Installation & Assembly

ManualsBrandsMercer41 ManualsCeiling LightsGrandville 4-Light Unique / Statement Geometric Chandelier

1of3

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

EstimatedAssemblyTime:30-45 minutes

Preparation:Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomer service for replacement

parts.

Note:This CONVERTIBLEfixturecanbemountedaspendantlightorsemi-flushlight.Refertorespective

installationsteps forinstallations.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject

glass parts to any shock while in operation or shattering may result.

LightSource:(4)CandelabraBase60WMaximum.

Assembly Instructions for Pendant Light

(Step 1A - Step 7A)

Hardware Contents

Package Contents

Crossbar Assembly

Supply Wires

and Ground

Wire

Figure 2A

6” Rod

Ceiling Canopy

12” Rod

Socket

Assembly

Swivel

Hex Nut

Flat

Washer

Nipple

STEP 1A Attach Swivel and Ceiling

Canopy together

A. Thread Nipple (F) onto the Swivel (D).

B. Place Ceiling Canopy (A) and Flat

Washer (G) over the Nipple (F), secure

by threading Hex Nut (E) onto the

Nipple (F), tighten until sung.

Figure 1A

STEP 2A - Install Ceiling Canopy, Rods and Socket Assembly

together

A. Determine the Rods (B/C) to be assembled to the Socket Assembly

(H) according to your

hanging height.

B. Pass the supply wires

and ground wire

through the chosen

rods (B/C) and the

Ceiling Canopy (A).

Thread the Socket

Assembly (H), the

chosen Rods (B/C)

and the Ceiling

Canopy (A) together.

Hand tighten until

snug.

Suggested rods for

Ceiling height :

8’ ceiling : use (2) 12”

rods

9’ ceiling : use (2) 6”

rods and (2) 12” rods

STEP 3A Install Crossbar Assembly-

A. Pass the supply wires through the Crossbar

Assembly (AA). Attach the Crossbar

Assembly (AA) to the Outlet Box with the

head of the Green Ground Screw facing

you. Secure it with Outlet Box Screws (not

included). Tighten until snug.

Figure 3A

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

STEP 4A Fit Ceiling Canopy to Crossbar Assembly-

Ceiling Canopy A to the

Ceiling Canopy A

ceiling

Remove mounting balls from the Crossbar Assembly (AA). Fit the

( ) Crossbar Assembly (AA) and secure with

mounting balls. Note: The ( ) should be snug

against the and the mounting balls. If Not, adjust the length of

the nipple on the Crossbar Assembly (AA) by unscrewing the

preassembled hex nut and lock washer and then screwing the

mounting screws in or out of the crossbar until the correct length is

achieved. Once the Ceiling Canopy (A) is secure, remove the

mounting ball and Ceiling Canopy (A) and proceed to Step 5A.

Assembly Instruction

Summary of content (3 pages)

PAGE 1
Assembly Instruction . . , Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (4) Candelabra Base 60W Maximum. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
(Step 1B Continued) G AA A then attach Nipple (F) and the Ceiling Canopy (A) to the Swivel using The Flat Washer (G) and the Hex Nut (E) as in step A. Hex Nut and Lock Washer Mounting Screw E A F Optional Swivel Supply Wires and Ground Wire Mounting Ball Figure 4A B STEP 5A - Wire Connections H A. Use standard wire connectors (not included) to make all wire connections. (Connectors are not included with fixture.) Twist connectors until wires are tightly joined together.
PAGE 3
(Step 5B Continued) AA using the previously removed mounting balls. Hand tighten until snug. Mounting Screw FINISH: POLISHED NICKEL A Mounting Ball PENDANT LIGHT 6”Dia. 4.75” Dia. Figure 5B 0.5” 1 45.75” OVERALL HEIGHT (2) 6” AND (2) 12” RODS INCLUDED STEP 6B - Install Bulbs Bulb 2 A. This fixture uses candelabra bulb with standard screw base. Maximum 60 watts. Insert bulb and screw snugly into place. Your fixture is now assembled and ready to use. Enjoy! Figure 6B Socket 12.