CL Operator’s Manual
CL 500 CL 55 AMG CL 600
Our company and staff congratulate you on the purchase of your new Mercedes-Benz. Your selection of our product is a demonstration of your trust in our company name. Further, it exemplifies your desire to own an automobile that will be as easy as possible to operate and provide years of service. Your Mercedes-Benz represents the efforts of many skilled engineers and craftsmen.
Introduction Product information .......................... 7 Operator’s manual ............................. 8 Where to find it ................................ 13 Reporting Safety Defects ................ 15 Instruments and controls Instruments and controls ............... 18 Door control panel ....................... 20 Overhead control panel ............... 21 Dashboard .....................................22 Center console ..............................24 Operation Vehicle keys ......................
Contents 2 Safety guidelines for the seat belt, emergency tensioning retractor and airbag .................................. 100 Infant and child restraint systems ....................... 102 Steering wheel adjustment .......... 105 Rear view mirrors .......................... 106 Rear view mirror, automatic antiglare ................... 106 Memory function ............................111 Instrument cluster ..........................114 Multifunction steering wheel, multifunction display ...............
Coat hooks ...................................... 192 Cup holder ...................................... 193 Ashtrays .......................................... 196 Lighter ............................................. 198 Parcel net in trunk ........................ 199 Cargo tie-down hooks ....................200 Parcel net in front passenger footwell ....................200 Telephone, general ........................201 Garage door opener .......................202 Infrared reflecting windshield ....
Contents 4 Electronic stability program (ESP) — warning lamp ...............295 Distronic (DTR) — warning lamp ..............................295 Seat belt nonusage warning lamp ..............................296 Malfunction and indicator lamp in the center console ......296 AIRBAG OFF indicator lamp .....296 Malfunction and warning messages in the multifunction display ...............297 DISPLAY DEFECTIVE (engine control unit) ..................298 DISPLAY DEFECTIVE (several systems) ......................
Changing wheels ...........................340 Tire inflation pressure ..................345 Battery .............................................346 Jump starting ..................................349 Towing the vehicle .........................351 Exterior lamps ................................354 Headlamp assembly ...................355 Taillamp assemblies ..................358 Standby bulb function ................... 361 Changing batteries in the electronic main key .......
Contents 6 Technical data Index Spare parts service ........................384 Warranty coverage .........................384 Identification labels .......................385 Layout of poly-V-belt drive ............387 Technical data ................................388 Fuels, coolants, lubricants etc. - capacities .......393 Engine oils ......................................395 Engine oil additives .......................395 Air conditioner refrigerant ...........395 Brake fluid .......................
Product information Kindly observe the following in your own best interest: We recommend using Mercedes-Benz original parts as well as conversion parts and accessories explicitly approved by us for your vehicle model. We have tested these parts to determine their reliability, safety and their special suitability for Mercedes-Benz vehicles.
Introduction 8 Operator’s manual This Operator’s Manual contains a great deal of useful information. We urge you to read it carefully and familiarize yourself with the vehicle before driving. For your own safety and longer service life of the vehicle, we urge you to follow the instructions and warnings contained in this manual. Ignoring them could result in damage to the vehicle or personal injury to you or others.
Important notice for California retail buyers of Mercedes-Benz automobiles Under California law you may be entitled to a replacement of your vehicle or a refund of the purchase price, if Mercedes-Benz USA, LLC or its authorized Mercedes-Benz Center fails to conform the vehicle to its express warranties after a reasonable number of repair attempts during the period of one year or 12 000 miles from original delivery of the vehicle.
Introduction 10 Roadside assistance The Mercedes-Benz Roadside Assistance Program provides factory trained technical help in the event of a breakdown. Calls to the toll-free Roadside Assistance number: 1-800-FOR-MERCedes (in the USA) 1-800-387-0100 (in Canada) will be answered by Mercedes-Benz Client Assistance Representatives 24 hours a day, 365 days a year. For additional information refer to the Mercedes-Benz Roadside Assistance Program brochure in your glove box.
Operating your vehicle outside the USA or Canada If you plan to operate your vehicle in foreign countries, please be aware that: • Service facilities or replacement parts may not be readily available, • unleaded gasoline for vehicles with catalytic converters may not be available; the use of leaded fuels will damage the catalysts, • gasoline may have a considerably lower octane rating, and improper fuel can cause engine damage.
Introduction 12 We continuously strive to improve our product, and ask for your understanding that we reserve the right to make changes in design and equipment. Therefore, information, illustrations and descriptions in this Operator’s Manual might differ from your vehicle. Optional equipment is also described in this manual, including operating instructions wherever necessary.
Where to find it The Operator’s Manual is divided into eight sections: • Instruments and controls: An overview of all the controls that can be operated from the driver’s seat. • Operation: Information on the vehicle’s equipment and its operation. • Driving: Important information on driving. • Instrument cluster display: Displays and indicator lamps on the instrument cluster with brief instructions. • Practical hints: Assistance and instructions in the event of an emergency.
Introduction 14 Problems with your vehicle If you should experience a problem with your vehicle, particularly one that you believe may affect its safe operation, we urge you to immediately contact your authorized Mercedes-Benz Center to have the problem diagnosed and corrected if required.
For the USA only: The following text is published as required of manufacturers under Title 49, Code of U.S. Federal Regulations, Part 575 pursuant to the “National Traffic and Motor Vehicle Safety Act of 1966”. Reporting Safety Defects If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Mercedes-Benz USA, LLC.
Instruments and controls Instruments and controls ............... 18 Door control panel ....................... 20 Overhead control panel ............... 21 Dashboard .....................................22 Center console ..............................
Instruments and controls Operation Instrument cluster display Driving Instruments and controls Practical hints 18 Instruments and controls 3 Car care Technical data Index
1 Door control panel, see page 20 3 Dashboard, see page 22 2 Overhead control panel, see page 21 4 Center console, see page 24 Instruments and controls Instruments and controls Operation 19 Driving Instrument cluster display Practical hints Car care Technical data Index
Instruments and controls Operation Instrument cluster display Driving Instruments and controls Practical hints Car care Technical data 20 Door control panel 1 Door handle, pull to open, see page 48 2 Memory function (for storing seat, steering wheel, rear view mirror and exterior mirror settings), see page 111 5 4 2 3 Seat heater, see page 76 Seat ventilation, see page 79 4 Front seat adjustment, see page 67 3 5 Exterior mirror adjustment, see page 107 Exterior mirrors, electrically folding, s
Overhead control panel 1 Interior lighting, see page 184 2 Sliding/pop-up roof, see page 181 3 Tele Aid (emergency call system), see page 210 4 Hands-free microphone for Tele Aid, telephone and voice recognition system 1 5 Rear view mirror, see page 106 6 Garage door opener, see page 202 2 3 4 5 6 P82.
Instruments and controls Operation Instrument cluster display Driving Instruments and controls Practical hints Technical data Car care 22 Dashboard 16 1 17 17 13 14 2 18 11 3 22 23 3 15 5 6 7 18 12 10 4 19 20 21 9 8 P68.
1 Left front parktronic warning indicator, see page 281 13 Instrument cluster, see page 114 2 Side air outlet, adjustable 14 Voice recognition system switch, see separate operating instructions 3 Air volume control for side air outlet 15 Starter switch, see page 222 4 Exterior lamp switch, see page 156 16 Right front parktronic warning indicator, see page 281 5 Headlamp washer button, see page 159 17 Fixed air outlets 6 Parking brake release, see page 238 18 Center air outlets, adjustable 7 Hood
Instruments and controls Operation Instruments and controls Center console Driving Instrument cluster display Practical hints Car care Technical data 24 1 ESP (electronic stability program) control switch, see page 273 2 Level control, see page 276 3 ABC (active body control), see page 275 4 Rear seat head restraints, automatic, see page 81 5 Hazard warning flasher switch, see page 163 6 Central locking switch, see page 50 7 Antitheft alarm system, see page 62 Switch for tow-away alarm, see page 64
12 Ashtray, see page 196 Lighter, see page 198 15 AIRBAG OFF indicator lamp, see page 296 16 Distronic (DTR) – switch for distance notification function, see page 265 13 Start-/Stop button Starter switch for KEYLESS-GO only, see page 224 17 Distronic (DTR) – thumbwheel for setting distance, see page 265 14 Automatic transmission, see page 229 Instruments and controls Instruments and controls Operation 25 Driving Instrument cluster display Practical hints Car care Technical data Index
Instruments and controls Operation Driving Contents - Operation Operation Vehicle keys ...................................... 28 Start lock-out ....................................32 General notes on the central locking system ...............33 Central locking system ................... 34 Radio frequency and infrared remote control ..............................34 KEYLESS-GO ................................. 38 Opening and closing windows and sliding/pop-up roof from outside ...........................
CD player .....................................126 Cassette player ...........................127 Telephone ........................................ 128 Telephone book .......................... 128 Redialing ..................................... 130 Incoming call .............................. 131 Navigation system .......................... 132 Distronic (DTR) ............................... 133 Trip computer ................................. 134 Malfunction/warning message memory ......................
Instruments and controls Operation Driving Instrument cluster display Central locking system Practical hints Car care Technical data 28 Vehicle keys and KEYLESS-GO-cards (optional) Warning! Included with your vehicle are: When leaving the vehicle always remove the electronic key from the starter switch and take the KEYLESS-GO-card (if so equipped) with you, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle.
Electronic main key When using the mechanical key (2) for lock operations, it can be removed by sliding it out of the remote control. To do so, move locking tab (3) to the right and slide the mechanical key (2) in direction of arrow (4). The remote control transmitter is located in the electronic main key. 1 The infrared receivers are located in the door handles. Note: Remove the mechanical key from the electronic main key when using valet parking service.
Instruments and controls Operation Driving Instrument cluster display Central locking system Practical hints Car care Technical data 30 Electronic reserve key The electronic reserve key (1) works only in the starter switch. There are no batteries inside the electronic reserve key. The mechanical key (2) works only in the driver’s door, trunk, and storage compartment locks. 1 To use the mechanical key (2), remove it from its electronic reserve key (1). Note: P80.
KEYLESS-GO-card The validity of the KEYLESS-GO-card is checked every time when grasping a door handle or pushing the trunk lid release. Once the KEYLESS-GO-card is recognized outside the vehicle, the doors, trunk lid and fuel filler flap are unlocked, depending on the selected mode (global or selective unlocking mode, see page 43). Starter switch KEYLESS-GO, see page 224. 1 Starting and turning off the engine with KEYLESS-GO, see page 227 and page 228.
Instruments and controls Operation Driving Instrument cluster display Central locking system Start lock-out Important! Operating with electronic key: Removing the electronic key from the starter switch activates the start lock-out. The engine cannot be started. Inserting the electronic key in the starter switch deactivates the start lock-out. Operating with KEYLESS-GO: Turning off the engine with the start-/stop button on the gear selector lever activates the start lock-out.
General notes on the central locking system Note: If the electronic key is inserted in the starter switch, the vehicle cannot be locked or unlocked with the remote control. If neither the remote control nor KEYLESS-GO system functions, use the mechanical key to unlock or lock the vehicle. To start engine, insert the electronic key in the starter switch. There could be a slight delay until the electronic key can be turned in the starter switch.
Instruments and controls Operation Driving Instrument cluster display Central locking system Practical hints Technical data Car care 34 Central locking system 4 Radio frequency and infrared remote control 3 The electronic main key has an integrated radio frequency and infrared remote control. 2 1 Due to the extended operational range of the remote control, it could be possible to unintentionally lock or unlock the vehicle by pressing the transmit button.
6 Infrared receiver in driver’s door handle Central locking system Instruments and controls Operation 7 Infrared receiver in passenger door handle 35 Driving Instrument cluster display Practical hints Car care Technical data Index
Instruments and controls Operation Driving Instrument cluster display Central locking system Locking and unlocking with remote control Unlocking: Press transmit button Œ. All turn signal lamps blink once to indicate that the vehicle is unlocked. The remote control can be programmed for two kinds of unlocking modes (see below): Selective unlocking mode – Press transmit button Œ once to unlock driver’s door and fuel filler flap.
Choosing global or selective mode on remote control Important! Press and hold transmit buttons ‹ and Œ simultaneously for approx. 6 seconds to reprogram the remote control. Battery check lamp will blink two times indicating the completed mode change. Do not place remote control in trunk since trunk is locked when the lid is closed if the vehicle is centrally locked. Notes: If the trunk was previously locked separately, it will remain locked, see page 53.
Instruments and controls Operation Driving Instrument cluster display Central locking system KEYLESS-GO Important! For the KEYLESS-GO-system to function properly, the operator should observe the following: • The driver should carry the KEYLESS-GO-card with him/her. • To avoid radio transmission interference, never store the KEYLESS-GO-card together with other electronic items (e.g. cellular telephones, other KEYLESS-GOcards) or metallic objects (e.g. coins, metal foil).
• Opening the driver’s door with the engine shut off and no electronic key in the starter switch, the message “CHIP-CARD – DO NOT FORGET” appears as a reminder, see page 318. Notes: The KEYLESS-GO-function also permits closing of windows and sliding/pop-up roof (convenience feature), see page 46. With the KEYLESS-GO-card in close proximity (approx. 3 ft. [1 m]) of the vehicle, aiming a jet of water at a door handle (e.g.
Instruments and controls Operation Driving Instrument cluster display Central locking system Locking and unlocking with KEYLESS-GO-card Unlocking: Grasp either door handle. All turn signal lamps blink once to indicate that the vehicle is unlocked. The KEYLESS-GO-card can be programmed for two kinds of unlocking modes (see below): Selective unlocking mode – Grasp driver’s door handle to unlock driver’s door and fuel filler flap. Grasping the passenger door, centrally unlocks the vehicle.
Note: Locking the vehicle with the door lock button (1) is only possible if a KEYLESS-GO-card is outside the vehicle. Locking: Press lock button (1) at either door. All turn signal lamps blink three times to indicate that the vehicle is locked. If they do not blink three times, a door or trunk is not properly closed, or the KEYLESS-GO-card is still in the vehicle. Check the multifunction display, see page 318.
Instruments and controls Operation Driving Instrument cluster display Central locking system Practical hints Car care Technical data 42 Notes: If the trunk was previously locked separately, it will remain locked, see page 53. The vehicle cannot be centrally unlocked via the trunk lid lock (2). To prevent a possible inadvertent lockout, the trunk lid will open automatically if a KEYLESS-GO-card is recognized in the area of the rear shelf or inside the trunk.
Choosing global or selective mode on KEYLESS-GO-card Checking last KEYLESS-GO-card locking mode 2 Briefly press button (1). The indicator lamp (2) or (3) lights up in red (vehicle locked) or in green (vehicle unlocked). 3 1 To choose between the selective or global opening mode press and hold button (1) until the indicator lamp at the requested symbol (2) or (3) comes on.
Instruments and controls Operation Driving Instrument cluster display Central locking system Simultaneous use of electronic key and KEYLESS-GO-card When using the electronic key and the KEYLESS-GOcard at the same time, the electronic key overrules the KEYLESS-GO-card.
Continue to press transmit button ‹ after locking the vehicle. Opening and closing windows and sliding/pop-up roof from outside (summer opening/convenience feature) The windows and sliding/pop-up roof begin to close after approx. 1 second. Aim transmitter eye of remote control at a door receiver. To interrupt closing procedure, release transmit button.
Instruments and controls Operation Driving Instrument cluster display Central locking system Practical hints Car care Technical data 46 Note: Warning! If the windows and sliding/pop-up roof cannot be operated automatically by pressing the transmit button of the remote control then it may be necessary to change the batteries in the electronic main key (if ok, battery check lamp in electronic main key will light briefly when transmitting), or to synchronize the remote control, see page 363 and 365.
Panic button Note: For operation in the USA only: This device complies with Part 15, Subpart C, Section 209 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and 1 (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modification not expressly approved by party responsible for compliance could void the user’s authority to operate the equipment. P80.
Instruments and controls Operation Instrument cluster display Driving Central locking system Practical hints Car care Technical data 48 Doors 2 3 1 P80.30-2131-26 1 Opening – pull handle 2 Unlocking driver’s door 3 Locking driver’s door Important! The mechanical key does not operate the central locking system or antitheft alarm system. 4 Individual door from inside: Push lock button down to lock. 5 Individual door from inside: Pull handle to unlock.
If the vehicle has previously been locked from the outside, opening a door from the inside will trigger the alarm. When opening a door while the central locking system is in the: To unlock, pull inside door handles or turn mechanical key in driver’s door lock to position 2. When unlocking the driver’s door with the mechanical key, the exterior lamps will flash and the alarm will sound. • selective unlocking mode, only that individual door is unlocked.
Instruments and controls Operation Driving Instrument cluster display Central locking system Power closing assist for doors and trunk lid Practical hints Car care Technical data 50 Central locking switch The doors and the trunk lid close automatically if: • the doors are positioned against the lock, • the trunk lid is lowered against the lock.
If the vehicle was previously locked with the central locking switch, while in the global remote control mode, the complete vehicle is unlocked when a door is opened from the inside. Warning! When leaving the vehicle always remove the electronic key from the starter switch, take the KEYLESS-GO-card (if so equipped) with you, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause serious personal injury.
Instruments and controls Operation Driving Instrument cluster display Central locking system Automatic central locking With the automatic central locking system activated, the doors and trunk are locked at vehicle speeds of approx. 9 mph (15 km/h) or more. The fuel filler flap remains unlocked. The automatic central locking function can be switched on or off. See page 138 for “Individual settings”.
Trunk The lock is located in the license plate recess. When the trunk is separately locked, it remains locked when centrally unlocking the vehicle. To deny any unauthorized person access to the trunk, lock it separately with the mechanical key. Leave only the electronic key less its mechanical key with the vehicle. Notes: In case of a malfunction in the central locking system the trunk can be unlocked individually.
Instruments and controls Operation Driving Instrument cluster display Central locking system To cancel the alarm, insert the electronic key in the starter switch or press button Œ or ‹ on the electronic main key; or (vehicles with KEYLESS-GO) when carrying the KEYLESS-GO-card, grasp the door handle or press the start-/stop button on the gear selector lever. If the fuel filler flap cannot be opened, see page 368.
2 P88.50-2127-26 Vehicles without trunk lid opening/closing system: Vehicles with trunk lid opening/closing system: Lower trunk lid using handle (1) and close it with hands placed flat on trunk lid. Please remember to keep your fingers out of the space between the lid and the vehicle. Press trunk lid button (2) briefly. The trunk lid closes automatically. Central locking system Instruments and controls P54.
Instruments and controls Operation Driving Instrument cluster display Central locking system Warning! To prevent possible personal injury, always keep hands and fingers away from the trunk opening when closing the trunk lid. Be especially careful when small children are around. Always be sure persons who might get injured are away from the trunk area when you operate the trunk lid closing button located on the vehicle door.
Trunk lid release switch (Vehicles without trunk lid opening/closing system) The trunk lid will swing open automatically. You should always make sure there is sufficient clearance. A minimum height clearance of 6 ft. (1.85 m) is required to open the trunk lid. To open the trunk, the vehicle must be at standstill. Pull up on switch until trunk lid is open. The indicator lamp in the switch remains on with trunk lid open. Notes: The trunk can also be opened by using the remote control. Press Š button.
Instruments and controls Operation Driving Instrument cluster display Central locking system Trunk lid opening/closing system (optional) Practical hints Car care Technical data 58 To open trunk lid: Pull up on switch until trunk lid begins to open. The switch can now be released, the trunk lid opens automatically. To interrupt the opening process, either pull up on switch, or push in trunk lid lock, or press button Š on the remote control.
Notes: The trunk can also be opened by using the remote control. Press Š button. The automatic closing process is interrupted, if the trunk lid is pushed against an object. The trunk lid will reverse slightly and stop. In its final closing stage the hydraulic power closing assist mechanism releases the trunk lid which then drops into the lock by its own weight. Now the trunk lid will stop but not reverse slightly.
Instruments and controls Operation Driving Instrument cluster display Central locking system Practical hints Car care Technical data 60 Opening height restriction of trunk lid Note: The trunk lid opening height can be restricted when transporting goods on a roof rack (e.g. presence of an MB sport luggage container). When activated, the trunk lid opens to below the roof line of the vehicle. To fully open the trunk lid while opening height restriction activated, deactivate it.
Trunk lid emergency release Note: The emergency release button (1) only unlocks and opens the trunk while the vehicle is standing. Important! The emergency trunk lid release button (1) does not open the trunk lid, if: • the vehicle battery is discharged or disconnected, • the trunk lid was previously locked separately with the mechanical key, see page 53. Illumination of the emergency release button (1): The button will blink for 30 minutes after opening the trunk.
Instruments and controls Operation Driving Instrument cluster display Antitheft alarm system Antitheft alarm system Practical hints Car care Technical data 62 The antitheft alarm is armed within approx. 10 seconds after locking the vehicle with the remote control or the lock button at each door handle (vehicles with KEYLESS-GO). A blinking lamp (1) indicates that the alarm is armed.
Notes: To cancel the alarm, insert the electronic key in the starter switch or press button Œ or ‹ on the electronic main key; or (vehicles with KEYLESS-GO) when carrying the KEYLESS-GO-card, grasp the door handle or press the start-/stop button on the gear selector lever. We recommend that you carry the electronic reserve key plus mechanical key with you and keep it in a safe place (e.g. your wallet) so that it is always handy. Never leave the electronic reserve key in the vehicle.
Instruments and controls Operation Driving Instrument cluster display Tow-away alarm Tow-away alarm Practical hints Car care Technical data 64 Once the alarm system has been armed, the exterior vehicle lamps will flash and an alarm will sound when someone attempts to raise the vehicle. The alarm will last approximately 21/2 minutes in form of flashing exterior lamps. At the same time an alarm will sound for 30 seconds. The alarm will stay on even if the vehicle is immediately lowered.
To prevent triggering the tow-away alarm feature, switch off the tow-away alarm before towing the vehicle, or when parking on a surface subject to movement, such as a ferry or auto train. Exit vehicle, and lock vehicle with the electronic main key or (vehicles with KEYLESS-GO) the lock button at each door handle.
Instruments and controls Operation Driving Instrument cluster display Easy-entry/exit feature Easy-entry/exit feature Practical hints Car care Technical data 66 With the easy-entry/exit feature activated, the steering wheel tilts upwards to allow easier entry into and exit from the vehicle when the driver’s door is opened. However, the engine must be turned off.
Front seat adjustment When leaving the vehicle always remove the electronic key from the starter switch, take the KEYLESS-GO-card (if so equipped) with you, and lock your vehicle. Warning! Do not adjust the driver’s seat while driving. Adjusting the seat while driving could cause the driver to lose control of the vehicle. The power seats can also be operated with the driver’s or front passenger door open. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle.
Instruments and controls Operation Instrument cluster display Driving Seats Practical hints Car care Technical data 68 Note: 4 2 Do not move the front passenger seat completely forward if objects are stored in the parcel net in the front passenger side footwell. Items in the net may be damaged. 3 4 5 1 1 2 3 2 Seat, up/down Press the switch (up/down direction) until comfortable seating position with still sufficient headroom is reached.
6 7 6 Head restraint The height of the head restraint is adjusted automatically with the seat so that the back of the head is supported approximately at ear level. Adjust the head restraint using the switch if the preset position does not support the back of your head approximately at ear level. Adjust the head restraint angle (7) by hand. Push or pull the head restraint in direction of arrow.
Instruments and controls Operation Driving Instrument cluster display Seats Practical hints Car care Technical data 70 Important! Warning! Prior to operating the vehicle, the driver should adjust the seat height for proper vision as well as fore/aft placement and backrest angle to insure adequate control, reach, operation, and comfort. The head restraint should also be adjusted for proper height. See also airbag section on page 92 for proper seat positioning.
Removal and installation of front seat head restraints Note: Tilt the backrest rearward for easier removal and installation of the head restraints. To remove: Press switch (1) downwards and hold until the head restraint is fully retracted. Pull head restraint out with one strong jerking movement. 1 To install: Press switch (1) downwards and hold for about 5 seconds. Press the head restraint down until it engages. Adjust head restraint to the desired position. P91.
Instruments and controls Operation Driving Instrument cluster display Seats Practical hints Car care Technical data 72 Backrest Warning! The seat belts provide protection only with the backrest locked in place and, therefore, must be locked in place with the vehicle in motion. Do not drive the vehicle when the backrest is not locked in place.
Notes: When leaving the vehicle always remove the electronic key from the starter switch, take the KEYLESS-GO-card (if so equipped) with you, and lock your vehicle. The automatic seat slide is provided with a safety feature. The automatic process is interrupted, if the backrest of the sliding seat is pushed against an occupant or object. The seat will slide forward and stop. The power seats can also be operated with the driver’s or passenger door open.
Instruments and controls Operation Driving Instrument cluster display Seats Practical hints Technical data Car care 74 Lumbar support (optional) Multicontour backrest (optional) 2 1 3 4 1 P91.10-2089-26 The thumbwheels are located on the sides of the front seats. The seats have an inflatable air cushion built into the backrest to provide additional lumbar support. Turn the electronic key in starter switch to position 2.
3 Backrest side cushions Some models may be equipped with multicontour seats. These seats have inflatable air cushions built into the backrests to provide additional lumbar and side support. The lateral support increases or decreases as you press the button to the right or left. Adjust the side cushions to provide good lateral support. Turn the electronic key in starter switch to position 2 to operate.
Instruments and controls Operation Driving Instrument cluster display Seats Practical hints Car care Technical data 76 Seat heater The seat heaters can be switched on with the electronic key in starter switch positions 1 or 2. The buttons are located on each door. Notes: When in operation, the seat heater consumes a large amount of electrical power. It is not advisable to use the seat heater longer than necessary.
Vehicles without seat ventilation function: Normal heating mode: Press button (1). One indicator lamp in the switch lights up. The seat heater will be automatically switched off after approximately 30 minutes. 1 Rapid heating mode: Press button (2). Both indicator lamps in the switch light up. 2 The system switches over to normal heating mode automatically after approximately 5 minutes. P54.25-2131-26 Turning off the heater: Press button (1) or (2) again. The indicator lamps go out.
Instruments and controls Operation Instrument cluster display Driving Seats Practical hints Car care Technical data 78 Vehicles with seat ventilation function: Rapid heating mode: Press button (3) once. Both red indicator lamps above the button light up. The system switches over to normal heating mode automatically after approximately 5 minutes. Normal heating mode: Press button (3) twice. One red indicator lamp above the button lights up. 3 P54.
Seat ventilation system The seat ventilators may automatically switch off if too many power consumers are switched on at the same time or if the battery charge is low. In this case, one or more indicator lamps will blink. The buttons are located on each door. Seat ventilation can be activated manually with the electronic key in starter switch positions 1 or 2, or by the summer opening function, see page 45.
Instruments and controls Operation Driving Instrument cluster display Seats Practical hints Car care Technical data 80 Level 2 ventilation setting (middle): Press button (1) again. Two blue indicator lamps above the button light up. Level 1 ventilation setting (minimum): Press button (1) again. One blue indicator lamp above the button lights up. Turning off the seat ventilation: Press button (1) again. The indicator lamps go out. The seat ventilation is switched off. 1 P54.
Power head restraints, rear Important! For safety reasons, always drive with the rear head restraints in the upright position when the rear seats are occupied. Keep the area around head restraints clear of articles (e.g. clothing) to not obstruct the folding operation of the head restraints. Notes: Both head restraints fold up or back together. The head restraints will position themselves automatically when the seats are occupied (seat belt buckled).
Instruments and controls Operation Driving Instrument cluster display Restraint systems Practical hints Car care Technical data 82 Seat belts and integrated restraint system Warning! Your vehicle is equipped with seat belts for all seats, emergency tensioning retractors, dual front airbags, side impact airbags for driver, front and rear passengers, and head protective window curtain airbags. Their protective functions are designed to complement one another.
Warning! Seat belt nonusage warning system The seat belts provide protection only with the backrest locked in place. Do not drive the vehicle when the backrest is not locked in place. If the warning message “SEAT BACKREST LEFT – LOCK!” or “SEAT BACKREST RIGHT – LOCK!” is displayed in the multifunction display, then the respective backrest is not engaged in its lock. For backrest see page 72.
Instruments and controls Operation Driving Instrument cluster display Restraint systems Practical hints Car care Technical data 84 Warning! Warning! Failure to wear and properly fasten and position your seat belt greatly increases your risk of injuries and their likely severity in an accident. You and your passengers should always wear seat belts. Never let more people ride in the vehicle than there are seat belts available.
Fastening seat belts 1 Latch plate 2 Buckle 3 Release button Push the latch plate (1) into the buckle (2) until it clicks. Do not twist the belt. A twisted seat belt may cause injury. 1 3 To help avoid severe or fatal injuries, the lap belt should be positioned as low as possible on your hips and not across the abdomen. 2 Warning! Always fasten your seat belt before driving off. Always make sure your passengers are properly restrained – even those sitting in the rear.
Instruments and controls Operation Driving Instrument cluster display Restraint systems Practical hints Car care 86 Operation of seat belts Warning! The inertia reel stops the belt from unwinding during sudden stops or when quickly pulling on the belt. USE SEAT BELTS PROPERLY. The locking function of the reel may be checked by quickly pulling out the belt. Caution! For safety reasons, avoid adjusting the seat or seat back into positions which could affect the correct seat belt positioning.
• Never wear the shoulder belt under your arm, against your neck or off your shoulder. In a crash, your body would move too far forward. That would increase the chance of head and neck injuries. The belt would also apply too much force to the ribs or abdomen, which could severely injure internal organs such as your liver or spleen. • Each seat belt should never be used for more than one person at a time. Do not fasten a seat belt around a person and another person or other objects.
Instruments and controls Operation Driving Instrument cluster display Restraint systems Warning! USE CHILD RESTRAINTS PROPERLY. Children 12 years old and under must never ride in the front seat, except in a Mercedes-Benz authorized BabySmartTM compatible child seat, which operates with the BabySmartTM system installed in the vehicle to deactivate the passenger front airbag when it is properly installed. Otherwise they will be struck by the airbag when it inflates in a crash.
Self-test BabySmartTM without special child seat installed Warning! The BabySmartTM airbag deactivation system will ONLY work with a special child seat designed to operate with it. It will not work with child seats which are not BabySmartTM compatible. After turning electronic key in starter switch to position 1 or 2, the 7 indicator lamp located on the center console comes on for approx. 6 seconds and then extinguishes. Never place anything between seat cushion and child seat (e.g.
Instruments and controls Operation Driving Instrument cluster display Restraint systems Supplemental restraint system (SRS) Airbags are intended as a supplement to seat belts. Airbags alone cannot protect as well as airbags plus seat belts in impacts for which the airbags were designed to operate, and do not afford any protection whatsoever in crashes for which the airbags are not designed to deploy.
Emergency tensioning retractor (ETR) and in rear impacts exceeding a preset severity level. They remove slack from the belts in such a way that the seat belts fit more snugly against the body restricting its forward movement as much as possible. The seat belts for the front and rear seats are equipped with emergency tensioning retractors. These tensioning retractors are located in each belt’s inertia reel and become operationally ready with the electronic key in starter switch position 1 or 2.
Instruments and controls Operation Driving Instrument cluster display Restraint systems Practical hints Car care Technical data 92 Airbags 1 Driver airbag Front airbags 2 Front passenger airbag The most effective occupant restraint system yet developed for use in production vehicles is the seat belt. In some cases, however, the protective effect of a seat belt can be further enhanced by an airbag.
come on at all or if it fails to extinguish after approximately 4 seconds or if it comes on thereafter, a malfunction in the system has been detected. In the operational mode, after the indicator lamp has gone out following the initial check, interruptions or short circuits in the airbag ignition circuit and in the driver and front passenger seat belt buckle harnesses, and low voltage in the entire system are detected and indicated.
Instruments and controls Operation Driving Instrument cluster display Restraint systems The driver and passenger front airbags are designed to activate only in certain frontal impacts exceeding a preset threshold. The front passenger airbag deploys only if the front passenger seat is occupied and the 7 indicator lamp on the center console is not illuminated.
Side impact airbags, window curtain airbags Side impact airbags The side impact airbags are designed to activate only in certain side impacts exceeding a preset threshold. Only the side impact airbags on the impacted side of the vehicle deploy. 4 The side impact airbag for the front passenger deploys only if the front passenger seat is occupied. 3 The side impact airbag for the right rear passenger deploys only if a preset threshold is exceeded.
Instruments and controls Operation Driving Instrument cluster display Restraint systems Window curtain airbags The head protection window curtain airbags afford greater protection against injuries to the head and upper body. They fill up in the area between the A and C pillars (see arrows) between the side windows and an occupant’s head. The window curtain airbags are designed to activate only in certain side impacts exceeding a preset threshold.
Your vehicle was originally equipped with airbags which are designed to activate in certain impacts exceeding a preset threshold to reduce the potential and severity of injury. It is important to your safety and that of your passenger that you replace deployed airbags and repair any malfunctioning airbags to ensure the vehicle will continue to provide crash protection for occupants. • Sit properly belted in an upright position with your back against the backrest.
Instruments and controls Operation Driving Instrument cluster display Restraint systems • Occupants, especially children, should never lean their heads in the area of the door or rear quarter interior trim panel where the side airbag inflates. This could result in serious injuries or death should the airbag be triggered. Always sit upright, properly use the seat belts and appropriate size infant or child restraint system.
To help avoid the possibility of injury, please follow these guidelines: (1) occupants, especially children, should never place their bodies or lean their heads in the area of the front door or rear quarter trim panels where the side airbag inflates.
Instruments and controls Operation Driving Instrument cluster display Restraint systems Safety guidelines for the seat belt, emergency tensioning retractor and airbag Warning! • Damaged seat belts or belts that were highly stressed in an accident must be replaced and their anchoring points must also be checked. Use only belts installed or supplied by an authorized Mercedes-Benz Center. • Airbags and “ETR’s” are designed to function on a one-time-only basis.
When you sell your vehicle we strongly urge you to give notice to the subsequent owner that it is equipped with an “SRS” by alerting them to the applicable section in the Operator’s Manual. • For your protection and the protection of others, when scrapping the airbag unit or emergency tensioning retractor, our safety instructions must be followed. These instructions are available from your authorized Mercedes-Benz Center.
Instruments and controls Operation Driving Instrument cluster display Restraint systems Practical hints Car care Technical data 102 Infant and child restraint systems Important! We recommend all infants and children be properly restrained at all times while the vehicle is in motion. All lap-shoulder belts except the driver seat belt have special seat belt retractors for secure fastening of child restraints.
Warning! Children too big for child restraint systems must ride in back seats using regular seat belts. Position shoulder belt across chest and shoulder, not face or neck. A booster seat may be necessary to achieve proper belt positioning for children from 41 lbs. to the point where a lap/shoulder belt fits properly without one.
Instruments and controls Operation Driving Instrument cluster display Restraint systems Practical hints Car care Technical data 104 Installation of infant and child restraint systems 1 P91.40-2205-26 This vehicle is provided with tether anchorages for a top tether strap at each of the rear seating positions. Prior to installing a tether strap, remove cover (1) from anchorage ring (2) and store in a convenient place (e.g. glove box).
Steering wheel adjustment 2 Warning! 1 Do not adjust the steering wheel while driving. Adjusting the steering wheel while driving could cause the driver to lose the control of the vehicle. When leaving the vehicle always remove the electronic key from the starter switch, and take the KEYLESS-GO-card (if so equipped) with you. The steering wheel adjustment feature can also be operated with the driver’s door open. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle.
Instruments and controls Operation Driving Instrument cluster display Rear view mirrors Practical hints Car care Technical data 106 Rear view mirrors Note: Inside rear view mirror The automatic antiglare function does not react, if incoming light is not aimed directly at sensors in the mirror. Manually adjust the mirror.
Exterior rear view mirrors Exterior mirror adjustment Turn the electronic key in starter switch to position 2. Push button to select mirror to be adjusted: Driver’s side – Push button (1). Passenger side – Push button (2). 2 1 Push the adjustment button (3) up, down, left or right according to the setting desired. 3 4 Note: The exterior rear view mirrors have electrically heated glass. The heater switches on automatically, depending on outside temperature. P88.
Instruments and controls Operation Driving Instrument cluster display Rear view mirrors Parking position The passenger side exterior mirror can be adjusted and programmed to assist the driver during parking maneuvers (e.g. to observe the curb or other objects close to the vehicle).
Exterior mirrors, electrically folding Important! If an exterior mirror housing is forcibly pushed forward (hit from the rear), it must be repositioned manually by applying firm pressure until it snaps back into place. If an exterior mirror is forcibly pushed rearward (hit from the front), press button (2) to fold mirrors in, then press button (1) to fold mirrors out. Do not force mirror by hand.
Instruments and controls Operation Driving Instrument cluster display Rear view mirrors Practical hints Car care Technical data 110 Driver’s side exterior mirror, antiglare mode Warning! Antiglare mode: With the electronic key in starter switch position 2, the mirror reflection brightness responds to changes in light sensitivity. In the case of an accident liquid electrolyte may escape the mirror housing when the mirror glass breaks.
Memory function Three sets of seat/head restraint/steering wheel/and rear view mirror positions may be stored into memory. Together with the driver’s seat position you can store the positions for steering wheel, exterior mirrors and rear-view mirror. For the front passenger you can store the seat position. Three stored positions are available for each of the two electronic main keys or each of the KEYLESS-GO-cards. The memory and stored position buttons are located on the doors.
Instruments and controls Operation Driving Instrument cluster display Memory function Practical hints Car care Technical data 112 Storing positions into memory Recalling positions from memory Driver’s seat: with the electronic key in starter switch position 1 or 2 or with the driver’s door open and the electronic key inserted in the starter switch.
Important! Warning! Prior to operating the vehicle, the driver should check and adjust if necessary the seat height, seat position fore and aft, and backrest angle to insure adequate control, reach and comfort. The head restraint should also be adjusted for proper height. See also airbag section for proper seat positioning.
Instruments and controls Operation Instrument cluster Driving Instrument cluster display Practical hints Car care Technical data 114 Instrument cluster P54.
1 Knob for instrument cluster illumination, see page 116 12 Multifunction display, see page 120 Instrument cluster display, see page 297 2 Engine malfunction indicator lamp, see page 290 13 Trip odometer, see page 119 and 124 3 Brake fluid low or parking brake engaged, see page 301 14 Main odometer, see page 124 15 Right turn signal indicator lamp, see combination switch on page 160 4 Supplemental restraint system (SRS) malfunction indicator lamp, see page 293 16 Tachometer, see page 119 5 Coolant t
Instruments and controls Operation Driving Instrument cluster display Instrument cluster Practical hints Car care Technical data 116 • Turning the electronic key in starter switch to position 1 or 2. Display illumination, changing basic settings for driving at dusk or in darkness: • Switching on the exterior lamps. Press adjusting knob (1) – the knob will pop out. 1 The instrument cluster is activated for approx. 30 seconds.
Coolant temperature gauge (5) Outside temperature indicator (6) During severe operating conditions and stop-and-go city traffic, the coolant temperature may rise close to the red marking. Warning! The outside temperature indicator is not designed to serve as an Ice-Warning Device and is therefore unsuitable for that purpose. Indicated temperatures just above the freezing point do not guarantee that the road surface is free of ice.
Instruments and controls Operation Driving Instrument cluster display Instrument cluster Practical hints Car care 118 Speedometer (9) Note: When the cruise control is activated, the segments on the speedometer scale between the set speed to the top of the scale are illuminated. Cruise control, see page 250. The speed display is set to read out for When the Distronic (DTR) is activated, one or two segments around the speed stored in memory light up in the speedometer dial.
Trip odometer (13) Tachometer (16) To reset to “0” miles/km: The red marking on the tachometer denotes excessive engine speed. Activate the instrument cluster if it is not already activated by pressing the J button on the instrument cluster. Avoid this engine speed, as it may result in serious engine damage that is not covered by the Mercedes-Benz Limited Warranty. Press button è or ÿ on the multifunction steering wheel repeatedly until the trip odometer appears if it is not displayed. See page 124.
Instruments and controls Operation Driving Instrument cluster display Multifunction steering wheel, multifunction display Multifunction steering wheel, multifunction display Practical hints 120 Car care Technical data Index
4 Navigation system, see page 132 Depending on your vehicle’s equipment, you may use the buttons on the multifunction steering wheel to call up, control and set the following systems in the multifunction display: 5 Distronic (DTR), see page 253 6 Trip computer, see page 134 After start After reset Fuel tank content 1 Trip odometer and main odometer, see page 119 and page 124 Flexible service system (FSS), see page 147 Tire inflation pressure monitor, see page 150 Engine oil level indicator, see page 154
Instruments and controls Operation Driving Instrument cluster display Multifunction steering wheel, multifunction display Practical hints Car care Technical data 122 Warning! Note: A driver’s attention to the road must always be his/ her primary focus when driving. The displays in the multifunction display can be set to German, English, French, Italian or Spanish language. See the “TEXT” individual setting on page 140 for instructions on changing the language setting.
Turn the electronic key in starter switch to position 1 or 2. 1 Press button: 4 j for next display in system 5 k for previous display in system 2 6 è for next system 7 ÿ for previous system 4 5 8 3 3 6 8 æ to increase the volume, see page 146 9 7 9 ç to decrease the volume, see page 146 10 10 í to dial a telephone number, see page 128 11 11 ì to end a call See page 128 for telephone and page 131 for instructions on answering an incoming call.
Instruments and controls Operation Driving Instrument cluster display Multifunction steering wheel, multifunction display Trip and main odometer, FSS, tire inflation pressure monitor and engine oil level indicator Practical hints Car care Technical data 124 1 Trip odometer and main odometer See page 119 for instructions on resetting the trip odometer.
Audio systems 1 Audio system is switched off. Radio 2 The radio is switched on. 3 Wave band setting and memory location number, where appropriate. 4 Station name setting or station frequency. 5 This only appears when “MEMORY” rather than “FREQUENCY” has been selected in the Individual settings “VEHICLE”. See page 144. Switch on the radio, see COMAND operator’s manual. Press the è or ÿ button repeatedly until display (2) appears.
Instruments and controls Operation Driving Instrument cluster display Multifunction steering wheel, multifunction display CD player Practical hints Car care Technical data 126 1 Audio system is switched off. 2 The CD player is switched on. 3 The number of the CD currently playing is displayed if you are using a CD changer. 4 Track number. Switch on the CD player, see COMAND operator’s manual. Press the è or ÿ button repeatedly until display (2) appears.
Cassette player 1 Audio system is switched off. 2 The cassette player is switched on. 3 Side being played. Switch on the cassette player, see COMAND operator’s manual. Press the è or ÿ button repeatedly until display (2) appears. Pressing the j button fast forwards on to the next track. Pressing the k button rewinds the cassette to the beginning of the current track. Pressing the è or ÿ button displays the next or previous system.
Instruments and controls Operation Driving Instrument cluster display Multifunction steering wheel, multifunction display Practical hints Car care Technical data 128 Telephone 1 The telephone is switched off. Telephone book 2 The vehicle is currently outside the transmitter or receiver range. 3 The telephone is ready for use. 4 Name selected from the telephone book. 5 Number for the name selected. Dialing commences. 6 Dialing is completed. The name is displayed.
Press the í button when the name you require appears in the display (4). The telephone number (5) is dialed. The telephone must be switched on. Press the è or ÿ button repeatedly until the display (3) appears. See the separate telephone instructions manual. The name will be displayed when dialing is completed. Display (6) remains for the duration of the call. If display (2) appears, no service is available. Pressing the ì button hangs up and display (3) appears.
Instruments and controls Operation Driving Instrument cluster display Multifunction steering wheel, multifunction display Redialing Practical hints Car care Technical data 130 1 The telephone is ready for use. 2 Number or name stored in the redial memory. 3 Number in the redial memory — redialing has commenced. 4 Dialing is completed and the name stored in the telephone book is displayed or the number dialed will remain displayed if no name has been stored.
Incoming call The telephone must be switched on. Press the è or ÿ button repeatedly until the display (1) appears. Pressing the í button activates the redial memory and the most recently dialed number is displayed. Pressing the j or k button “browses” forward or backwards through the redial memory. The number selected appears in the display. Note: The telephone must be switched on. Press the ì button if you do not wish to make a call. 1 “CALL” — you are being called.
Instruments and controls Operation Driving Instrument cluster display Multifunction steering wheel, multifunction display Navigation system Practical hints Car care Technical data 132 1 The navigation system is switched off. 2 The navigation system is switched on but no destination has been specified. 3 The navigation system is switched on and destination guidance is active. Press the è or ÿ button repeatedly until the required system is displayed.
Distronic (DTR) 1 Distronic (DTR) is deactivated. The actual distance (4) and the should-be distance (5) to the vehicle in front (3) are displayed. 2 Distronic (DTR) is activated. The message “DTR OFF” appears for five seconds when Distronic is being deactivated. 3 Vehicle ahead. Only appears if a vehicle is detected ahead. 4 Actual distance to vehicle ahead. 5 Should-be distance to vehicle ahead. 6 Own vehicle. Press the è or ÿ button repeatedly until the required system is displayed.
Instruments and controls Operation Driving Instrument cluster display Multifunction steering wheel, multifunction display Trip computer Practical hints Car care Technical data 134 1 “AFTER START” — short distance memory 2 “AFTER RESET” — long distance memory 3 Fuel tank contents and estimated range remaining 4 Distance covered “AFTER START” or “AFTER RESET” 5 Elapsed time “AFTER START” or “AFTER RESET” 6 Average speed “AFTER START” or “AFTER RESET” 7 Average fuel consumption “AFTER START” or “AFTER
Transferring values from the previous journey to the “AFTER START” short distance memory (1): To reset the short “AFTER START” (1) or long “AFTER RESET” distance memory (2): The “AFTER START” display will flash until a distance of approximately 1 mile (1.6 km) has been covered or two minutes have elapsed since the engine was restarted. During this period you can incorporate the values for the previous journey by pressing button J in the instrument cluster.
Instruments and controls Operation Driving Instrument cluster display Multifunction steering wheel, multifunction display Malfunction/warning message memory Practical hints Car care Technical data 136 Press the è or ÿ button repeatedly until the message memory (1 or 2) is displayed. Press the j or k button if display (2) appears. The stored messages will now be displayed in order. See page 297 for malfunction and warning messages.
Important! The message memory will be cleared when the electronic key is turned in the starter switch to position 1 or 2. Should any subsequent faults occur, they will be displayed in the message memory. Malfunction and warning messages are only indicated for certain systems and displayed to a low level of detail.
Instruments and controls Operation Driving Instrument cluster display Multifunction steering wheel, multifunction display Individual settings Practical hints Car care Technical data 138 1 Preliminary display of the individual settings. 2 “SETTINGS” – the requested menu can be called up in this options menu: “INSTRUMENT CLUSTER”, see page 140. “LIGHTING”, see page 142. “VEHICLE”, see page 144. R These three menus contain additional submenus. Individual settings can be selected in these submenus.
Press the è or ÿ button repeatedly until the individual setting preliminary display (1) appears. To return menu “SETTINGS” (2) to its factory setting: Press the j or k button until the setting menu “SETTINGS” (2) is displayed. • Call up the individual setting preliminary display (1). Pressing the æ or ç button controls the selection marker (3) in setting menu (2). • Press the J button in the instrument cluster for approximately 3 seconds. Display (4) will appear. “INSTRUMENT CLUSTER”, see page 140.
Instruments and controls Operation Driving Instrument cluster display Multifunction steering wheel, multifunction display Practical hints Car care Technical data 140 “INSTRUMENT CLUSTER” 3 R Index
Press button æ or ç until the menu “INSTRUMENT CLUSTER” is selected by the selection marker (3). 1 Preliminary display of the individual settings 2 “SETTINGS” – the menu “INSTRUMENT CLUSTER” can be called up in this option menu. Press the j or k button until the required display (4 to 6) is displayed. Pressing the æ or ç button controls the selection marker. The settings made are stored and applied immediately.
Instruments and controls Operation Instrument cluster display Driving Multifunction steering wheel, multifunction display Practical hints Car care Technical data 142 “LIGHTING” R 7 Index
Press button æ or ç until the menu “LIGHTING” is selected by the selection marker (3). 1 Preliminary display of the individual settings 2 “SETTINGS” – the menu “LIGHTING” can be called up in this option menu. Press the j or k button until the required display (4 to 7) is displayed. Pressing the æ or ç button controls the selection marker. The settings made are stored and applied immediately. 3 Selection marker Pressing button æ or ç on the multifunction steering wheel controls the selection marker.
Instruments and controls Operation Instrument cluster display Driving Multifunction steering wheel, multifunction display Practical hints Car care Technical data 144 “VEHICLE” (audio and central locking system) R 5 Index
Press button æ or ç until the menu “VEHICLE” is selected by the selection marker (3). 1 Preliminary display of the individual settings 2 “SETTINGS” – the menu “VEHICLE” can be called up in this option menu. Press the j or k button until the required display (4 or 5) is displayed. Pressing the æ or ç button controls the selection marker. The settings made are stored and applied immediately. 3 Selection marker Pressing button æ or ç on the multifunction steering wheel controls the selection marker.
Instruments and controls Operation Driving Instrument cluster display Multifunction steering wheel, multifunction display Practical hints Car care 146 Setting the audio volume Setting button: You can only adjust the volume of the system currently in use. The volume setting for each system (audio, telephone, navigation and voice recognition system) is stored separately. æ increases the volume. ç reduces the volume.
Flexible service system (FSS) (service indicator) The message is displayed for approx. 10 seconds when turning the electronic key in starter switch to position 2, or while driving when reaching the service warning threshold. The symbols and messages indicate the type of service to be performed: 9 Service A ½ Service B One of the following messages will appear in the display (e.g.
Instruments and controls Operation Driving Instrument cluster display Flexible service system The service indicator disappears automatically after 30 seconds or if button J on the instrument cluster is pressed. Calling up service indicator manually: Turn the electronic key in starter switch to position 1. Call up the trip odometer and main odometer by pressing button è or ÿ on the multifunction steering wheel until the display appears. See page 124. Press button j or k until the FSS indicator appears.
Following a completed A or B service the Mercedes-Benz Center sets the counter mileage to 10 000 miles (Canada: 15 000 km) and 365 days. The multifunction display will show the question: “DO YOU WANT TO RESET SERVICE INTERVAL? – CONFIRM BY PRESSING R” The counter can also be set by any individual. To do so: Press button J on the instrument cluster again to reset the service indicator. Turn the electronic key in starter switch to position 1.
Instruments and controls Operation Driving Instrument cluster display Tire inflation pressure monitor Tire inflation pressure monitor Practical hints Car care Technical data 150 Inquiry of present tire inflation pressure The tire inflation pressure, as selected by the driver, is monitored in all four wheels on the ground. A warning is issued to the driver in the case of a decrease in the inflation pressure in one or more of the tires.
Notes: Activation of tire inflation pressure monitor Following a tire inflation pressure reactivation process the real tire inflation pressures are displayed only after a few minutes travel time. Activation of tire inflation pressure monitor is necessary if tire inflation pressure is being changed, wheels or tires are replaced, or new wheels are installed on the vehicle. Possible differences between readings of a tire pressure gauge of an air hose, e.g.
Instruments and controls Operation Driving Instrument cluster display Tire inflation pressure monitor Practical hints Car care Technical data 152 Press and hold button J on the instrument cluster again until the message “TIRE PRESS. CONTROL – ACTIVATED!” appears. The tire inflation pressure monitor is now activated and monitors the presently selected tire pressure for all four wheels on the ground. Repeat above steps if the multifunction display shows the message “TIRE PRESS. CONTROL – REACTIVATE!”.
Notes: Transporting a deflated road wheel in the vehicle, e.g. after having a flat, the tire inflation pressure monitor should only be activated once the flat tire and rim are removed from the vehicle. Otherwise the monitor displays the message “TIRE PRESS. CONTROL – CURRENTLY INACTIVE”. To ensure proper functioning of the tire inflation pressure monitor, the tire inflation pressure should be checked and corrected according to the label affixed inside the fuel filler flap.
Instruments and controls Operation Driving Instrument cluster display Engine oil level indicator Engine oil level indicator Practical hints Car care Technical data 154 • with engine not at operational temperature up to approx. 30 minutes. The engine oil level check can be repeated after a short time. Turn the electronic key in starter switch to position 2. To call up the trip odometer and main odometer, press button è or ÿ on the multifunction steering wheel until the display appears. See page 124.
One of the following messages will subsequently appear on the indicator: CL 500 and CL 55 AMG only: Perform the engine oil level check with the dipstick, if it cannot be completed via the multifunction display. See “Checking engine oil level”, page 331. In this case we recommend that you have the system checked at a Mercedes-Benz Center. “ENGINE OIL LEVEL – O.K.” No oil needs to be added. “ENGINE OIL LEVEL – ADD 1.0 QUART” (Canada: 1.0 L) Notes: “ENGINE OIL LEVEL – ADD 1.5 QUART” (Canada: 1.
Instruments and controls Operation Driving Instrument cluster display Exterior lamp switch Practical hints Car care Technical data 156 ˆ Standing lamps, right (turn left one stop) Exterior lamp switch ‚ Standing lamps, left (turn left two stops) ‡ Front fog lamps (pull out one stop) with parking lamps and/or low beam headlamps on. Green indicator in lamp switch comes on. † Rear fog lamp (pull out to second detent) in addition to the front fog lamps. Yellow indicator in lamp switch comes on.
Headlamp mode (HEADLAMPS) (USA only) Automatic operation: With electronic key in starter switch in position 1 turn exterior lamp switch to position U. The headlamps can be switched on and off manually or automatically, or switched to daytime running lamp mode. The parking lamps switch on and off automatically depending on the brightness of the ambient light.
Instruments and controls Operation Driving Instrument cluster display Exterior lamp switch Practical hints Car care Technical data 158 Daytime running lamp mode Night security illumination Turn exterior lamp switch to position M. When turning off the engine, the exterior lamps switch on for added illumination, if they were previously switched on (except in daytime running mode). After the last door has been closed the lamp-on time period commences.
Locator lighting Headlamp cleaning system After unlocking the vehicle with the electronic main key during darkness, the fog lamps, parking lamps, taillamps and license plate lamps switch on for a approx. 40 seconds. The exterior lamps will be switched off when opening the driver’s door. See “Individual settings” – “LIGHTING” on page 142 for instructions on how to activate the function. 1 P54.25-2391-26 Turn the electronic key in starter switch to position 1 or 2.
Instruments and controls Operation Driving Instrument cluster display Combination switch Car care Technical data 160 Combination switch 4 Practical hints 3 High beam flasher (high beam available independent of exterior lamp switch position) 4 Turn signals, right 4 5 Turn signals, left To signal minor directional changes, such as changing lanes on a highway, move combination switch briefly to the point of resistance only and release. The turn signals blink three times.
0 Off I 7 Intermittent wiping One initial wipe, pauses between wipes are automatically controlled by a rain sensor monitoring the wetness of the windshield. This will not occur with a front door open. Notes: With switch in this position, one wipe occurs when turning the electronic key in starter switch from position 0. This will not occur with a front door open. 6 P54.25-2389-26 Do not leave in intermittent setting when vehicle is taken to an automatic car wash or during windshield cleaning.
Instruments and controls Operation Driving Instrument cluster display Combination switch Practical hints Car care Technical data 162 Blocked windshield wipers Windshield wipers smear If the windshield wipers become blocked (for example, due to snow), switch off the wipers. For safety reasons before removing ice or snow, remove electronic key from starter switch. Remove blockage. If the windshield wipers smear the windshield, even during rain, activate the washer system as often as necessary.
Hazard warning flasher switch Note: With the hazard warning flasher activated, the combination switch in position for either left or right turn, and the electronic key in starter switch position 1 or 2, only the respective left or right side turn signals will operate. The hazard warning flasher can be activated either manually via the switch located in the dashboard, or it is activated automatically at the time an airbag is deployed. To activate hazard warning flasher, press switch once.
Instruments and controls Operation Driving Automatic climate control Instrument cluster display Practical hints Technical data Car care 164 Automatic climate control 8 7 2 9 1 3 4 5 12 6 11 10 3 P83.
1 Center air outlet, left, adjustable 6 Center air outlet, right, adjustable 2 Fixed air outlet, left 7 Fixed air outlet, right 3 Air volume control for left center air outlet 8 Side defroster outlet, left and right, fixed To open: Turn the thumbwheel upward. 9 Side air outlet, left and right, adjustable ■: The left center air outlet is fully open. 10 Air volume control for side air outlets ■■: The left center and fixed air outlets are opened.
Instruments and controls Operation Instrument cluster display Driving Automatic climate control Practical hints Car care Technical data 166 8 Air volume (automatic, manual) Display and controls 9 Display 1 2 Depending on the ambient light conditions, the figures on the display will be shown as dark figures on a bright background (in daylight), or as bright figures on a dark background (at night).
Automatic climate control Notes: The system is always at operational readiness, except when manually switched off. Do not obstruct the air flow by placing objects on the air flow-through exhaust slots below the rear window. The automatic climate control only operates with the engine running. Also keep the air intake grill in front of the windshield free of snow and debris. The temperature selector should be left at the desired temperature setting.
Instruments and controls Operation Driving Instrument cluster display Automatic climate control Basic setting – automatic mode Practical hints Car care Technical data 168 Air volume and distribution are controlled automatically. Set the temperature switches on the left and right to 72°F (22°C). This provides for comfortable conditions in the vehicle. Automatic airflow regulation: There are three basic settings for the automatic mode: Press the A on the air volume switch. The display shows “AUTO”.
Special settings (use only for short duration) Air volume, manual P83.40-2257-21 Air distribution, manual: Press the air volume switch up or down. Seven blower speeds can be selected. Press U button. The button pops out, the h, j and k symbols are visible. Turn the button to select the air distribution desired. h Air from the center, side and door air outlets. j Air from the center, side, door and windshield air outlets. k Air from the center, side, door and footwell air outlets.
Instruments and controls Operation Driving Instrument cluster display Automatic climate control Practical hints Car care Technical data 170 Defrosting Windows fogged on the inside Switch off the economy mode, if selected: Press button S. The indicator lamp in the button will go out. Switch off air recirculation, if selected: Press button O. The indicator lamp in the button will go out. P83.40-2009-21 Press the P button. The display shows P.
Windshield fogged on the outside The system automatically switches from air recirculation to fresh air: Switch on the windshield wiper. • after 30 minutes if the outside temperature is above about 40°F (5°C), Press on both U buttons until they click in. The h, j and k symbols will no longer be visible. • after 5 minutes if the outside temperature is below about 40°F (5°C), • after 5 minutes if economy mode S is selected.
Instruments and controls Operation Driving Instrument cluster display Automatic climate control Activated charcoal filter An activated charcoal filter markedly reduces bad odors and removes pollutants from air entering the passenger compartment. To select, press e button. The indicator lamp in the button illuminates. To cancel, press e button. The indicator lamp in the button goes out.
Press S button to activate. The indicator lamp in the button illuminates. Economy mode The function of this setting corresponds to the automatic mode. However, because the air conditioning compressor will not engage (fuel savings), it is not possible to air condition in this setting. Press S button once again to return to the previous setting. Important! In the S mode the windows could fog up on the inside. Switch off S mode.
Instruments and controls Operation Driving Instrument cluster display Automatic climate control Residual engine heat utilization Practical hints Car care Technical data 174 The function switches off automatically: • if the electronic key in starter switch is turned to position 2, • after approximately 30 minutes, • if the battery voltage drops. Note: With the engine switched off, it is possible to continue to heat or ventilate the interior for a short while.
Switching the automatic climate control on and off Front center console storage compartment ventilation The front center console compartment has its own air outlet. To open: Slide the lever up. To close: Slide the lever down. The air volume is dependent on the setting of: • air distribution control, To switch off: Press button 0. The display shows “0”. • air volume control, • air outlets in the dashboard. The fresh air supply to the vehicle interior is shut off.
Instruments and controls Operation Driving Instrument cluster display Automatic climate control Rear window defroster Turn the electronic key in starter switch to position 2. To select: Press the F button in the control panel of the automatic air conditioner. The indicator lamp in the button illuminates. Practical hints Car care Technical data 176 The rear window defroster uses a large amount of power.
Rear passenger compartment adjustable air outlets 1 Center air outlet, left 2 Center air outlet, right 3 Air volume control for center air outlets To open: Turn the wheel to the left. 1 2 3 P83.
Instruments and controls Operation Driving Instrument cluster display Interior equipment Practical hints Car care Technical data 178 Power windows 3 3 3 3 The control panel is located on the driver’s door. Control panel on rear center console. Switches for: Turn electronic key in starter switch to position 1 or 2. 1 left, front 2 right, front Opening the side windows: Press k on the switch to resistance point.
Express opening and closing of windows Warning! Press k or j on the switch past resistance point and release – window opens or closes completely. When closing the windows, be sure that there is no danger of anyone being harmed by the closing procedure. To interrupt procedure, briefly press j or k. In case of obstruction, the automatic reversal will not operate if a door window is being closed by pressing the switch to its resistance point and holding it there, or when using the electronic main key.
Instruments and controls Operation Driving Instrument cluster display Interior equipment Practical hints Car care Technical data 180 Blocking of rear side window operation Synchronizing power windows If no operation of the rear side windows by switch (for instance by children) is desired, slide override switch (5) to the right; the N symbol becomes visible. If the power supply was interrupted, (battery disconnected or low), the windows cannot be opened or closed by the express feature.
Sliding/pop-up roof 1 Turn the electronic key in starter switch to position 1 or 2. To open, close, raise or lower the sliding/pop-up roof: Move the switch to resistance point in the required direction. 3 Release the switch when the roof has reached the required position. 2 4 Warning! When closing the sliding/pop-up roof, be sure that there is no danger of anyone being harmed by the closing procedure.
Instruments and controls Operation Driving Instrument cluster display Interior equipment Practical hints Car care Technical data 182 Express opening and closing of sliding/pop-up roof Warning! To select a sunroof opening position, press the switch to resistance point and release it when the sunroof has reached the required position. When closing the sliding/pop-up roof, be sure that there is no danger of anyone being harmed by the closing procedure.
Notes: The sliding/pop-up roof can also be opened and closed using the summer opening/convenience feature, see page 45. To avoid damaging the seals, do not transport any objects with sharp edges which can stick out of the sliding/pop-up roof. The sliding/pop-up roof can be opened or closed manually should an electrical malfunction occur, see page 369. P77.
Instruments and controls Operation Instrument cluster display Driving Interior equipment Practical hints Car care Technical data 184 Interior lighting 3 Right front reading lamp 2 1 5 Press the button to switch the right reading lamp (8) on or off. The right reading lamp in the rear view mirror will be switched on or off. 3 4 4 Door contact switch: Press the rocker switch.
Footwell lighting To prevent the vehicle battery from being discharged with doors open, all interior lamps switch off after approximately 5 minutes. With exterior lamps on, the driver and front passenger footwell is illuminated. 6 Interior lamps, front: Press rocker switch in to switch front interior and reading lamps on. The front interior lighting stays on while the rocker switch is pressed in. Center console lighting Turn the electronic key in the starter switch to position 1.
Instruments and controls Operation Driving Instrument cluster display Interior equipment Rear window sunshade (optional) Practical hints Car care Technical data 186 Always raise the sunshade fully for its support against the window frame. Warning! When operating the rear window sunshade, be sure that there is no danger of anyone being harmed by the raising or lowering procedure. The raising or lowering procedure can be immediately halted by briefly pressing the upper or lower half of the switch.
Sun visors Vanity mirrors 1 4 2 3 2 1 P68.60-2009-26 P68.00-2150-26 1 Illuminated vanity mirror Swing sun visors (2) down to protect against sun glare. If sunlight enters through a side window, disengage sun visor from the inner mounting (1) and pivot to the side, and slide it to the desired position. With the visor engaged in its inner mounting (2), the lamp (4) can be switched on by opening the cover (3). Slide the mirror to the left or right for a normal or magnified image.
Instruments and controls Operation Driving Instrument cluster display Interior equipment Practical hints Car care Technical data 188 Interior Storage compartments and armrests Warning! Warning! To help avoid personal injury during a collision or sudden maneuver, exercise care when stowing things. Put luggage or cargo in the trunk if possible. Do not pile luggage or cargo higher than the seat backs. Do not place anything on the shelf below the rear window. Keep compartment lids closed.
Glove box 1 Unlocked position 4 The glove box lid is equipped with a container (4) for coins and small accessories. 2 Locked position 3 Press to open To open, press the marking on the cover. The glove box can be locked and unlocked with the mechanical key. See page 29 for instructions on how to remove the mechanical key from the electronic main key (e.g. for valet parking service).
Instruments and controls Operation Driving Instrument cluster display Interior equipment Storage compartment in front of armrest 5 Storage compartment in front of armrest To open: Touch the top of the cover lightly. To close: Lightly push the cover up until it engages in lock. Practical hints Car care Technical data 190 Storage compartment below the front armrest A coin holder is also located in the storage compartment below the armrest.
Storage space below the armrest Storage compartment under the front seats To open: Press button (7) and raise the armrest. To close: Lower the armrest until it engages in lock. Notes: The storage compartment can be heated or cooled, see page 175. The compartment can get very warm due to its confined space. When storing heat sensitive objects in the compartment, close the air outlet while heating the passenger compartment. Do not obstruct the air outlet in the storage compartment.
Instruments and controls Operation Driving Instrument cluster display Interior equipment Storage compartments in the rear passenger compartment Practical hints Technical data Car care 192 Coat hooks 1 P68.70-2002-26 Opening the storage space: Slide the cover (10) back to open, forward to close. Coat hooks (1) are located on the headliner above the rear windows. To open: Briefly press indentation on coat hook – the coat hook folds down. To close: Push coat hook into headliner.
Cup holder Press button (2) to open the second cup holder. The cup holder opens automatically. 1 Cup holder in front seat armrest Open the storage compartment in front of the armrest, see page 190. Warning! To open: Briefly press button (1). The cup holder opens automatically. Interior equipment Instruments and controls Operation Keep the cup holder closed while traveling. Place only containers that fit into the cup holder to prevent spills.
Instruments and controls Operation Driving Instrument cluster display Interior equipment Practical hints Technical data Car care 194 4 To close: Fold second cup holder in direction of arrow (3) until it engages. Press button (4) to unlock cup holder and fold into the storage compartment until it engages. Close the storage compartment.
To open: Push front of sliding compartment – the cup holder slides out. To close: Push the sliding compartment back until it engages. Warning! Keep the cup holder closed while traveling. Place only containers that fit into the cup holder to prevent spills. Do not fill containers to a height where the contents could spill during vehicle maneuvers, especially hot liquids. 5 P91.
Instruments and controls Operation Driving Instrument cluster display Interior equipment Practical hints Car care Technical data 196 Ashtrays Center console To open: Briefly touch the mark on the cover, the ashtray opens automatically. To remove ashtray insert from center console: 1 Warning! Remove front ashtray only with vehicle standing still. With the gear selector lever in position “N”, turn off the engine and set the parking brake.
Rear seats To open: Briefly touch the top of the cover, the ashtray opens automatically. To remove the insert: Push down on catch (2) and pull out the ashtray insert. To install the insert: Position the insert and close the cover.
Instruments and controls Operation Driving Instrument cluster display Interior equipment Practical hints Car care Technical data 198 Lighter Turn the electronic key in starter switch to position 1 or 2. Push in lighter (1); it will pop out automatically when hot. Warning! Never touch the heating element or sides of the lighter, they are extremely hot, hold at knob only. 1 P68.20-2069-26 1 Center console lighter When leaving the vehicle always remove the electronic key from the starter switch.
Parcel net in trunk There are hooks (1) on the left and right inside the trunk from which the parcel net is suspended. The tab (arrow) must point down into the trunk. The parcel net and hooks are only designed to take light loads in normal driving conditions. They are unable to secure a load in the event of an accident. Observe the weight limit on the tab (arrow). 1 P68.
Instruments and controls Operation Driving Instrument cluster display Interior equipment Practical hints Car care Technical data 200 Cargo tie-down hooks Parcel net in front passenger footwell A small convenience parcel net is located in the front passenger footwell. It is for small and light items, such as road maps, mail, etc.. Warning! Do not place heavy or fragile objects, or objects having sharp edges, in the parcel net.
Telephone, general Bear in mind that at a speed of just 30 mph (approximately 50 km/h), your vehicle is covering a distance of approximately 50 feet (approximately 14 m) every second. Warning! A driver’s attention to the road must always be his/ her primary focus when driving. For your safety and the safety of others, we recommend that you pull over to a safe location and stop before placing or taking a telephone call.
Instruments and controls Operation Driving Garage door opener Instrument cluster display Practical hints Car care Technical data 202 Garage door opener The built-in remote control is capable of operating up to three separately controlled objects. Warning! When programming a garage door opener, the door moves up or down. When programming or operating the remote control make sure there is no possibility of anyone being harmed by the moving door.
For operation in the USA only: This device complies with Part 15, Subpart C, Section 209 of the FCC Rules. Operation is subject to the following two conditions: 3. Using both hands, simultaneously push the handheld transmitter button and the desired integrated remote control button. Do not release the buttons until completing step 4. (1) This device may not cause harmful interference, and 4. The indicator lamp on the integrated remote control will flash, first slowly and then rapidly.
Instruments and controls Operation Driving Instrument cluster display Garage door opener Rolling code programming: To train a garage door opener (or other rolling code devices) with the rolling code feature, follow these instructions after completing the “Programming” portion of this text. (A second person may make the following training procedures quicker and easier.) 1. Locate training button on the garage door opener motor head unit.
Operation of remote control: 1. Turn electronic key in starter switch to position 1 or 2. 1. Turn electronic key in starter switch to position 1 or 2. 2. Select and press the appropriate button to activate the remote controlled device. The integrated remote control transmitter continues to send the signal as long as the button is pressed – up to 20 seconds. 2.
Instruments and controls Operation Instrument cluster display Driving Infrared reflecting windshield 1 1 2 4 3 1 Mounting location for electronic toll collection devices (infrared transparent) 2 Infrared transparent area (pass-through for electronic signals) 4 19.0 in (48 cm) 5 1.75 in (4.5 cm) Technical data Your vehicle is equipped with infrared reflecting glass which reduces the amount of radiated heat entering the interior through the windows. 5 3 31.
Instruments and controls Operation Infrared reflecting windshield Driving Instrument cluster display Practical hints 207 Car care Technical data Index
Instruments and controls Operation Infrared reflecting windshield Driving Instrument cluster display Practical hints 208 Car care Technical data Index
Driving Control and operation of radio transmitters ...............................208 The first 1 000 miles (1 500 km) .................................209 Maintenance ...................................209 Tele Aid ........................................... 210 Catalytic converter ........................220 Emission control ............................221 Starter switch .................................222 Starter switch – KEYLESS-GO ......224 Starting and turning off the engine ........................
Instruments and controls Operation Driving Instrument cluster display Control and operation of radio transmitters Practical hints Car care Technical data 208 Control and operation of radio transmitters COMAND, radio and telephone Telephones and two-way radio Warning! Warning! Please do not forget that your primary responsibility is to drive the vehicle. Only operate the COMAND (Cockpit Management and Data System), radio or telephone1 if road and traffic conditions permit.
The first 1 000 miles (1 500 km) Maintenance The more cautiously you treat your vehicle during the break-in period, the more satisfied you will be with its performance later on. Therefore, drive your vehicle during the first 1 000 miles (1 500 km) at moderate vehicle and engine speeds. Approximately 30 days or 2000 miles (2000 km) prior to the next recommended service, the remaining distance or days are displayed in the multifunction indicator. See Flexible service system (FSS) on page 147.
Instruments and controls Operation Driving Instrument cluster display Tele Aid Practical hints Car care Technical data 210 Tele Aid Important! The initial activation of the Tele Aid system may only be performed by completing the subscriber agreement and placing an acquaintance call using the “SOS” button. Failure to complete either of these steps will result in a system that is not activated.
Important! Once the emergency call is in progress, the indicator lamp in the “SOS” button will begin to flash. The message “EMERGENCY CALL – CONNECTING CALL” appears in the multifunction display. When the connection is established, the message “EMERGENCY CALL – CALL CONNECTED” appears in the multifunction display. All information relevant to the emergency, such as the location of the vehicle (determined by the GPS satellite location system), vehicle model, identification number and color are generated.
Instruments and controls Operation Driving Instrument cluster display Tele Aid Practical hints Car care Technical data 212 The Tele Aid system is available if: • it has been activated and is operational. Activation requires a subscription for monitoring services and cellular air time • the relevant cellular phone network and GPS signals are available and pass the information on to the response center.
Initiating an emergency call manually 1 2 P82.95-2186-26 P82.95-2187-26 Briefly press on cover (1) – the cover will open. Press the SOS button (2) briefly (for longer than 2 seconds). The indicator lamp in the SOS button (2) will flash until the emergency call is concluded. Wait for a voice connection to the Response Center. Close the cover (1) after the emergency call is concluded.
Instruments and controls Operation Driving Instrument cluster display Tele Aid Practical hints Car care Technical data 214 Warning! If you feel at any way in jeopardy when in the vehicle (e.g. smoke or fire in the vehicle, vehicle in a dangerous road location), please do not wait for voice contact after you have pressed the emergency button. Carefully leave the vehicle and move to a safe location.
Notes: Information button ¡ The indicator lamp in the Roadside Assistance button • remains illuminated in red for approx. 10 seconds during the system self-check after turning electronic key in starter switch to position 2 (together with the “SOS” button and the Information button ¡). Located below the center armrest cover is the Information button ¡. Pressing and holding the button (for longer than 2 seconds) will initiate a call to the Client Assistance Center.
Instruments and controls Operation Driving Instrument cluster display Tele Aid Practical hints Car care Technical data 216 Notes: Important! The indicator lamp in the Information button ¡ remains illuminated in red for approx. 10 seconds during the system self-check after turning electronic key in starter switch to position 2 (together with the “SOS” button and the Roadside Assistance button •).
During this time you will hear a chirp and voice contact will be interrupted. Voice contact will resume once the retransmission is completed. Once a call is concluded, a chirp will be heard and the appropriate indicator lamp will stop flashing. The COMAND system operation will resume. Notes: The indicator lamp in the respective button flashes until the call is concluded.
Instruments and controls Operation Driving Instrument cluster display Tele Aid Practical hints Car care Technical data 218 Remote door unlock Notes: In the case you have your vehicle locked unintentionally (e.g. key inside vehicle), and the reserve key is not handy, contact the Mercedes-Benz Response Center at 1-800-756-9018 (in the USA) or 1-888-923-8367 (in Canada). You will be asked to provide your password which you provided when you completed the subscriber agreement.
Stolen vehicle tracking services Once information is available, the message “NEW INFO RECEIVED – READ LATER WHEN STOPPED?” will appear. Select “Yes”. With the vehicle stopped in a safe location press SVC, then select “View Info Service of mm.dd.yyyy hh.mm”. Messages will be retained for 30 minutes once the ignition is switched off. In the event your vehicle was stolen, report the incident to the police who will issue a numbered incident report. Pass this number on to the Mercedes-Benz Response Center.
Instruments and controls Operation Driving Instrument cluster display Catalytic converter Practical hints Car care Technical data 220 Catalytic converter Warning! Your Mercedes-Benz is equipped with monolithic type catalytic converters, an important element in conjunction with the oxygen sensors to achieve substantial control of the pollutants in the exhaust emissions.
Emission control Warning! Certain systems of the engine serve to keep the toxic components of the exhaust gases within permissible limits required by law. Inhalation of exhaust gas is hazardous to your health. All exhaust gas contains carbon monoxide, and inhaling it can cause unconsciousness and lead to death. These systems, of course, will function properly only when maintained strictly according to factory specifications.
Instruments and controls Operation Driving Instrument cluster display Starter switch Starter switch Practical hints Car care Technical data 222 1 Most electrical consumers can be operated. For detailed information see respective subjects. 2 Driving position. Gear selector lever is unlocked. 3 Starting position. See page 227 for instructions on starting and turning off the engine. See page 44 for instructions on the simultaneous use of the electronic key and the KEYLESS-GO-function.
Important! Notes: If the electronic key is left in the starter switch position 0 for an extended period of time, it can no longer be turned in the lock. In this case, remove electronic key from starter switch and reinsert. A warning sounds when the driver’s door is opened with the electronic key in starter switch position 1 or 0. Caution! It is therefore recommended that you turn off unnecessary electrical consumers while driving in stopand-go traffic.
Instruments and controls Operation Driving Instrument cluster display Starter switch — KEYLESS-GO Start-/Stop button (vehicles with KEYLESS-GO) Practical hints Car care Technical data 224 Warning! When leaving the vehicle always take the electronic key and the KEYLESS-GO-card with you, and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause serious personal injury.
Important! “On” position (starter switch position 1, see page 222). Most electrical consumers can be operated. For detailed information see respective subjects. For the KEYLESS-GO-system to function properly, the operator should observe the following: Operation/driving position (starter switch position 2, see page 222). All electrical consumers can be operated. Gear selector is unlocked. • If the KEYLESS-GO-card is positioned farther away from the vehicle (e.g.
Instruments and controls Operation Driving Instrument cluster display Starter switch — KEYLESS-GO • Do not forget, the engine can be started by anyone if a KEYLESS-GO-card is left inside the vehicle. • To be able to operate the vehicle in the case of a malfunction in the KEYLESS-GO-system (e.g. strong radio frequency disturbance), we recommend that you carry the electronic key plus mechanical key with you and keep them in a safe place so that they are always handy.
Starting and turning off the engine After several unsuccessful attempts, have the system checked at the nearest authorized Mercedes-Benz Center. Before starting Important! Ensure that parking brake is engaged and that selector lever is in position “P” or “N”. Starting Due to the installed starter non-repeat feature, the electronic key must be turned completely to the left before attempting to start the engine again.
Instruments and controls Operation Driving Instrument cluster display Starting and turning off the engine Turning off Turning off the engine with electronic key: Put the selector lever in position “P” and turn the electronic key in the starter switch to position 0 to stop the engine. The electronic key can only be removed with the selector lever in position “P”. Turning off the engine with KEYLESS-GO: Stop the vehicle and put the selector lever in position “P”.
Automatic transmission The automatic transmission selects individual gears automatically, dependent upon • Selector lever position, see page 232 • Program mode selector, see page 236 • Accelerator position • Vehicle speed The gear shifting process is continuously adapted, dependent on the driving style, the driving situation and the road characteristics.
Instruments and controls Operation Driving Instrument cluster display Automatic transmission Practical hints Car care Technical data 230 Driving Important! The selector lever is automatically locked while in position “P”. To move the selector lever out of position “P”, the service brake pedal must be firmly depressed before the shift lock will release.
Stopping Rocking a vehicle free in this manner may cause the ABS or traction system malfunction indicator lamp to come on. Turn off and restart the engine to clear the malfunction indication. For brief stops, e.g. at traffic lights, leave the transmission in gear and hold vehicle with the service brake. For longer stops with the engine idling, shift into “N” or “P” and hold the vehicle with the service brake.
Instruments and controls Operation Driving Instrument cluster display Automatic transmission Selector lever position Practical hints Car care Technical data 232 Park position The park position is to be used when parking the vehicle. Engage only with the vehicle stopped. The park position is not intended to serve as a brake when the vehicle is parked. Rather, the driver should always use the parking brake in addition to placing the selector lever in park to secure the vehicle.
Neutral Gear selection for special circumstances No power is transmitted from the engine to the drive axle. When the brakes are released, the vehicle can be moved freely (pushed or towed). Do not engage “N” while driving except to coast when the vehicle is in danger of skidding (e.g. on icy roads, see page 246 for winter driving instructions).
Instruments and controls Operation Driving Instrument cluster display Automatic transmission Press and hold selector lever in the æ direction: The transmission will shift from the current gear directly to gear range “D”. Warning! On slippery road surfaces, never downshift in order to obtain braking action. This could result in drive wheel slip and reduced vehicle control. Your vehicle’s ABS will not prevent this type of loss of control.
Gear ranges: Upshift through 2nd gear only. For driving in mountainous regions or under extreme operating conditions. This gear selection will allow use of the engine’s braking power when descending steep grades. Upshift through 4th gear only. Suitable for performance driving. Upshift through 3rd gear only. Suitable for moderately steep hills. Since the transmission does not shift higher than 3rd gear, this gear selection will allow use of the engine’s braking power downhill.
Instruments and controls Operation Driving Instrument cluster display Automatic transmission Program mode selector switch Practical hints Car care Technical data 236 S Standard mode Press switch on symbol “S”. Use this mode for all regular driving. The vehicle starts out in 1st gear.
W Emergency operation (Limp home mode) Winter/Wet (snow and ice) mode Press switch on symbol “W”. The vehicle starts out in 2nd gear, except with selector lever in 1st gear, or with accelerator pedal in kick-down position. If vehicle acceleration worsens or the transmission no longer shifts, the transmission is most likely operating in Limp Home Mode which engages when there is a malfunction of the transmission.
Instruments and controls Operation Parking brake Parking brake Driving Instrument cluster display Practical hints Car care Technical data 238 To engage, firmly depress parking brake pedal. When the electronic key is in starter switch position 2, the brake warning lamp in the instrument cluster should come on brightly. To release the parking brake, pull handle on instrument panel. The brake warning lamp in the instrument cluster should go out.
Driving instructions Drinking and driving Drive sensibly – save fuel Warning! Fuel consumption, to a great extent, depends on driving habits and operating conditions. Drinking or taking drugs and driving can be a very dangerous combination. Even a small amount of alcohol or drugs can affect your reflexes, perceptions and judgement. To save fuel you should: The possibility of a serious or even fatal accident is sharply increased when you drink or take drugs and drive.
Instruments and controls Operation Driving Instrument cluster display Driving instructions Practical hints Car care Technical data 240 Pedals Brakes Warning! Warning! Keep driver’s foot area clear at all times. Objects stored in this area may impair pedal movement.
Caution! Have the brake system inspected at an authorized Mercedes-Benz Center immediately. When driving down long and steep grades, relieve the load on the brakes by shifting into a lower gear to use the engine’s braking power. This helps prevent overheating of the brakes and reduces brake pad wear. All checks and service work on the brake system should be carried out by an authorized Mercedes-Benz Center. Install only brake pads and brake fluid recommended by Mercedes-Benz.
Instruments and controls Operation Driving Instrument cluster display Driving instructions Practical hints Car care Technical data 242 Parking Important! Warning! It is advisable to set the parking brake whenever parking or leaving the vehicle. In addition, move selector lever to position “P”. To reduce the risk of personal injury as a result of vehicle movement, before turning off the engine and leaving the vehicle always: 1. Keep right foot on service brake pedal. 2.
Tires Warning! Do not allow your tires to wear down too far. As tread depth approaches 1/16 in (1.5 mm), the adhesion properties on a wet road are sharply reduced. Warning! If you feel a sudden significant vibration or ride disturbance, or you suspect that possible damage to your vehicle has occurred, you should turn on the hazard warning flashers, carefully slow down, and drive with caution to an area which is a safe distance from the roadway.
Instruments and controls Operation Driving Instrument cluster display Driving instructions Practical hints Car care Technical data 244 Aquaplaning Warning! Depending on the depth of the water layer on the road, aquaplaning may occur, even at low speeds and with new tires. Reduce vehicle speed, avoid track grooves in the road and apply brakes cautiously in the rain. If ice has formed on the road, tire traction will be substantially reduced.
Tire speed rating Exceeding the maximum speed for which tires are rated can lead to sudden tire failure causing loss of vehicle control and resulting in personal injury and possible death. CL 500 and CL 600: Your vehicle is factory equipped with “H”-rated tires, which have a speed rating of 130 mph (210 km/h). Vehicles with Sport Package: Your vehicle is factory equipped with “Y”-rated tires, which have a speed rating of 188 mph (300 km/h).
Instruments and controls Operation Driving Instrument cluster display Driving instructions Winter driving instructions The most important rule for slippery or icy roads is to drive sensibly and to avoid abrupt acceleration, braking and steering maneuvers. Do not use the cruise control system under such conditions. When the vehicle is in danger of skidding, move selector lever to position “N”. Try to keep the vehicle under control by corrective steering action.
Winter driving • Test battery: Battery capacity drops with decreasing ambient temperature. A well charged battery helps to ensure that the engine can be started, even at low ambient temperatures. Have your vehicle winterized at your authorized Mercedes-Benz Center before the onset of winter. • Change the engine oil if the engine contains an oil which is not approved for winter operation. For viscosity (SAE/CCMC class) and filling quantity, see page 395.
Instruments and controls Operation Driving Instrument cluster display Driving instructions Practical hints Car care Technical data 248 Deep water Passenger compartment Caution! Warning! Do not drive through flooded areas or water of unknown depth. Always fasten items being carried as securely as possible.
Block heater (Canada only) Traveling abroad The engine is equipped with a block heater. Abroad, there is a widely-spread Mercedes-Benz service network at your disposal. If you plan to travel into areas which are not listed in the index of your Mercedes-Benz Center directory, you should request pertinent information from your authorized Mercedes-Benz Center. The electrical cable may be installed at your authorized Mercedes-Benz Center.
Instruments and controls Operation Driving Instrument cluster display Driving systems Practical hints Car care Technical data 250 Cruise control 2 Decelerate and set: Depress lever briefly to set speed. Hold lever down to decelerate. 1 Normally the vehicle is accelerated to the desired speed with the accelerator. Speed is set by briefly pushing the lever to position 1 or 2. The accelerator can then be released.
3 Canceling 4 Resume To cancel the cruise control, briefly push lever to position 3. If the lever is briefly pushed to position 4 when driving at a speed exceeding approx. 25 mph (40 km/h), the vehicle resumes the speed which was set prior to the cancellation of the cruise control. When you step on the brake pedal or the vehicle speed drops below approx. 25 mph (40 km/h), for example when driving upgrade, the cruise control will be canceled. The selected speed is shown for approx.
Instruments and controls Operation Driving Instrument cluster display Driving systems Practical hints Car care Technical data 252 Warning! Notes: Only use the cruise control if the traffic and weather conditions make it advisable to travel at a steady speed. If the engine does not brake the vehicle sufficiently while driving on a downgrade, the speed you set on the cruise control may be exceeded. In this case the automatic transmission shifts down (max.
Distronic (DTR) (optional) Any given speed between 25 mph (Canada: 30 km/h) and 110 mph (Canada: 180 km/h) can be maintained with the Distronic by operating the control lever on the steering column. When activated the Distronic system increases driving convenience, for example over long distances, as it automatically maintains a speed set by the driver by actively regulating the throttle setting. It also maintains within certain limitations a preset distance to a vehicle ahead.
Instruments and controls Operation Driving Instrument cluster display Driving systems Practical hints Car care Technical data 254 Note: Warning! For operation in the USA only: This device complies with Part 15, Subpart C, Section 209 of the FCC Rules. Operation is subject to the following two conditions: Only use Distronic if the traffic and weather conditions make it advisable to travel at a steady speed.
3 Canceling 1 To cancel Distronic, briefly push lever to position 3. The last set speed remains stored in memory. 4 Resume 3 • If the lever is briefly pulled to position 4 when driving at a speed above approx. 25 mph (Canada: 30 km/h), the vehicle resumes the speed which was selected prior to the cancellation of Distronic. 4 • For minor increases of speeds in increments of 1 mph (Canada: 1 km/h) – briefly pull lever to position 4.
Instruments and controls Operation Driving Instrument cluster display Driving systems Practical hints Car care Technical data 256 Activation of Distronic • Speed is set by briefly moving the control lever to position 1 or 2. The stored speed is displayed in the multifunction display for approx. 5 seconds (see also page 266), and one or two segments around the stored speed light up on the speedometer dial (see also page 267). • Remove foot from the accelerator.
• For a more precise setting the speed can be increased in increments of 1 mph (Canada: 1 km/h) by briefly pulling the control lever in direction (4). Invalid attempts to activate The multifunction display will show “–––” during invalid attempts to activate Distronic: • below a speed of approx.
Instruments and controls Operation Driving Instrument cluster display Driving systems Practical hints Car care Technical data 258 Deactivation of Distronic • the gear selector lever is moved to position “N”, Briefly move the distronic control lever in “OFF” direction (3) – the stored speed remains in the memory until the electronic key in the starter switch is turned to position 1 or 0.
Driving with Distronic activated from the speed of the vehicle in front up to your vehicle’s selected speed. See also page 266 for notes on the multifunction displays. Warning! Distronic brakes (up to 20% of vehicle braking power) the vehicle to restore the preset distance or to maintain the speed. The brake pedal is automatically retracted as this happens. Keep driver’s foot area clear at all times, including the area under the brake pedal.
Instruments and controls Operation Driving Instrument cluster display Driving systems Practical hints Car care Technical data 260 Warning! Caution! A continuous warning sounds and the distance warning lamp in the speedometer dial is illuminated if the Distronic system calculates that the distance to the vehicle ahead and your vehicle’s current speed indicate that Distronic will not be capable of slowing the vehicle sufficiently to maintain the preset following distance, which creates a danger of
Additional driving hints The driver must always be on the alert and observe all traffic and intercede with steering and braking inputs as necessary. Warning! Distronic works to maintain the speed selected by the driver unless a moving obstacle proceeding directly ahead of it in the same travel direction is detected (e.g. following another vehicle ahead at a distance set by Distronic). This means that: Important! When starting the engine, Distronic goes through an initialization and self-test phase.
Instruments and controls Operation Driving Instrument cluster display Driving systems Traveling through turns or bends in the roadway may result in Distronic detecting a moving vehicle traveling in front but not in your lane of travel, causing your vehicle to brake late or unexpectedly. You must be prepared to intercede with accelerator or brake application as necessary.
A vehicle changing lanes at close range is only recognized when entering the area scanned by Distronic. You must apply the service brakes to gain sufficient distance to the vehicle ahead. Driving systems Instruments and controls A narrow vehicle (e.g. a motorcycle) is only recognized when entering the area scanned by Distronic. You must apply the service brakes to gain sufficient distance to the vehicle ahead.
Instruments and controls Operation Driving Instrument cluster display Driving systems Practical hints Car care Technical data 264 Distance notification function Important! Even if Distronic is deactivated, the distance to the vehicle ahead continues to be measured, see page 266 for multifunction display. With the Distronic switched off, only the distance notification function operates, meaning the vehicle does not slow down.
• Decrease distance – turn thumbwheel (2) towards ®. Distronic settings Warning! It is up to the driver to exercise discretion to select the appropriate setting given road conditions, traffic, driver’s preferred driving style and applicable laws and driving recommendations for safe following distance. To switch the distance notification function on or off: To switch on – press upper half of switch (1). The indicator lamp in the switch lights up. To switch off – press lower half of the switch (1).
Instruments and controls Operation Driving Instrument cluster display Driving systems Practical hints Car care Technical data 266 Multifunction displays 1 Distronic is deactivated. The actual distance (5) and the should-be distance (6) to the vehicle ahead (4) are displayed. 2 Distronic is activated. The display shows the selected speed for approx. 5 seconds. 4 3 Distronic is activated. The message “DTR OFF” appears for approx. 5 seconds when Distronic is being deactivated.
Displays in the speedometer dial When Distronic system is activated, one or two segments around the speed stored in memory light up in the speedometer dial. If a vehicle is detected ahead, those segments in the speedometer dial light up that indicate the speed range from the speed of the vehicle in front up to the Distronic stored speed. When the vehicle in front can no longer be detected, only the segments around the stored speed light up. The vehicle is accelerated to the stored speed.
Instruments and controls Operation Driving Instrument cluster display Driving systems Practical hints Car care Technical data 268 Brake assist system (BAS) Applying the brakes very quickly results in maximum BAS assistance. Warning! To receive the benefit of the system you must apply continuous full braking power during the stopping sequence. Do not reduce brake pedal pressure.
Antilock brake system (ABS) At the instant one of the wheels is about to lock up, a slight pulsation can be felt in the brake pedal, indicating that the ABS is in the regulating mode. Keep firm and steady pressure on the brake pedal while experiencing the pulsation. Warning! Do not pump the brake pedal, rather use firm, steady brake pedal pressure. Pumping the brake pedal defeats the purpose for ABS and significantly reduces braking effectiveness.
Instruments and controls Operation Driving Instrument cluster display Driving systems ABS control The ABS malfunction indicator lamp - in the instrument cluster comes on with the electronic key in starter switch position 2 and should go out with the engine running. When the ABS malfunction indicator lamp in the instrument cluster comes on while the engine is running, it indicates that the ABS has detected a malfunction and has switched off.
Electronic stability program (ESP) Important! If the ESP warning lamp v flashes: Warning! • During take-off apply as little throttle as possible. ESP cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded. The ESP cannot prevent accidents, including those resulting from excessive speed in turns, or aquaplaning. Only a safe, attentive, and skillful driver can prevent accidents.
Instruments and controls Operation Driving Instrument cluster display Driving systems Notes: The yellow ESP warning lamp v in the speedometer dial comes on with the electronic key in starter switch position 2. It should go out with the engine running. If the ESP warning message is displayed, a malfunction has been detected in the system. Only partial engine output will be available. Have the ESP checked at your authorized Mercedes-Benz Center as soon as possible. For ESP warning message, see page 303.
ESP control switch To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, switch off ESP by pressing the upper half (1) of the ESP switch. The ESP warning lamp v, located in the speedometer dial, is continuously illuminated. Warning! When the ESP warning lamp is illuminated continuously, the ESP is switched off. Adapt your speed and driving to the prevailing road conditions.
Instruments and controls Operation Driving Instrument cluster display Driving systems Notes: Avoid spinning of one drive wheel. This may cause serious damage to the drive train which is not covered by the Mercedes-Benz Limited Warranty. The ESP warning lamp, located in the speedometer dial, starts to flash at any vehicle speed as soon as the tires lose traction and the wheels begin to spin.
Active body control (ABC) The maximum suspension range is selected automatically according to the selected ABC mode (1 or 2), road condition, and driving style. The selected suspension style is stored in memory, even with the electronic key removed from the starter switch. Suspension for regular driving style This is the setting for general driving. The system is set to regular driving mode when the indicator lamp (3) is not illuminated.
Instruments and controls Operation Driving Instrument cluster display Driving systems Level control system Practical hints Car care Technical data 276 The vehicle chassis ride height is raised or lowered automatically according to the selected setting and to the vehicle speed. This helps to increase vehicle handling safety and lowers fuel consumption. The selected setting is stored in memory, even with the electronic key removed from the starter switch.
Level control switch positions Normal level Normal level – indicator lamps (3, 4) are not illuminated. To change from raised level options I or II, press lower half of switch (2) once respectively twice. Used for normal operation of the vehicle. Speed dependent lowering of vehicle chassis (approximate values): Raise level, option I – indicator lamp (3) is illuminated. To change from normal level, press upper half (1) of switch. To change from raised level, option II, press lower half (2) of switch.
Instruments and controls Operation Driving Instrument cluster display Driving systems Practical hints Car care Technical data 278 Raised level, option I Raised level, option II This setting should be used when road surface conditions are rough and must be used when driving with snow chains mounted. This setting should be used when road surface conditions are very rough for increased ground clearance.
Parking assist (Parktronic) Warning! The Parktronic system assists the driver during parking maneuvers. It visually and audibly indicates the relative distance between the vehicle and an obstacle. Parktronic is a supplemental system. It is not intended to nor does it replace the need for extreme care. The responsibility during parking and other critical maneuvers rests always with the driver. The front area of the vehicle is monitored when driving forward.
Instruments and controls Operation Instrument cluster display Driving Parking system Practical hints Car care Technical data 280 Sensors A total of 10 sensors (1) monitor the vehicle’s front and rear areas. Six sensors are located in the front bumper, four sensors in the rear bumper. For proper operation of the Parktronic always keep the sensors clean, especially at times of snow and ice. See page 378 for instructions on cleaning the sensors in the bumpers.
Warning indicators Visual and audible signals indicate to the driver the relative distance between the vehicle and an obstacle. Warning indicators for the front area are located above the left and center air outlets in the dashboard. Warning indicators for the rear area are integrated in the rear headliner. 1 2 The frames (1) are illuminated when the Parktronic is engaged. Each warning indicator has 6 yellow and 2 red segments.
Instruments and controls Operation Driving Instrument cluster display Parking system Practical hints Car care Technical data 282 Monitoring reach of sensors Front bumper: Center approx. 40 in (100 cm) Corner approx. 24 in (60 cm) Rear bumper: Center approx. 48 in (120 cm) Corner approx. 32 in (80 cm) The first yellow segment lights up at these distances. Additional segments light up as the vehicle comes closer to the obstacle.
Parktronic switch The obstacle may not be recognized if outside the shaded sensor field, and no longer be indicated when approaching it any closer (warning indicators go out). Parktronic malfunction All red segments of the warning indicators light up, and a warning sounds for 3 seconds, if Parktronic does not function properly. The indicator lamp in the switch lights up and the system switches off automatically! 3 A dirty sensor could be the reason.
Instruments and controls Operation Driving Instrument cluster display What you should know at the gas station Practical hints Car care Technical data 284 What you should know at the gas station Open flap by briefly pushing near rear (arrow) and folding up. Turn fuel cap to the left and hold on to it until possible pressure in tank has been released, then remove cap. Failure to remove slowly could result in personal injury.
Engine oil Leaving the engine running and the fuel cap open can cause the “CHECK ENGINE” lamp to illuminate, see page 290 for notes on the “CHECK ENGINE” lamp. Checking oil level, see instructions on pages 154 and 331. Fuel tank capacity approx. 23.2 US gal (88.0 l). This includes approx. 2.9 US gal (11.0 l) reserve. Use premium unleaded gasoline: CL 500, CL 55 AMG: Posted Octane Index 91 (Average of 96 RON/86 MON). CL 600: Posted Octane Index 93 (Average of 98 RON/88 MON).
Instruments and controls Operation Driving Instrument cluster display What you should know at the gas station Practical hints Car care Technical data 286 Tire pressure Bulbs For tire pressure, refer to tire pressure label inside the fuel filler flap. See page 345 for further details.
Check regularly and before a long trip 1 Windshield washer and headlamp cleaning system For refilling reservoir see page 334. 2 Coolant level, see “Coolant level” on page 333 3 Engine oil level, see “Engine oil level, checking” on page 154 and 331 4 Brake fluid, see “Brake fluid” on page 395 Opening hood, see page 328. Vehicle lighting: Check function and cleanliness. For replacement of light bulbs, see “Exterior lamps” on page 354. P20.00-2057-26 Exterior lamp switch, see page 156.
Instruments and controls Operation Driving Check regularly and before a long trip Instrument cluster display Practical hints 289 Car care Technical data Index
Instrument cluster display Malfunction and indicator lamps in the instrument cluster ....................290 On-board diagnostic system .....290 Check engine malfunction indicator lamp .............................290 Brake warning lamp ..................292 Supplemental restraint system (SRS) indicator lamp .............................293 Fuel reserve warning .................293 ABS malfunction indicator lamp .............................294 Electronic stability program (ESP) — warning lamp .............
Instruments and controls Operation Driving Instrument cluster display Malfunction and indicator lamps Malfunction and indicator lamps in the instrument cluster General information: If a bulb in the instrument cluster fails to light up during the bulb self-check when turning the electronic key in starter switch to position 2, have it checked and replaced if necessary.
may still drive the vehicle, however, in all cases, we recommend that you have the system checked at your authorized Mercedes-Benz Center as soon as possible. With some exceptions, the control module switches off the “CHECK ENGINE” malfunction indicator lamp if the condition, causing the lamp to come on, no longer exists during three consecutive cycles. If the “CHECK ENGINE” lamp comes on continuously and/or the vehicle is not driving normally (e.g.
Instruments and controls Operation Driving Instrument cluster display Malfunction and indicator lamps Brake warning lamp Except Canada Canada only When the brake warning lamp and message appear while the engine is running, this means: Practical hints Car care Technical data 292 Warning! Driving with the brake warning lamp illuminated can result in an accident. Have your brake system checked immediately if the brake warning lamp stays on. Don’t add brake fluid before checking the brake system.
Supplemental restraint system (SRS) indicator lamp Fuel reserve warning The operational readiness of the airbag system is verified by the indicator lamp “SRS” in the instrument cluster when turning the electronic key in starter switch to position 1 or 2. If no fault is detected, the lamp will go out after approximately 4 seconds; after the lamp goes out, the system continues to monitor the components and circuitry of the airbag system and will indicate a malfunction by coming on again.
Instruments and controls Operation Driving Instrument cluster display Malfunction and indicator lamps ABS malfunction indicator lamp The ABS malfunction indicator lamp in the instrument cluster comes on with the electronic key in starter switch position 2 and should go out with the engine running.
Electronic stability program (ESP) — warning lamp Distronic (DTR) – warning lamp The yellow ESP warning lamp in the speedometer dial comes on with the electronic key in starter switch position 2. It should go out with engine running. With the electronic key in starter switch position 2, the distance warning lamp in the speedometer dial comes on and goes out with the engine running.
Instruments and controls Operation Driving Instrument cluster display Malfunction and indicator lamps Seat belt nonusage warning lamp With the electronic key in starter switch position 2, the seat belt nonusage warning lamp comes on, and a warning sounds for a short time if the driver’s seat belt is not fastened. After starting the engine, the seat belt nonusage warning lamp blinks for a brief period to remind the driver and passengers to fasten seat belts.
Malfunction and warning messages in the multifunction display Note: Certain malfunction and warning messages are accompanied by an audible signal. Malfunction and warning messages in red are always accompanied by an audible signal. Malfunction and warning messages for the following systems will be displayed immediately in the multifunction display. They are divided into three categories. Temporary messages such as “TRUNK OPEN!” will not be stored in the malfunction message memory.
Instruments and controls Operation Driving Instrument cluster display Malfunction and warning messages Practical hints Car care Technical data Index 298 DISPLAY DEFECTIVE (engine control unit) DISPLAY DEFECTIVE (several systems) Line 1 Line 2 C* Line 1 Line 2 C* DISPLAY DEFECTIVE VISIT WORKSHOP! 2 DISPLAY DEFECTIVE VISIT WORKSHOP! 2 * C = Category, see page 297 * C = Category, see page 297 This message is displayed to indicate that the information being relayed by the engine contro
BATTERY /ALTERNATOR This message indicates a malfunction which must be repaired immediately. It may indicate that the poly-V-belt has broken. Should this condition occur, the poly-V-belt must be replaced before continuing to operate the vehicle. Otherwise, the engine will overheat due to an inoperative water pump which may result in damage to the engine. Do not continue to drive the vehicle with this message displayed.
Instruments and controls Operation Driving Instrument cluster display Malfunction and warning messages Practical hints Car care Technical data Index 300 ENTRANCE POSITION BRAKE ASSIST Line 1 Line 2 C* Line 1 Line 2 C* ENTRANCE POSITION DO NOT DRIVE! 1 BRAKE ASSIST VISIT WORKSHOP! 2 * C = Category, see page 297 * C = Category, see page 297 Wait until the seat and steering wheel have moved to their driving positions. The display will clear when they have done so.
BRAKE LINING WEAR BRAKE FLUID Line 1 Line 2 C* Line 1 Line 2 C* BRAKE LINING WEAR VISIT WORKSHOP! 2 BRAKE FLUID VISIT WORKSHOP! 2 * C = Category, see page 297 * C = Category, see page 297 When this message appears during braking, it indicates that the brake pads are worn down. Warning! Driving with this message displayed can result in an accident. Have your brake system checked immediately. Don’t add brake fluid before checking the brake system.
Instruments and controls Operation Driving Instrument cluster display Malfunction and warning messages Practical hints Technical data Index 302 PARKING BRAKE TRUNK OPEN Line 1 Line 2 C* Line 1 PARKING BRAKE RELEASE BRAKE! 1 TRUNK OPEN! * C = Category, see page 297 Car care * C = Category, see page 297 Line 2 C* 2
ELEC. STABIL. PROG. (Electronic stability program) 1 The display or the system is malfunctioning. 2 A malfunction has been detected in the system. Pressing the accelerator pedal will require greater effort. Only partial engine output will be available. 3 The enhanced vehicle stability offered by ESP and the torque reduction feature are unavailable. 4 This message may be displayed if the power supply was interrupted (battery disconnected or empty). Synchronize ESP, see page 272.
Instruments and controls Operation Driving Instrument cluster display Malfunction and warning messages Practical hints Car care Technical data 304 COOLANT (coolant level) The low engine coolant level warning should not be ignored. Extended driving with the symbol displayed may cause serious engine damage not covered by the Mercedes-Benz Limited Warranty. In cases of major or frequent minor coolant loss, have the cooling system checked at your authorized Mercedes-Benz Center as soon as possible.
COOLANT (coolant temperature) During severe operating conditions and stop-and-go city traffic, the coolant temperature may rise close to the red marking. The engine should not be operated with the coolant temperature in the red zone. Doing so may cause serious engine damage which is not covered by the Mercedes-Benz Limited Warranty.
Instruments and controls Operation Driving Instrument cluster display Malfunction and warning messages Practical hints Car care Technical data Index 306 LIGHTING SYSTEM Line 1 Line 2 C* L. TURN SIG. RFLECTR CHECK LAMP! 2 R. TURN SIG.
Line 1 Line 2 C* FRONT FOGLAMP, R CHECK LAMP! 2 In the case of bulb failures in certain lamps, other lamps will substitute. See page 354 for instructions on replacing bulbs. REAR FOGLAMP CHECK LAMP! 2 * C = Category, see page 297 REVERSE LIGHT, L CHECK LAMP! 2 1 The display or the system is malfunctioning. REVERSE LIGHT, R CHECK LAMP! 2 2 The brake lamps are switching on after a delay or are permanently on – visit workshop immediately.
Instruments and controls Operation Driving Instrument cluster display Malfunction and warning messages Practical hints Car care Technical data Index 308 SEAT BELT SYSTEM LIGHT SENSOR Line 1 Line 2 C* Line 1 Line 2 C* LIGHT SENSOR VISIT WORKSHOP! 2 SEAT BELT SYSTEM VISIT WORKSHOP! 2 * C = Category, see page 297 The headlamps will be switched on automatically if the light sensor malfunctions.
TELEPHONE – FUNCTION Line 1 Line 2 C* Line 1 Line 2 C* FUNCTION NOT AVAILABLE! 3 CRUISE CONTROL VISIT WORKSHOP!1 2 * C = Category, see page 297 * C = Category, see page 297. The display appears if button í or ì on the multifunction steering wheel is pressed and the vehicle is not equipped with a telephone. 1 Cruise control is malfunctioning.
Instruments and controls Operation Driving Instrument cluster display Malfunction and warning messages Practical hints Car care Technical data 310 ACTIVE BODY CONTROL (ABC) 2 The capability of the system is restricted. Important! Line 1 Line 2 C* DISPLAY DEFECTIVE VISIT WORKSHOP!1 2 ACTIVE BODY CONTROL DRIVE CAREFULLY!2 1 ACTIVE BODY CONTROL STOP, CAR TOO LOW!3 1 ACTIVE BODY CONTROL VISIT WORKSHOP!4 2 * C = Category, see page 297 1 The display or the system is malfunctioning.
3 The ABC is defective. Stop the vehicle. Press upper half of level control switch, see page 276 - system selects raised level mode. The vehicle chassis is raised depending on the kind of defect. 4 The capability of the system is restricted. Important! When the message “ACTIVE BODY CONTROL – VISIT WORKSHOP!” appears, do not exceed a speed of 50 mph (80 km/h). Visit your Mercedes-Benz Center as soon as possible.
Instruments and controls Operation Driving Instrument cluster display Malfunction and warning messages Technical data Car care Index 312 TIRE PRESSURE Line 1 Practical hints Line 2 C* TIRE PRESSURE, FL CAUTION TIRE DEFECT!1 1 TIRE PRESSURE, FR CAUTION TIRE DEFECT!1 1 TIRE PRESSURE, RL CAUTION TIRE DEFECT!1 1 TIRE PRESSURE, RR CAUTION TIRE DEFECT!1 1 TIRE PRESSURE, FL CHECK TIRES!2 1 TIRE PRESSURE, FL CHECK TIRES!4 2 TIRE PRESSURE, FR CHECK TIRES!2 1 4 TIRE PRESSURE CAUTI
4 Tire pressure in one or more tires is low. Check and correct tire pressure, see page 345. Warning! Do not drive with a flat tire. A flat tire affects the ability to steer or brake the vehicle. You may lose control of the vehicle. Continued driving with a flat tire will cause excessive heat build-up and possibly a fire. 5 The tire pressure monitor cannot be activated with the engine running. Turn off the engine and repeat activation, see page 151.
Instruments and controls Operation Driving Instrument cluster display Malfunction and warning messages Practical hints Car care Technical data 314 ENGINE OIL LEVEL 3 There is a risk of damaging the engine or catalytic converter. The engine oil level must be checked immediately. See Engine oil level indicator on page 154. 4 The engine oil level has dropped to a critical level. Check the engine oil level immediately.
SEAT BACKREST Warning! Line 1 Line 2 C* SEAT BEACKREST, LEFT LOCK! 1 SEAT BEACKREST, RIGHT LOCK! 1 The seat belts provide protection only with the backrest locked in place and, therefore, must be locked in place with the vehicle in motion. Do not drive the vehicle when the backrest is not locked in place. If the warning message “SEAT BACKREST, LEFT – LOCK!” or “SEAT BACKREST, RIGHT – LOCK!” is displayed in the multifunction display, then the respective backrest is not engaged in its lock.
Instruments and controls Operation Driving Instrument cluster display Malfunction and warning messages Practical hints Car care Technical data Index 316 KEY DOOR P54.30-2245-21 Line 1 Line 2 C* Line 1 REPLACE KEY1 VISIT WORKSHOP! 2 DOOR OPEN! AUTOM. LIGHT ON REMOVE KEY! 1 * C = Category, see page 297. * C = Category, see page 297. 1 Key needs possibly to be replaced.
TELE AID HOOD P54.30-2560-21 Line 1 Line 2 C* Line 1 Line 2 C* ENGINE HOOD OPEN! 2 TELE AID VISIT WORKSHOP!1 1 * C = Category, see page 297. 1 The Tele Aid system consists of three types of response; automatic and manual emergency, roadside assistance and information. With this message displayed, one or more functions may not be available. See page 328 for hood. See page 210 for notes on the Tele Aid.
Instruments and controls Operation Driving Instrument cluster display Malfunction and warning messages Practical hints Car care Technical data 318 CHIP-CARD (KEYLESS-GO) 1 Check battery of KEYLESS-GO-card, see page 366. 2 The KEYLESS-GO-card cannot be recognized by the running engine (e.g. strong radio-frequency interference) or the card is not in the vehicle.
SELECTOR LEVER (Vehicles with KEYLESS-GO only) Malfunction and warning messages Instruments and controls Operation Place selector lever in position “P”. The message appears when attempting to turn off the engine while the selector lever is in any other position than “P”, see page 228.
Instruments and controls Operation Driving Instrument cluster display Malfunction and warning messages Car care Technical data 320 WASHER FLUID When this message appears while the engine is running, the level of the reservoir has dropped to approx. 1/3 of the total volume.
DISTRONIC (DTR) 1 The display or the system is malfunctioning. 2 Due to the presence of electro-magnetic radiation, the system is presently unavailable. 3 Distronic is automatically switched off. Distronic sensor in hood grille needs cleaning, see page 378. 4 Distronic is defective. Line 1 Line 2 C* DISPLAY DEFECTIVE VISIT WORKSHOP!1 2 DISTRONIC EXTERNAL MALFUNCTION!2 2 DISTRONIC MALFUNCTION CLEAN SENSOR!3 2 DISTRONIC VISIT WORKSHOP!4 2 * C = Category, see page 297.
Practical hints First aid kit .....................................324 Fuses ................................................325 Shelf below rear window ..............327 Hood .................................................328 Checking engine oil level .............331 Automatic transmission fluid level ...................................332 Active body control (ABC) fluid level ........................332 Coolant level ...................................333 Adding coolant ...........................
Instruments and controls Operation Driving Instrument cluster display First aid kit Practical hints Car care Technical data 324 First aid kit 1 The first aid kit is located in the rear seat armrest (1). To open: Press handle (2) upwards and fold the lid (3) up. Remove the first aid kit. To close: Fold the lid (3) down until it engages.
Fuses Fuse boxes in the engine compartment Most of your vehicle’s electrical components are fused with safety fuses. With the exception of the brake lights, all individual lighting system components are electronically fused. Before replacing a blown safety fuse, determine the cause of the short circuit. Always observe amperage and color of fuse. The circuit for components is protected by a cycled circuit breaker interrupted if too much current is being drawn.
Instruments and controls Operation Instrument cluster display Driving Fuses Practical hints Car care Technical data 326 To close the fuse box: Ensure that the sealing rubber is properly positioned when you replace the cover. Press the cover down by hand. Slide both tabs (3) back to the ‹ symbol on the fuse box. 2 Note: 3 3 The fuse box cover must be properly positioned and both tabs pushed forward to prevent moisture entering the fuse box. P54.
Shelf below rear window Auxiliary fuse box below rear seat Warning! The shelf below the rear window should not be used to carry objects. This will avoid such objects from being thrown about and injuring vehicle occupants during an accident or sudden maneuver. The trunk is the preferred place to carry objects. 4 4 Auxiliary fuse box below right rear seat. To open: Remove the cover. To close: Press the cover on.
Instruments and controls Operation Driving Instrument cluster display Engine compartment Hood Warning! To help prevent personal injury, stay clear of moving parts when the hood is open and the engine is running. Be sure the hood is properly closed before driving. When closing hood, use extreme caution not to catch hands or fingers. The radiator fan may continue to run for approximately 30 seconds or even restart after the engine has been turned off. Stay clear from fan blades.
To open: Pull handle (2) to its stop out of radiator grill and open hood (do not pull up on the handle). To unlock the hood, pull release lever (1) under the driver’s side of the instrument panel. At the same time a handle will extend out of the radiator grill. Note: To avoid damage to the windshield wipers or hood, open the hood only with the wipers in the parked position.
Instruments and controls Operation Driving Instrument cluster display Engine compartment Practical hints Car care Technical data 330 To close: 3 3 Lower the hood and let it drop into lock from a height of approx. 1 ft. (30 cm), assisting with hands placed flat on edges of hood (3). To avoid hood damage, please make sure that hood is fully closed. If not, repeat closing procedure. Do not push down on hood to attempt to fully close it.
Checking engine oil level 2 2 1 P18.40-2067-26 P18.40-0287-26 CL 600 CL 500 1 Dipstick Model CL 500 and CL 55 AMG Model CL 600: The dipstick is omitted. Engine oil level can be checked via the engine oil level indicator, see page 154. To check the engine oil level, park vehicle on level ground, with engine at normal operational temperature. Check engine oil level approximately 5 minutes after stopping the engine, allowing for the oil to return to the oil pan.
Instruments and controls Operation Driving Instrument cluster display Engine compartment Practical hints Car care Technical data 332 The engine oil level can be checked by either the oil dipstick or via the multifunction display in the instrument cluster, see page 154. See malfunction and warning messages on page 297 if an engine oil level display appears on the multifunction display when the engine is running. Wipe the oil dipstick clean prior to checking the engine oil level.
Adding coolant Coolant level If coolant has to be added, a 50/50 mixture of water and MB anticorrosion/antifreeze should be added. Warning! • In order to avoid possibly serious burns: Use extreme caution when opening the hood if there are any signs of steam or coolant leaking from the cooling system, or if the coolant temperature gauge indicates that the coolant is overheated. 1 • Do not remove pressure cap on coolant reservoir if engine temperature is above 194°F (90°C).
Instruments and controls Operation Driving Instrument cluster display Engine compartment Practical hints Car care Technical data 334 Windshield and headlamp washer system Warning! Washer solvent/antifreeze is highly flammable. Do not spill washer solvent/antifreeze on hot engine parts, because it may burn. You can be seriously burned. 1 Windshield and headlamp washer fluid mixing ratio For temperatures above freezing: MB Windshield Washer Concentrate “S” and water.
Spare wheel, vehicle tools, storage compartment Lift trunk floor and engage handle in upper edge of trunk. Always lower trunk floor before closing trunk lid. To remove the spare wheel: Take out the vehicle tool kit tray. Turn the luggage bowl counterclockwise and remove the spare wheel. 2 To store spare wheel: Place spare wheel in wheel well and secure it with luggage bowl. Turn luggage bowl clockwise to its stop. 4 1 3 Place vehicle tool kit tray in luggage bowl. P40.
Instruments and controls Operation Driving Instrument cluster display Jack Practical hints Car care Technical data 336 Jack Storing the jack in the trunk: Retract the jack arm to the base of the jack, push the crank handle up and turn counterclockwise to the end of the stop (storage position). Warning! P58.10-2001-26 To prepare the jack for use: Remove the jack from the spare wheel well under the trunk floor, push the crank handle up and turn clockwise until it engages (operational position).
Wheels It is imperative that the wheel mounting bolts be fastened to a tightening torque of 110 ft.lb. (150 Nm) whenever wheels are mounted. Replace rims or tires with the same designation, manufacturer and type as shown on the original part. See your authorized Mercedes-Benz Center for further information. For rim and tire specifications, refer to “Technical Data”. Warning! See your authorized Mercedes-Benz Center for information on tested and recommended rims and tires for summer and winter operation.
Instruments and controls Operation Driving Instrument cluster display Tires, Wheels Practical hints Car care 338 Rotating wheels Spare wheel The wheels can be rotated according to the degree of tire wear while retaining the same direction of travel.
Spare wheel CL 55 AMG and Sport Package For rim and tire specifications, refer to “Technical Data”. Important! Warning! The spare wheel rim size is 71/2 J x 17 H 2 with tire size 225/55 R17 97H. The spare wheel rim is for temporary use only. Use for over a total of 12 000 miles (20 000 km) (aggregate of all uses) may cause wheel rim failure leading to an accident and possible injuries.
Instruments and controls Operation Driving Instrument cluster display Tires, Wheels Changing wheels Warning! The jack is designed exclusively for jacking up the vehicle at the jack tubes built into either side of the vehicle. To help avoid personal injury, use the jack only to lift the vehicle during a wheel change. Never get beneath the vehicle while it is supported by the jack. Keep hands and feet away from the area under the lifted vehicle.
P40.10-2177-26 4. Remove the two-piece wheel wrench from the vehicle tool kit and assemble. Using the wrench, loosen but do not yet remove the wheel bolts. 5. Remove the protective cover from the jack support tube opening by inserting the screwdriver (supplied in the tool kit) in the opening and prying it out. The tube openings are located directly behind the front wheel housings and in front of the rear wheel housings.
Instruments and controls Operation Driving Instrument cluster display Tires, Wheels Practical hints Car care Technical data 342 P40.10-2178-26 6. Insert jack arm fully into the tube hole up to the stop. Place jack on firm ground. Position the jack so that it is always vertical (plumb-line) as seen from the side (see arrow), even if the vehicle is parked on an incline. 7. Jack up the vehicle until the wheel is clear of the ground. Never start engine while vehicle is raised. P40.10-2179-26 8.
P40.10-2264-26 P40.10-2263-26 10. Clean contact surfaces of wheel and wheel hub. Install spare wheel on wheel hub. Insert wheel bolts and tighten them slightly. 11. Lower vehicle. Remove jack and insert jack tube cover. To avoid paint damage, place wheel flat against hub and hold it there while installing first wheel bolt. Unscrew the alignment bolt to install the last wheel bolt.
Instruments and controls Operation Driving Instrument cluster display Tires, Wheels Practical hints Car care Technical data 344 Warning! Always replace wheel bolts that are damaged or rusted. Never apply oil or grease to wheel bolts. Damaged wheel hub threads should be repaired immediately. Incorrect mounting bolts or improperly tightened mounting bolts can cause the wheel to come off. This could cause an accident. Be sure to use the correct mounting bolts. P40.10-2265-26 Warning! 12.
Tire inflation pressure Tire pressures listed for light loads are minimum values offering high driving comfort. Increased inflation pressures for heavy loads produce favorable handling characteristics with lighter loads and are perfectly permissible. The ride of the vehicle, however, will become somewhat harder. A table (see fuel filler flap) lists the tire inflation pressures specified for Mercedes-Benz recommended tires as well as for the varying operating conditions.
Instruments and controls Operation Driving Instrument cluster display Tires, Wheels The spare tire should be checked periodically for condition and inflation. Spare tire will age and become worn over time even if never used, and thus should be inspected and replaced when necessary. Warning! Do not overinflate tires. Overinflating tires can result in sudden deflation (blowout) because they are more likely to become punctured or damaged by road debris, potholes etc..
The service life of the battery is dependent on its condition of charge. The battery should always be kept sufficiently charged, in order to last an optimum length of time. Therefore, we strongly recommend that you have the battery charge checked frequently, and corrected if necessary, especially if you use the vehicle less than approximately 200 miles (300 km) per month, mostly for short distance trips, or if it is not used for long periods of time.
Instruments and controls Operation Driving Instrument cluster display Battery Practical hints Car care Technical data 348 While the engine is running the battery terminal clamps must not be loosened or detached, otherwise the generator and other electronic components would be damaged. Battery recycling Batteries contain materials that can harm the environment with improper disposal. Large 12 Volt storage batteries contain lead.
Jump starting Important! A discharged battery can freeze at approx. +14°F (–10°C). In that case, it must be thawed out before jumper cables are used. Attempting to jump start a frozen battery can result in it exploding, causing personal injury. Warning! Failure to follow these directions will cause damage to the electronic components, and can lead to a battery explosion and severe injury or death. Never lean over batteries while connecting or jump starting, you might get injured.
Instruments and controls Operation Driving Instrument cluster display Jump starting Practical hints Car care Technical data 350 Proceed as follows: 1. Position the vehicle with the charged battery so that the jumper cables will reach, but never let the vehicles touch. Make sure the jumper cables do not have loose or missing insulation. 2. On both vehicles: • Turn off engine and all lights and accessories, except hazard warning flashers or work lights.
Towing the vehicle Important! When towing the vehicle, please, note the following: Warning! With the automatic central locking activated and the electronic key in starter switch position 2 (vehicles with KEYLESS-GO: in “On” position, see page 224), the vehicle doors lock if the left front wheel as well as the right rear wheel are turning at vehicle speeds of approx. 9 mph (15 km/h) or more.
Instruments and controls Operation Driving Instrument cluster display Towing the vehicle Practical hints Car care Technical data 352 2 1 Cover on right side of front bumper 2 Cover right side of rear bumper To remove cover: To remove cover: Press mark on cover in direction of arrow and lift cover off to reveal threaded hole for towing eye bolt. The towing eye bolt is supplied with the tool kit (located in trunk in spare wheel). Screw towing eye bolt in to its stop and tighten with lug wrench.
We recommend that the vehicle be transported using flat bed equipment. This method is preferable to other types of towing. Warning! With the engine not running, there is no power assistance for the braking and steering systems. In this case, it is important to keep in mind that a considerably higher degree of effort is necessary to brake and steer the vehicle. Important! To prevent damage during transport, do not tie down vehicle by its chassis or suspension parts.
Instruments and controls Operation Driving Instrument cluster display Exterior lamps Practical hints Car care Technical data 354 Exterior lamps Replacing bulbs Headlamp adjustment Warning! Correct headlamp adjustment is extremely important. Check and readjust headlamps at regular intervals and when a bulb has been replaced. Because of high voltage in Xenon lamps, it is dangerous to replace the bulb or repair the lamp and its components.
Headlamp assembly 4 2 1 3 5 P82.10-2197-26 P82.10-2198-26 1 Headlamp cover for high beam headlamp, parking and standing lamp 2 Electrical connector for high beam headlamp bulb Warning! 4 Bulb holder for turn signal lamp Do not remove cover (5) for Xenon headlamp. Because of high voltage in Xenon lamps, it is dangerous to replace the bulb or repair the lamp and its components. We recommend that you have such work done by a qualified technician.
Instruments and controls Operation Driving Instrument cluster display Exterior lamps Bulbs for high beam H7 (55 W) Open hood. Press the clip together (arrow) and remove headlamp cover (1). Pull electrical connector off. Unclip the retainer spring and take out the bulb. Insert the new bulb so that the base locates in the recess on the holder. Clip in retainer springs and plug the connector onto the bulb. Align headlamp cover (1) and click into place.
Turn signal lamp (1156 NA [26.9/5 W/32/4cp]) Parking and standing lamp H 6W Open hood. Open hood. Twist bulb holder (4) counterclockwise and pull out. Push bulb into socket, turn counterclockwise and remove. Press the clip together (arrow) and remove headlamp cover (1). Remove the bulb socket (3). Push bulb into socket, turn counterclockwise and remove. Insert new bulb in socket, push in and twist clockwise. Reinstall bulb socket. Insert new bulb in socket, push in and twist clockwise.
Instruments and controls Operation Driving Instrument cluster display Exterior lamps Practical hints Car care Technical data 358 Taillamp assemblies Open trunk lid. Turn lock (6) counterclockwise and fold trim to the side. Twist bulb socket counterclockwise and pull out. Push bulb into socket, turn counterclockwise and remove. Insert new bulb in socket, push in and twist clockwise. Reinstall bulb socket. Reinstall trim and secure with lock (6). 6 P82.
7 Black socket: Backup lamp (1156 [32 cp] bulb) 7 8 10 8 Red socket Driver’s side: Taillamp/parking lamp/rear fog lamp (P 21/4W bulb) Passenger side: Taillamp/parking lamp (P 21/4W bulb) 9 9 Grey socket: Taillamp/parking lamp/standing lamp/side marker (67 [4 cp] bulb) 10 White socket: Turn signal lamp (1156 NA bulb [yellow]) Exterior lamps Instruments and controls 359 Operation Driving Instrument cluster display Practical hints Car care Technical data Index
Instruments and controls Operation Driving Instrument cluster display Exterior lamps License plate lamp Practical hints Car care Technical data 360 Side marker lamp, front (5 W/4 cp bulb) 1 2 P82.10-2634-26 Loosen both securing screws (1), remove lamp and replace tubular lamp (C 5 W/4 cp). Carefully slide lamp towards rear (arrow 1), and remove front end first (arrow 2). Twist bulb socket counterclockwise and pull out. Remove bulb from socket. Insert new bulb in socket.
Stop lamp, High mounted stop lamp, Additional turn signals on the exterior mirror Standby bulb function The rear fog lamp, dimmed, will act as a replacement lamp, if the bulb in the inner left-hand taillamp stops working. The stop lamps, the high mounted stop lamp (3rd brake lamp), and the additional turn signals on the exterior mirrors are equipped with LEDs. The inner taillamp acts as a replacement for the right or left-hand bulb of the outer taillamp, if it stops working as a parking lamp.
Instruments and controls Operation Driving Instrument cluster display Exterior lamps Low beam, switchable for left- or right-hand drive Practical hints Car care Technical data 362 Driving in countries with left-hand traffic requires the headlamps to be switched over accordingly. 1 Asymmetric low beam (right-hand traffic) 2 Symmetric low beam (left-hand traffic) Turn lever to the respective position until it locks in place.
Changing batteries in the electronic main key 2 1 3 4 P80.20-2201-26 P80.35-2029-26 1 Transmit buttons Changing batteries 2 Lamp for battery check and function control Move locking tab (3) in direction of right arrow and remove mechanical key (4, left arrow). Checking batteries If one of the transmit buttons (1) is pressed, the battery check lamp (2) lights up briefly – indicating that the batteries are in order. Change batteries if the battery check lamp (2) does not light up briefly.
Instruments and controls Operation Driving Instrument cluster display Electronic main key Practical hints Technical data Car care 364 7 8 5 4 6 P80.35-2025-26 Insert mechanical key (4) in side opening (5) to open latch. Press briefly (do not use mechanical key as lever) to release battery compartment. Remove mechanical key from side opening. Carefully remove battery compartment in direction of arrow (6). P80.
Important! Synchronizing remote control Batteries contain materials that can harm the environment if disposed of improperly. Recycling of batteries is the preferred method of disposal. For disposal, please follow manufacturer’s recommendation on battery package. The remote control may have to be resynchronized, if the vehicle cannot be locked or unlocked. To synchronize insert electronic key in starter switch. The remote control should once again be operational.
Instruments and controls Operation Instrument cluster display Driving KEYLESS-GO-card Practical hints Car care Technical data 366 Changing batteries in the KEYLESS-GO-card 2 Checking batteries Briefly press button (1). The indicator lamp “Unlock driver’s door” (2) or “Global Unlock” (3) should come on red or green. 3 Change batteries if indicator lamps do not illuminate, see page 367. 1 P80.
Changing batteries Important! Batteries contain materials that can harm the environment if disposed of improperly. Recycling of batteries is the preferred method of disposal. For disposal, please follow manufacturer’s recommendation on battery package. Replacement batteries: Lithium, type CR 2025 or equivalent. Pry open cover (1) (e.g. by using a narrow blade screw driver) and remove batteries. Install new batteries as indicated by the “+” and “-” markings in the KEYLESS-GO-card.
Instruments and controls Operation Driving Instrument cluster display Emergency engine shut-down Emergency engine shut-down Practical hints Car care Technical data 368 Fuel filler flap, manual release If the engine can no longer be stopped using the electronic key or the start-/stop button (vehicles with KEYLESS-GO), the engine can be turned off by withdrawing two fuses.
Emergency operation of sliding/pop-up roof 2 1 P77.00-2022-26 P77.00-2023-26 The sliding/pop-up roof can be opened or closed manually should an electrical malfunction occur. Obtain crank (2) (supplied with vehicle) and insert through hole. The sliding/pop-up roof drive is located behind the lens of the left interior overhead light. To slide roof closed or to raise the roof at the rear: turn crank clockwise. Pry off the interior light lens (1) using a screwdriver.
Instruments and controls Operation Driving Instrument cluster display Replacing wiper blades Replacing wiper blades Practical hints Car care Technical data 370 • Turn electronic key in starter switch to position 1. • Turn combination switch to position I, see page 160. • With wiper arms in position shown above, turn electronic key in starter switch to position 0.
Trunk lamp The trunk lamp will switch off after approximately 10 minutes if the trunk lid is left open. 3 4 2 1 P82.30-2089-26 Removal: Fold the wiper arm (1) forward and turn the wiper blade (2) at a right-angle to wiper arm. Remove wiper blade from wiper arm. Installation: Install wiper blade onto the wiper arm by inserting pin (4) into take-up (3). Rotate wiper blade into position parallel to wiper arm.
Instruments and controls Operation Roof rack Driving Instrument cluster display Practical hints Car care Technical data 372 Roof rack Use only those roof racks approved by Mercedes-Benz to avoid damage to the vehicle. Follow manufacturer’s installation instructions. Only mount roof racks on the retrofitted mounting points (see arrows). Mounting a roof rack requires a one-time installation of take-up points.
Vehicle care Cleaning and care of the vehicle ............................. 374 Power washer ..............................375 Tar stains ..................................... 376 Paintwork, painted body components ................................. 376 Engine cleaning .......................... 376 Vehicle washing ......................... 376 Contents - Vehicle care Instruments and controls Operation Ornamental moldings ............... 377 Headlamps, taillamps, turn signal lenses ......................
Instruments and controls Operation Driving Instrument cluster display Cleaning and care of the vehicle Cleaning and care of the vehicle Warning! Many cleaning products can be hazardous. Some are poisonous, others are flammable. Always follow the instructions on the particular container. Always open your vehicle’s doors or windows when cleaning the inside. Never use fluids or solvents that are not designed for cleaning your vehicle.
Power washer Scratches, corrosive deposits, corrosion or damage due to negligent or incorrect care cannot always be removed or repaired with the car-care products recommended here. In such cases it is best to seek aid at your authorized Mercedes-Benz Center. When using a power washer for cleaning the vehicle always observe manufacturer’s operating instructions.
Instruments and controls Operation Driving Instrument cluster display Cleaning and care of the vehicle Practical hints Car care Technical data 376 Tar stains Engine cleaning Quickly remove tar stains before they dry and become more difficult to remove. A tar remover is recommended. Prior to cleaning the engine compartment make sure to protect electrical components and connectors from the intrusion of water and cleaning agents.
Ornamental moldings Due to the width of the vehicle, prior to running the vehicle through an automatic car wash, fold back the outside mirrors to prevent them from getting damaged. For regular cleaning and care of very dirty chromeplated parts, use a chrome cleaner. In the winter, thoroughly remove all traces of road salt as soon as possible. Headlamps, taillamps, turn signal lenses When washing the underbody, do not forget to clean the inner sides of the wheels.
Instruments and controls Operation Driving Instrument cluster display Cleaning and care of the vehicle Cleaning the Distronic system sensor Practical hints 378 Cleaning the parktronic system sensors 1 Use a mild car wash detergent, such as Mercedes-Benz approved Car Shampoo, with plenty of water to clean the sensor (1). To prevent scratches, never apply strong force and use only a soft, non-scratchy cloth when cleaning the sensor. Do not attempt to wipe dirty sensors with a dry cloth or sponge.
Wiper blades To prevent damage to the hood or the wipers, the wiper arms should only be folded forward in the position shown above. • Turn electronic key in starter switch to position 1. • Turn combination switch to position I, see page 160. • Once the wiper arms are in the position shown above, turn key in starter switch to position 0. Note: For safety reasons, remove electronic key from starter switch before cleaning the wiper blades, otherwise the wiper motor can suddenly turn on and cause injury.
Instruments and controls Operation Driving Instrument cluster display Cleaning and care of the vehicle Practical hints Car care Technical data 380 Window cleaning Light alloy wheels Use a window cleaning solution on all glass surfaces. An automotive glass cleaner is recommended. Mercedes-Benz approved Wheel Care should be used for regular cleaning of the light alloy wheels.
Instrument cluster Cup holder Use a gentle dishwashing detergent or mild detergent for delicate fabrics as a washing solution. Wipe with a cloth moistened in lukewarm solution. Do not use scouring agents. Use a gentle dishwashing detergent or mild detergent for delicate fabrics as a washing solution. Wipe with a cloth moistened in lukewarm solution. Do not use scouring agents.
Instruments and controls Operation Driving Instrument cluster display Cleaning and care of the vehicle Practical hints Car care Technical data 382 Seat belts Leather upholstery The webbing must not be treated with chemical cleaning agents. Use only clear, lukewarm water and soap. Do not dry the webbing at temperatures above 176°F (80°C) or in direct sunlight. Using aftermarket seat covers or wearing clothing that have the tendency to give off coloring (e.g. when wet etc.
Technical data Spare parts service ........................384 Warranty coverage .........................384 Identification labels .......................385 Layout of poly-V-belt drive ............387 Technical data ................................388 Fuels, coolants, lubricants etc. - capacities .......393 Engine oils ......................................395 Contents - Technical data Instruments and controls Operation Engine oil additives ...................... 395 Air conditioner refrigerant .......
Instruments and controls Operation Driving Instrument cluster display Technical data Practical hints Car care Technical data 384 Spare parts service Warranty coverage All authorized Mercedes-Benz Centers maintain a stock of original spare parts required for maintenance and repair work. In addition, strategically located parts distribution centers provide quick and reliable parts service.
Identification labels 2 Vehicle Identification Number (VIN) (below right rear passenger seat) 1 Certification label (below driver’s door lock latch) Technical data Instruments and controls 385 Operation Driving Instrument cluster display Practical hints Car care Technical data Index
Instruments and controls Operation Driving Instrument cluster display Technical data Practical hints Car care Technical data 386 3 Engine number 4 VIN, visible (lower edge of windshield) 5 Emission control label 6 Information label, California version Vacuum line routing for emission control system When ordering spare parts, please specify vehicle identification and engine numbers. P61.
Layout of poly-V-belt drive 6 7 8 1 4 5 3 CL 600 CL 500, CL 55 AMG 1 Automatic belt tensioner 5 Generator (alternator) 2 Crankshaft 6 Idler pulley 3 Air conditioner compressor 7 Power steering pump 4 Coolant pump 8 Idler pulley (CL 600 only) Technical data Instruments and controls 2 387 Operation Driving Instrument cluster display Practical hints Car care Technical data Index
Instruments and controls Operation Driving Instrument cluster display Technical data Practical hints Car care Technical data 388 Technical data Model CL 500 (215.3751) CL 55 AMG (215.3731) CL 600 (215.3781) Engine 113 113 137 Mode of operation 4-stroke engine, gasoline injection 4-stroke engine, gasoline injection 4-stroke engine, gasoline injection No. of cylinders 8 8 12 Bore 3.82 in (97.00 mm) 3.82 in (97.00 mm) 3.31 in (84.00 mm) Stroke 3.31 in (84.00 mm) 3.60 in (92.
Rims – Tires Model CL 500, CL 600 (except Sport Package) Model Rims (light alloy) Wheel offset: 71/2 J x 17 H 2 1.81 in (46 mm) All season tires: Radial-ply tires Rims front axle AMG light alloy rims Wheel offset: 81/2 J x 18 H 2 1.73 in (44 mm) 225/55 R17 97H Rims rear axle AMG light alloy rims Wheel offset: 91/2 J x 18 H 2 1.
Instruments and controls Operation Driving Instrument cluster display Technical data Practical hints Car care Technical data 390 Rims – Winter tires Model CL 55 AMG Rims front axle AMG light alloy rims Wheel offset: 8 /2 J x 18 H 2 1.73 in (44 mm) Rims rear axle AMG light alloy rims Wheel offset: 91/2 J x 18 H 2 1.81 in (46 mm) Radial-ply tires front axle rear axle 245/45 R18 96Y 1 275/40 R18 99Y M02, 3 1 Spare wheel Rim (light alloy) Wheel offset: 71/2 J x 17 H 2 1.
Electrical system Model CL 500 CL 55 AMG CL 600 Generator (alternator) 14 V/150 A 14 V/150 A 14 V/150 A Starter motor 12V/1.7 kW 12V/1.7 kW 12V/2.2 kW Battery 12V/100 Ah 12V/100 Ah 12V/100 Ah Spark plugs Bosch F 8 DPER Beru 14 FGH 8 DPUR X 2 NGK PFR 5 R-11 0.039 in (1.0 mm) 15 – 22 ft.lb (20 – 30 Nm) Bosch F 8 DPER Beru 14 F 7-DPUR X 2 0.039 in (1.0 mm) 15 – 22 ft.lb (20 – 30 Nm) 0.041 in (1.05 mm) 15 – 22 ft.
Instruments and controls Operation Driving Instrument cluster display Technical data Practical hints Car care Technical data 392 Main Dimensions Model CL 500 CL 55 AMG CL 600 Overall vehicle length 196.6 in (4993 mm) 196.6 in (4993 mm) 196.6 in (4993 mm) Overall vehicle width 73.1 in (1857 mm) 73.1 in (1857 mm) 73.1 in (1857 mm) Overall vehicle height 54.9 in (1394 mm) 54.9 in (1394 mm) 54.9 in (1394 mm) Wheel base 113.6 in (2885 mm) 113.6 in (2885 mm) 113.
Fuels, coolants, lubricants etc. - capacities Vehicle components and their respective lubricants must match. Therefore use only brands tested and recommended by us. Please refer to the Factory Approved Service Products pamphlet, or inquire at your Mercedes-Benz Center. Model Engine with oil filter Fuels, coolants, lubricants etc. CL 500 8.5 US qt (8.0 l) CL 55 AMG 8.0 US qt (7.5 l) CL 600 10.0 US qt (9.5 l) Recommended engine oils Automatic transmission 9.6 US qt (9.
Instruments and controls Operation Driving Instrument cluster display Fuels, coolants, lubricants etc. - capacities Model Fuel tank including a reserve of Car care Technical data 394 Capacity Fuels, coolants, lubricants etc. 23.2 US gal (88.0 l) 2.9 US gal (11.0 l) Premium unleaded gasoline: Posted Octane 91 (Avg. of 96 RON/86 MON) 7.1 US qt (6.
Engine oils Air conditioner refrigerant Engine oils are specifically tested for their suitability in our engines. Therefore, use only engine oils recommended by Mercedes-Benz. Information on recommended brands is available at your authorized Mercedes-Benz Center. R-134a (HFC) refrigerant and special PAG lubricating oil is used in the air conditioner system. Never use R-12 (CFC) or mineral-based lubricating oil, otherwise damage to the system will occur.
Instruments and controls Operation Driving Instrument cluster display Fuels, coolants, lubricants etc. - capacities Practical hints Car care Technical data 396 Premium unleaded gasoline Fuel requirements Caution! Use only Premium unleaded meeting ASTM standard D 439: To maintain the engine’s durability and performance, premium unleaded gasoline must be used.
Gasoline additives Coolants A major concern among engine manufacturers is carbon build up caused by gasoline. Mercedes-Benz recommends the use of only quality gasoline containing additives that prevent the build up of carbon deposits.
Instruments and controls Operation Driving Instrument cluster display Fuels, coolants, lubricants etc. - capacities the engine temperature will increase due to the lower heat transfer capability of the solution. Therefore, do not use more than this amount of anticorrosion/antifreeze. If the coolant level is low, water and MB anticorrosion/ antifreeze should be used to bring it up to the proper level (have cooling system checked for signs of leakage).
Consumer information may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate. This has been prepared as required of all manufactures of passenger cars under Title 49, Code of U.S. Federal Regulations, Part 575 pursuant to the “National Traffic and Motor Vehicle Safety Act of 1966”. Traction The traction grades, from highest to lowest are AA, A, B, and C.
Instruments and controls Operation Driving Instrument cluster display Consumer information Practical hints Car care Technical data 400 Temperature Warning! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Index Aquaplaning .................................................................. 244 Armrest, rear bench .......................................................195 Ashtrays ...........................................................................196 Center console, front ................................................196 Rear seats ...................................................................197 Audio systems .................................................................
Instruments and controls Operation Driving Instrument cluster display Index Practical hints Car care Technical data 402 Residual engine heat utilization ............................ 174 Special settings ......................................................... 169 Switching on and off ................................................ 175 Windows fogged on the inside ................................ 170 Windows fogged on the outside .............................. 171 Automatic transmission ...........
COOLANT (coolant temperature) malfunction and warning messages ..................... 305 Coolant level Adding ........................................................................ 333 Checking .................................................................... 333 Coolant temperature gauge .......................................... 117 Coolants .......................................................................... 397 Anticorrosion/antifreeze quantity ........................ 398 Courtesy lighting .
Instruments and controls Operation Driving Instrument cluster display Index Practical hints Car care Technical data 404 Display illumination .......................................................116 Distronic (DTR) ...................................................... 133, 253 Activation of Distronic .............................................256 Additional driving hints .......................................... 261 Cleaning sensor ........................................................
Side marker lamp, front .......................................... 360 Standing lamps ......................................................... 357 Taillamp assemblies ................................................ 358 Turn signal lamp ...................................................... 357 Exterior mirror adjustment ..........................................107 Exterior mirror, front passenger side, parking position ........................................................
Instruments and controls Operation Driving Instrument cluster display Index Practical hints Car care Technical data 406 See CHECK ENGINE malfunction indicator lamp ................................290 Fuel filler flap, manual release ...................................368 Fuel requirements .........................................................396 Fuel reserve warning ....................................................293 Fuels, coolants, lubricants etc. - capacities ...............
Convenience feature ...................................................45 Keys, vehicle .....................................................................28 See individual settings ............................................ 140 Instrument cluster ..........................................................114 Activating ....................................................................116 Instrument cluster illumination ...................................116 Instrument lamps ..........................
Instruments and controls Operation Driving Instrument cluster display Index Practical hints Car care Technical data 408 Locking and unlocking ............................................ 36, 40 Low engine coolant level warning ..............................304 Lumbar support ............................................................... 74 M Maintenance ...................................................................209 Malfunction and indicator lamps in the instrument cluster .................
O Cassette player .......................................................... 127 CD Player .................................................................... 126 Distronic (DTR) .......................................................... 133 Engine oil level indicator .........................................124 FSS ..............................................................................124 Individual settings ....................................................
Instruments and controls Operation Driving Instrument cluster display Index Practical hints Car care Technical data 410 Express opening and closing .................................. 179 Opening and closing ..................................................45 Synchronizing ........................................................... 180 Problems with your vehicle ........................................... 14 Product information ..........................................................
SRS malfunction ...............................................................92 Standby bulb function ...................................................361 Start lock-out .....................................................................32 Electronic main key ....................................................32 KEYLESS-GO-card .......................................................32 Starter switch .........................................................
Instruments and controls Operation Driving Instrument cluster display Index Practical hints Car care Technical data 412 T Tachometer ......................................................................119 Technical data ................................................................388 Electrical system ....................................................... 391 Main dimensions ......................................................392 Rims and tires ..............................................
W Trunk lid Emergency release ..................................................... 61 Trunk lid release switch .................................................57 TRUNK OPEN malfunction and warning messages ......................302 Turn signal failure ......................................................... 160 Turn signals .................................................................... 160 Turning off the engine Electronic main key ..................................................228 KEYLESS-GO .
Service and Literature Your authorized Mercedes-Benz Center has trained technicians and original Mercedes-Benz parts to service your vehicle properly. For expert advice and quality service, see your authorized Mercedes-Benz Center. If you are interested in obtaining service literature for your vehicle, please contact your authorized Mercedes-Benz Center. We consider this the best way for you to obtain accurate information for your vehicle.
Order No. 65152136 13 Part No.
