1 'does not reach the measuring area 0105 Sensor input signal "pressure filling in the loop 1" is greater than the measurement area 0201 Power Sensor "Filling pressure in circuit 2" is a short to ground 0202 Power Sensor "Filling pressure in circuit 2" has short to positive 0204 Sensor input signal "Filling pressure in circuit 2" does not reach the measuring area 0205 Sen
1107 Status of digital input H1.18 / 7 «Differential lock 2.Zadney axis" unreliable 1108 Status of digital input H1.18 / 8 "rear interaxle lock" unreliable 1109 Digital input H1.18 / 9 invalid OR Digital input status H1.18 / 9 "Locking the driver's cab on the right" unreliable 1110 Digital input H1.18 / 10 invalid 1111 Status of digital input H1.18 / 11 "PTO" unreliable 1112 Digital input H1.18 / 12 invalid 1113 Status of digital input H1.18 / 13 "Control lamps" unreliable 1114 Status of digital input H1.
1421 parameterization error in the control unit OR Parameterization error in the n-module 1432 Internal error in the control unit OR n-module is faulty 1520 CAN bus to the tachograph is faulty OR V-signal from the control unit FR offline 1903 Terminal 15 is open 1941 Overvoltage OR Over voltage at terminal 15 1942 Undervoltage at terminal 15 2001 Communication on the exchange of data with the address control unit 1 is broken 2002 Communication on the exchange of data with the control unit FR broken 2003 Com
2016 Communication on the exchange of data with the address 16, the control unit is broken 2017 Communication on the exchange of data with the control unit NR broken 2018 Communication on the exchange of data with the FFB control unit is broken 2019 Communication on the exchange of data with a ZV or KSA control unit is broken 2020 Communication on the exchange of data with the EKL control unit is broken 2021 Communication on the exchange of data with the address 21, the control unit is broken 2022 Communica
2039 Communication on the exchange of data with the address 39 of the control unit is broken 2040 Communication on the exchange of data with the MR control unit is broken 2041 Communication on the exchange of data with the address 41 of the control unit is broken 2042 Communication on the exchange of data with the SRS control unit is broken 2043 Communication on the exchange of data with the address 43 control unit is broken 2044 Communication on the exchange of data with the EDW control unit is broken 2045
SPA 3005 control unit defective OR The control unit 5 at defective 3006 PFA control unit defective 3007 Block FLA control defective 3008 GS Control unit defective OR KS control unit defective 3009 GS Control unit defective 3010 control unit at 10 defective 3011 SIR control unit defective SIL 3012 control unit defective 3013 Block WSK control defective 3014 ABS control unit defective 3015 RS control unit defective 3016 to the address control unit 16 is not working properly 3017 NR control unit defective 3018
3037 control unit at 37 defective 3038 block AGE control defective 3039 to the address control unit 39 is not working properly 3040 MR control unit defective 3041 to the address control unit 41 is not working properly 3042 SRS control unit defective 3043 to the address control unit 43 is not working properly EDW 3044 control unit defective 3045 control unit at 45 defective 3046 PSM control unit defective 3047 Block SRB control defective 3048 at 48 control unit defective 3049 ART control unit defective OR Th
4821 Output signal Contact X4 18/17 has short to positive or open circuit 4920 Output signal Contact X4 18/18 has a short to ground 4921 Output signal Contact X4 18/18 has short to positive or open circuit 5020 Output "engine speed signal" (Contact X1 18/4) has a short to weight 5021 Output "engine speed signal" (Contact X1 18/4) has a short to plus or breakage 5080 Protective function for the power take-off are bridged by hand 5120 Output "Speed Signal" (Contact X1 18/5) has a short circuit to ground 5121
6043 hand-held gas sensor power cable (Contact X1 18/10) has a short circuit to positive 6140 Input "Starting the motor" (18/7 Contact X2) has a short circuit to ground 6141 Input "Starting the motor" (18/7 Contact X2) has a short circuit to positive 6240 Input "Engine Stop" (18/8 Contact X2) has a short circuit to ground 6241 Input "Engine Stop" (18/8 Contact X2) has a short circuit to positive 6340 Input Signal "Lock start" (18/9 Contact X2) has a short circuit to ground 6341 Input "immobilizer" (18/9 Con
