File:01rcpic.
File:01rcpic.
File:01rcpic.ex Update:Mon Jun 3 09:22:39 1996 *[PI00425( ALL)05/95] Table of Contents Introduction .................................................... 1 Instrumentation .............................................. 7 Electronic Sound Systems ......................... 25 Controls and Features ................................ 59 Seating and Safety Restraints ................ 103 Starting ......................................................... 145 Driving .................................................
File:02rciic.ex Update:Thu May 30 10:22:07 1996 Introduction *[II00200( ALL)01/96] *[II00300( ALL)01/96] Ford’s Commitment to You At Ford Motor Company, excellence is the continuous commitment to achieve the best result possible. It is dedication to learning what you want, determination to develop the right concept, and execution of that concept with care, precision, and attention to detail. In short, excellence means being the standard by which others are judged.
File:02rciic.ex Update:Thu May 30 10:22:07 1996 *[II01000( ALL)01/96] ❑ Integrity is never compromised. Our conduct *[II01100( ALL)03/96] Things to Know About Using This Guide *[II01200( ALL)03/96] Congratulations on the purchase of your new vehicle. This guide has information about the equipment and the options for your new vehicle. You may not have bought all of the options available to you. If you do not know which information applies to your vehicle, talk to your dealer.
File:02rciic.ex Update:Thu May 30 10:22:07 1996 *[II01800( ALL)01/96] *[II01900( ALL)12/95] Finding Information in This Guide *[II02000( ALL)03/96] The Quick Index at the end of the book provides a page number following each item which indicates where detailed information can be found. *[II02100( ALL)01/96] To use the Index, turn to the back of the book and search in the alphabetical listing for the word that best describes the information you need.
File:02rciic.ex Update:Thu May 30 10:22:07 1996 % Your Maintenance Schedule and Record Booklet *[II02500( ALL)03/96] The Maintenance Schedule booklet lists the services that are most important for keeping your vehicle in good condition. A record log is also provided to help you keep track of all services performed.
File:02rciic.ex Update:Thu May 30 10:22:07 1996 *[II03090( ALL)05/96] Ford ESP is an optional service contract, backed and administered by Ford. It provides: *[II03120( ALL)05/96] ❑ protection against repair costs after your [II03150( ALL)05/96] and *[II03180( ALL)05/96] ❑ other benefits during the warranty period *[II03210( ALL)05/96] You may purchase Ford ESP from any participating Ford Motor Company dealer. There are several Ford ESP plans available in various time-and-mileage combinations.
File:02rciic.ex Update:Thu May 30 10:22:07 1996 % *[II03400( ALL)01/96] *[II03500( ALL)01/96] *[II03600( ALL)01/96] % Breaking Your Vehicle In Your new vehicle goes through an adjustment or break-in period during the first 1,000 miles (1,600 km) that you drive it. During the break-in period, you need to pay careful attention to how you drive your vehicle. ❑ Avoid sudden stops.
File:03rcisc.
File:03rcisc.ex Update:Fri Jun 7 13:56:06 1996 % The instrument panel (dashboard) on your vehicle is divided into several different sections. The illustrations on the following pages show the major parts of the instrument panel that are described in this chapter. Some items shown may not be on all vehicles. *[IS00800( BC )04/96] In your vehicle, the warning lights and gauges are grouped together on the instrument panel. We call this grouping a cluster.
File:03rcisc.
File:03rcisc.ex Update:Fri Jun 7 13:56:06 1996 % *[IS01700( BCGV)01/96] *[IS02000( BCGV)01/96] *[IS02600( ALL)01/96] *[IS02700( ALL)03/96] % The Mechanical Cluster The following warning lights and gauges are on the mechanical cluster. All of the warning lights and gauges alert you to possible problems with your vehicle. Some of the lights listed are optional. The following sections detail what each of these indicators means.
File:03rcisc.ex Update:Fri Jun 7 13:56:06 1996 % [IS03300( ALL)04/96] Anti-Lock Brake System Light (If equipped) [IS03400( ALL)12/95] This warning light will go on each time you start your vehicle. If it remains on for longer than five seconds, you should shut off your engine and restart. If the anti-lock brake light stays on, this indicates that the anti-lock feature is disabled and should receive immediate attention by a qualified service technician.
File:03rcisc.ex Update:Fri Jun 7 13:56:06 1996 *[IS03700( ALL)03/96] RWARNING If the anti-lock brake system warning light remains on or comes on while driving, have the braking system checked by a qualified service technician as soon as possible. *[IS03800( ALL)03/96] NOTE: If a fault occurs in the anti-lock system, and the brake warning light is not lit, the anti-lock system is disabled but normal brake function remains operational.
File:03rcisc.ex Update:Fri Jun 7 13:56:06 1996 *[IS06300( ALL)03/96] *[IS06400( ALL)04/96] Air Bag Readiness Light *[IS06500( ALL)04/96] If the light fails to illuminate, continues to flash, remains on, or you hear a beeping sound, have the system serviced at your Ford or Lincoln-Mercury dealer immediately. % The air bag system uses a readiness light and a tone to indicate the condition of the system. The readiness light is in the instrument cluster.
File:03rcisc.ex Update:Fri Jun 7 13:56:06 1996 [IS07350( BC )03/96] one inch art:0011209-A The low coolant light *[IS07500( ALL)01/96] *[IS07600( ALL)01/96] % Charging System Light This light indicates that your battery is not being charged and that you need to have the electrical system checked. [IS07700( ALL)04/96] one inch art:0010119-B The charging system light *[IS07800( ALL)03/96] This light illuminates every time you turn the ignition to the ON or START position (engine off).
File:03rcisc.ex Update:Fri Jun 7 13:56:06 1996 *[IS08700( ALL)04/96] This light tells you that the Transmission Control Switch (TCS) has been pushed. When the light is on, the transmission will not shift into overdrive. Depressing the button will return the vehicle to “overdrive on” mode. The transmission will be in the “overdrive on” mode when the vehicle is started even if the O/D OFF mode was selected when the vehicle was last shut off.
File:03rcisc.ex Update:Fri Jun 7 13:56:06 1996 *[IS09000( ALL)03/96] *[IS09100( ALL)03/96] % High Beam Light This light illuminates when the headlamps are turned to high beam or when you flash the lights. [IS09200( ALL)04/96] one inch art:0010125-B The high beam light *[IS11050( BC )12/95] % [IS11100( ALL)05/96] * % Service Engine Soon Warning Light This light illuminates when the engine’s Emission Control System requires service.
File:03rcisc.ex Update:Fri Jun 7 13:56:06 1996 [IS12200(MBC )04/96] This light is used when you set the anti-theft alarm system. See Anti-Theft System in the Controls and Features chapter for more information. *[IS12300( ALL)03/96] *[IS12400( ALL)03/96] Turn Signal Indicator Lights % The turn signal arrow will flash to indicate the direction in which you are going to be turning.
File:03rcisc.ex Update:Fri Jun 7 13:56:06 1996 % [IS13001( BC )03/96] Door Ajar Light (If equipped) [IS13101( BC )03/96] This light tells you when any door is not completely shut. It glows when the key is in the ON position. [IS13201( BC )03/96] one inch art:0010126-C The door ajar light % Engine Oil Pressure Light [IS13300( BC )05/96] This light indicates the engine oil pressure, not the oil level. However, if your engine’s oil level is low, it could affect the oil pressure.
File:03rcisc.ex Update:Fri Jun 7 13:56:06 1996 [IS13550( BC )04/96] 3. Check the engine’s oil level, following the instructions on checking and adding engine oil, see Engine Oil in the Index. If you do not follow these instructions, you or others could be injured. To assure an accurate reading, your vehicle should be on level ground. [IS13600( BC )03/96] 4. If the level is low, add only as much oil as necessary before you start the engine again. Do not overfill.
File:03rcisc.ex Update:Fri Jun 7 13:56:06 1996 % [IS13900( BC )04/96] Washer Fluid Low Light *[IS13950( BC )04/96] This light comes on if the reservoir is less than a quarter full when you turn on the windshield washers.
File:03rcisc.ex Update:Fri Jun 7 13:56:06 1996 *[IS14800( ALL)01/96] With ignition switch OFF, the fuel gauge indicator may drift from the ignition switch ON position. *[IS15700( ALL)03/96] *[IS15800( ALL)02/96] Engine Coolant Temperature Gauge [IS15905( BCGV)04/96] The pointer moves from the C (cold) mark into the normal band as your engine coolant warms up. Under normal driving conditions, the pointer should stay in the normal band.
File:03rcisc.ex Update:Fri Jun 7 13:56:06 1996 *[IS16400( ALL)03/96] *[IS16500( ALL)04/96] *[IS16600( ALL)01/96] *[IS16700( ALL)03/96] If your engine overheats: 1. Pull off the road as soon as safely possible. 2. Turn off the engine. 3. Let the engine cool. DO NOT REMOVE COOLANT SYSTEM FILL CAP UNTIL THE ENGINE IS COOL. *[IS16800( ALL)03/96] 4. Check the coolant level following the instructions on checking and adding coolant to your engine, see Engine Coolant in the Index.
File:03rcisc.ex Update:Fri Jun 7 13:56:06 1996 *[IS20400( ALL)01/96] *[IS20500( ALL)04/96] Trip Odometer [IS20600( ALL)04/96] Since the trip odometer displays distance independent of the odometer it will not always advance to the next mile (kilometer) at the same time as the odometer. % *[IS20700(MBC )03/96] % If you want to track your mileage up to 999.9 miles (kilometers), use the trip odometer.
File:04rcasc.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 % *[AS01105( BC )10/95] *[AS01175( BC )10/95] Compact Disc Radio The Compact Disc Radio combines the Electronic Stereo Radio with the Ford Compact Disc Player. [AS01200( BC )10/95] Using the Controls on Your New Compact Disc Radio *[AS01300( BC )10/95] Most of the features of this unit work for both radio and CD operation.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS02100( BC )03/96] *[AS02200( BC )10/95] How to tune radio stations *[AS02300( BC )10/95] ❑ Using the “SCAN/TUNE” button to manually % There are four ways for you to tune in a particular station. You can manually locate the station using the “SCAN/TUNE” button, “SEEK” the station, “SCAN” to the station or select the station by using the memory buttons, which you can set to any desired frequency. These four methods are described below.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS02600( BC )04/96] *[AS02700( BC )04/96] ❑ Using the “SEEK” function *[AS02800( BC )02/96] ❑ Using the “SCAN/TUNE” button to scan This feature on your radio allows you to automatically select listenable stations up or down the frequency band. Press the top a half of the “SEEK” button to select the next listenable station up the frequency band. Press the bottom b half of the button to select the next listenable station down the frequency band.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS03350( BC )08/95] Follow the easy steps below to set these buttons to the desired frequencies: *[AS03400( BC )03/96] *[AS03600( BC )10/95] 1. Select a band, then select a frequency. 2. Press one of the memory preset buttons and hold the button until the sound returns. That station is now held in memory on that button. *[AS03700( BC )10/95] 3. Follow the two steps above for each station memory preset button you want to set.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 momentarily on the stations being set into the memory buttons. The radio is now in the “AUTO” mode and the display will show “AUTO” each time a preset is activated. *[AS04350( BC )10/95] NOTE: If there are fewer than five strong stations in the frequency band, the remaining unfilled buttons will store the last strong station detected on the band.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS04950( BC )02/96] [AS05000( BC )10/95] *[AS05100( BC )04/96] [AS05200( BC )10/95] *[AS05300( BC )10/95] ❑ Adjusting speaker balance Balance control allows you to adjust the sound distribution between the right and left speakers. Push the “AUDIO” button repeatedly until the display reads “BAL”. Push the top (+) side of the “VOLUME” button to shift the sound to the right speakers, and push the bottom (-) side to shift the sound to the left speakers.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS07100( BC )09/95] NOTE: If after you insert a disc, the disc is ejected and “ERROR” begins scrolling in the display, remove the disc and reinsert it right side up (label side up). [AS07200( BC )10/95] The digital display on your CD player will either show the track (selection) number or the elapsed time. (The display mode can be selected by pressing the memory preset button #6.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 [AS07650( BC )04/96] NOTE: Once a disc is inserted, the disc opening is secured to prevent the accidental insertion of a second disc. *[AS07700( BC )10/95] NOTE: The CD player has heat protection circuitry to protect the laser diode. If the temperature of the player reaches 167˚F (75˚C), the heat detection circuit will shut off the player and “TOO HOT” will scroll in the display for approximately five seconds (radio will resume playing).
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 desired point (found by watching the elapsed playing time in the display or by listening to the sound during fast forward or reverse). When you have reached the beginning of track 1, the CD player will begin playing. *[AS08000( BC )10/95] When you have reached the end of the disc by keeping the fast forward button pressed, the display will show “END” and the player will go into pause mode.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS08080( BC )10/95] *[AS08090( BC )10/95] ❑ Automatic Disc Storage *[AS08095( BC )04/96] *[AS08096( BC )10/95] How to eject the disc *[AS08097( BC )10/95] NOTE: You can eject the disc while the radio power and/or ignition is on or off.
File:04rcasc.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 % [AS21370(MBC )06/95] Electronic Stereo Cassette Radio *[AS21400(MBC )03/96] *[AS21500(MBC )08/95] Using the Controls on Your New Radio *[AS22050(MBC )10/95] Press the “POWER” button to turn the radio on. Press it again to turn it off. *[AS22060(MBC )02/96] Press the right (+) side of the “VOLUME” button to increase the volume. Press the left (S) side of the button to decrease the volume. Illuminated bars in the display show the relative volume level.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 [AS22450(MBC )05/95] ❑ Using the “AMS” function to manually tune your radio [AS22650(MBC )03/95] You can change the frequency up or down one increment at a time by first pressing the “AMS” button, (display shows “TUNE”) then pressing and releasing either the right a or left b side of the “SEEK” button. To change frequencies quickly, press and hold down either the right or left side of the “SEEK” button.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS23200(MBC )02/96] *[AS23300(MBC )10/95] ❑ Setting the Station Memory Preset buttons *[AS23400(MBC )08/95] Follow the easy steps below to set these buttons to the desired frequencies: *[AS23500(MBC )03/96] *[AS23700(MBC )10/95] 1. Select a band, then select a frequency. 2. Press one of the memory preset buttons and hold the button until the sound returns. That station is now held in memory on that button. *[AS23800(MBC )10/95] 3.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS24500(MBC )02/96] *[AS24600(MBC )02/96] *[AS24750(MBC )02/96] Speaker features and operation *[AS24800(MBC )04/96] *[AS24950(MBC )02/96] ❑ Adjusting speaker fader *[AS24960(MBC )10/95] NOTE: Illuminated bars in the display show relative levels of bass and treble, and positions of speaker balance and fader functions (left to right, front to rear).
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS25700(MBC )12/95] *[AS25800(MBC )06/95] How to locate a desired track on the tape [AS25810( BC )09/95] NOTE: Depending on your vehicle, the display of your radio may show arrows (g or h) or numerals (“1” or “2”) to indicate the direction of tape travel. In either case, at the end of the tape, the direction automatically reverses and plays the other side of the tape.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 [AS26300( BC )07/92] ❑ Using the Automatic Music Search (“AMS”) (if your display shows arrows) Press and hold the “AMS” button. Then, push the appropriate fast-wind button, depending upon the direction of the tape travel arrow in the display. For example, if the tape travel arrow is pointing to the left, push the left h button to rewind to the beginning of the current selection.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS26900(MBC )08/95] *[AS27000(MBC )02/96] ❑ How to change the side of the tape being played The alternate track (other side) of the tape can be selected at any time by pushing both fast-wind buttons h and g at the same time. *[AS27100(MBC )08/95] *[AS27250(MBC )04/96] How to eject the tape *[AS27300(MBC )02/96] *[AS27400(MBC )09/95] Using the DolbyH B noise reduction feature *[AS27500(MBC )04/96] Push the k button to activate.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS27900(MBC )08/95] ❑ Protect cassettes from exposure to direct *[AS28001(MBC )08/95] ❑ If a tape is loose inside the cassette, tighten it *[AS28101(MBC )08/95] ❑ Loose labels on cassette tapes can become *[AS28200(MBC )08/95] ❑ Do not leave a tape in the cassette tape sunlight, high humidity and extreme heat or cold. If they are exposed to extreme conditions, allow them to reach a moderate temperature before playing.
File:04rcasc.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 % *[AS43458( BC )08/95] *[AS43460(MBC )03/96] *[AS43470(MBC )03/96] *[AS43480(MBC )10/95] High-Level Audio System Using the Controls on Your New Radio How to turn the radio on and off Press the “POWER” button to turn the radio on. Press it again to turn it off. *[AS43500(MBC )03/96] How to adjust the volume [AS43510(MBC )06/95] Press the R/S side of the “VOLUME” button to increase/decrease volume.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS43550(MBC )03/96] *[AS43560(MBC )10/95] How to tune radio stations *[AS43570(MBC )03/96] *[AS43580(MBC )03/96] ❑ Using the “TUNE” function % *[AS43590(MBC )03/96] *[AS43600(MBC )04/96] *[AS43610(MBC )09/95] There are four ways for you to tune in a particular station.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS43630(MBC )04/96] *[AS43640(MBC )03/96] ❑ Using the “SCAN” function Pressing the “SCAN/TUNE” button once enters the scan mode (display will indicate “SCN”). Pushing the right a side of the “SEEK” button will begin the scan mode up the frequency band, stopping on each listenable station for approximately a five-second sampling.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS43750(MBC )10/95] *[AS43760(MBC )10/95] ❑ Using the Automatic Memory Load feature *[AS43770(MBC )05/96] With Auto Memory Store, you can continually set strong stations into your memory buttons without losing your existing memory presets, which is especially helpful while traveling. Your radio will automatically set your memory buttons to the strong local stations so you don’t have to continually manually tune to existing stations.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS43810(MBC )02/96] To deactivate the Auto Memory Store mode and return to the manually-set memory button stations (or those stations set using Auto Memory Load), simply push the “AUTO PRESET” button. Display will show “AUTO” then “OFF.” The next time Auto Memory Store is activated on that band, the radio will store the next set of five strong stations.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS44010(MBC )04/96] *[AS44020(MBC )02/96] ❑ Adjusting speaker fader *[AS44030(MBC )10/95] NOTE: Illuminated bars in the display show relative levels of bass and treble, and positions of speaker balance and fader functions (left to right, front to rear). Fade control allows you to adjust the sound distribution between the front and rear speakers. Push the “AUDIO” button repeatedly until the display reads “FADE.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS44100(MBC )12/95] *[AS44110(MBC )08/95] How to locate a desired track on the tape *[AS44120(MBC )09/95] ❑ Fast forwarding the tape There are four ways to quickly locate a desired selection on the tape. You can use the fast forward, rewind, “SEEK” or “SCAN” function. Following are brief descriptions of each. [AS44140(MBC )02/95] To fast forward the tape, press the “FF” button.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS44230(MBC )08/95] ❑ Using the “SCAN” function with your cassette tape player *[AS44240(MBC )03/96] Press the “SCAN/TUNE” button to enter the scan mode (display indicates “SCN”). Pushing the right a side of the “SEEK” button will begin the forward scan mode on the tape currently playing, stopping on each tape selection for approximately an eight-second sampling.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS44320(MBC )08/95] *[AS44330(MBC )08/95] How to store the tape Press the “AM/FM” button to stop the tape player and resume radio play. The cassette will be stored in the tape player and the X symbol in the display will be lit until you push the “PLAY PROG” button to resume tape play. Fast forward and fast rewind can be used while the tape is in storage mode without interrupting radio play.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS44530(MBC )08/95] Error 2 — Tape eject or load failure. Your cassette tape player will go into the pause mode. Push “EJCT” to eject the tape. If the tape doesn’t eject, refer the problem to qualified personnel for service.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS60900( ALL)04/96] Common Radio Reception Conditions *[AS61000( ALL)08/95] Several conditions prevent FM reception from being completely clear and noise-free, such as the following: *[AS61100( ALL)08/95] *[AS61200( ALL)08/95] 1. *[AS61300( ALL)04/96] NOTE: Always make sure your antenna is fully extended to the maximum length for proper reception.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS61900( ALL)08/95] To minimize these conditions, a stereo/mono blend circuit has been incorporated into this system. This feature automatically switches a weak stereo signal to a clearer monaural signal, which improves the quality of reception. *[AS62000( ALL)08/95] Several sources of static are normal conditions on AM frequencies. These can be caused by power lines, electric fences, traffic lights and thunderstorms.
File:04rcasc.ex Update:Thu May 30 10:24:18 1996 *[AS62600( ALL)08/95] Not all frequencies will be assigned to a given area. This radio will tune to each of these frequencies using manual tune and no fine tuning is necessary as radio stations may not use other frequencies. *[AS62700( ALL)08/95] Some FM radio stations advertise a “rounded-off” frequency which is not the frequency they actually broadcast on. For example, a radio station that is assigned a frequency of 98.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 Controls and Features *[CF00200( ALL)01/96] The main controls for the climate control system, clock, and radio are on the instrument panel. *[CF00300( ALL)03/96] NOTE: Any cleaner or polish that increases the gloss (shine) of the upper part of the instrument panel should be avoided. The dull finish in this area is to help protect the driver from undesirable windshield reflection.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 [CF04100( BC )05/96] one third page art:0011216-C The controls for the manual heating and air conditioning system [CF04300( BC )04/96] To heat the interior of your vehicle, turn the SELECT control to FLOOR, turn the TEMP control to the end of the red range (full right) and turn the FAN control to HI. Temperature and fan speed can be adjusted as desired.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 [CF05100( BC )04/96] To cool your vehicle using outside air, turn the SELECT control to A/C, turn the TEMP control all the way to the end of the blue range (full left) and turn the FAN control to the desired speed between LO and HI. A/C provides quieter system operation than MAX A/C, but it is not as efficient as MAX A/C which uses recirculated air.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 % [CF06100( BCGV)12/95] Adjusting the panel register airflow [CF06200( BCGV)04/96] The instrument panel registers may be adjusted to your comfort needs. The thumbwheel controls the volume of air and the control in the center of the register controls direction up or down or side to side.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 [CF06700( BC )05/96] one third page art:0010662-E The controls for the Semi-Automatic Temperature Control system [CF06800( BC )12/95] System Controls [CF06850( BC )04/96] This display also has a metric conversion option. To change from English to Metric, set the control to MAX A/C and the Fan to HI. Simultaneously press the WARM, COOL, and OUTSIDE TEMP controls for 3/4 of a second, then release.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 [CF07300( BC )05/96] If the control is pressed after 65˚F (18˚C) is reached, only 60˚F (16˚C) will be displayed and the system will provide continuous maximum cooling. [CF07400( BC )05/96] Warm control [CF07500( BC )05/96] This control is used to RAISE the temperature setting. Press the control once to raise the displayed temperature one degree.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 [CF08100( BC )05/96] To cool your vehicle quickly in warm weather, turn the SELECT control to MAX A/C and turn the FAN control to AUTO. As the vehicle interior cools down, the discharge air temperature and fan speed will automatically and gradually be changed to maintain the set temperature with airflow from the instrument panel registers.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 % Rear Window Defroster (If equipped) *[CF14600( ALL)03/96] The defroster for the rear window clears frost, fog, or thin ice from both the inside and outside of the rear window. [CF14900( BC )05/96] The control for the rear window defroster is located on the lower right side of the instrument panel, just left of the climate control panel.
File:05rccfc.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 *[CF16800( ALL)03/96] *[CF17100( BCGV)05/96] % Turning On the Exterior Lights To turn on the headlamps, parking lamps, side markers, license plate lamps and tail lamps, use the rotary control that is to the left of the steering wheel.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 [CF17700( BCGV)12/95] Chime for headlamps on *[CF17800( ALL)12/95] This chime sounds if the driver or any passenger door is open when the parking lamps or headlamps are on. The chime sounds until you close the door, turn off the lamps or turn the ignition to the ON position. % Setting the Autolamp Delay System (If equipped) *[CF18100( BCGV)05/96] The autolamp sets the headlamps to turn on and off automatically.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 *[CF18700( BC )05/96] *[CF18900( BC )05/96] To set the autolamp: 1. Make sure the headlamp control is in the OFF position. If the control for the headlamps is ON, you cancel the autolamp. *[CF19000( BC )05/96] 2. Turn the ignition key to ON or start your vehicle. [CF19100( BC )12/95] 3. Find the autolamp thumbwheel to the right of the panel dim thumbwheel. [CF19200( BC )12/95] 4.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 % Lighting Up the Interior and Instrument Panel [CF20100( BC )12/95] Manual operation *[CF20200( BC )05/96] With the light control in the parking lamps or the headlamps position, you can brighten or dim the lights in the instrument panel. To do this, use the thumbwheel to the left of the steering wheel. This wheel also turns on the interior lights with the light control on or off.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 % *[CF20800( ALL)03/96] Clock [CF21100( BC )12/95] quarter page art:0011164-B The digital clock [CF21200( ALL)12/95] 1. To set the hour, press and hold the H button. When the desired hour appears, release the button. [CF21300( ALL)12/95] 2. To set the minutes, press and hold the M button. When the desired minute appears, release the button.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 *[CF24100( ALL)01/96] % [CF24200( ALL)01/96] * Ignition Understanding the Positions of the Ignition [CF24300( ALL)12/95] quarter page art:0010035-B The positions of the key in the ignition *[CF24500( BCGV)04/96] ACC allows some of your vehicle’s electrical accessories such as the radio and the windshield wipers to operate while the engine is not running. % [CF24600( ALL)12/95] LOCK locks the steering wheel.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 *[CF25100( ALL)03/96] *[CF25200( BCGV)03/96] *[CF25400( ALL)01/96] *[CF25500( BCGV)03/96] *[CF25700( BCGV)03/96] Removing the Key From the Ignition [CF26300( BCGV)12/95] NOTE: The automatic transmission gearshift must be in P (Park) to move the key to the lock position. % 1. Put the gearshift in P (Park). 2. Set the parking brake fully. 3. Turn the ignition key to LOCK. 4. Remove the key.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 [CF27600( ALL)12/95] one third page art:0011292-A The turn signal lever *[CF27700( ALL)01/96] *[CF27800( ALL)01/96] Turn Signals *[CF27900( ALL)01/96] If the turn signal stays on after you turn, move the lever back to the center (off) position. *[CF28000( ALL)01/96] For lane changes, move the lever far enough to signal but not to latch. The lever will return to the off position when you release it.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 *[CF28700( ALL)01/96] *[CF28800( ALL)01/96] Flashing the Lights *[CF28900( ALL)01/96] *[CF29000( ALL)04/96] Windshield Wipers and Washer % % To flash the headlamps, pull the lever toward you for a moment and then release it. The headlamps will flash whether the headlamp knob is in the on or off position. To turn on the windshield wipers, the ignition key must be turned to the ON or ACC position.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 [CF29600( ALL)04/96] To set the interval wipers, turn the knob at the end of the turn signal lever toward or away from you until the wipers are going at the desired interval. *[CF29700( ALL)01/96] *[CF29800( ALL)12/95] Windshield Washer *[CF29900( ALL)03/96] If the washer does not work, check the washer fluid level and fill it if it is low. See the Maintenance and Care chapter. If there is enough fluid, consult your nearest Ford or Lincoln-Mercury dealer.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 % *[CF30300( ALL)03/96] *[CF30400( ALL)05/96] Hazard Flasher The hazard flasher serves as a warning to other drivers to be careful when approaching or passing your vehicle.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 % *[CF30700( ALL)05/96] *[CF30800( ALL)01/96] Horn To sound the horn, push the center pad area of the steering wheel.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 % *[CF31200( ALL)01/96] *[CF31300( ALL)02/96] Tilt Steering RWARNING Never adjust the steering wheel when the vehicle is moving. [CF31400(MBC )12/95] half page art:0010088-B The lever to tilt the steering wheel *[CF31600( ALL)01/96] To change the position of the steering wheel, pull the release lever on the column toward you. Tip the steering wheel to the desired position. Release the lever to lock the steering wheel in place.
File:05rccfc.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 *[CF32700( ALL)05/96] Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill. If your vehicle speed is faster than the set speed while driving on a downhill in j (Overdrive), you may want to shift to the next lower gear to reduce your vehicle’s speed. [CF32800( ALL)05/96] If your vehicle slows down more than 10 mph (16 km/h) below your set speed on an uphill, your speed control will disengage. This is normal.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 *[CF33500( ALL)05/96] *[CF33600( ALL)05/96] To Set a Lower Set Speed *[CF33700( ALL)05/96] ❑ Press and release COAST. Each press will *[CF33800( ALL)05/96] ❑ Depress the brake pedal. When the desired *[CF33900( ALL)05/96] *[CF34000( BCGV)05/96] *[CF34100( ALL)05/96] To Disengage Speed Control *[CF34200( ALL)05/96] To Return to a Set Speed [CF34300( ALL)04/96] ❑ Press and hold COAST. Release the switch when the desired vehicle speed is reached.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 [CF35900( BC )12/95] one third page art:0011214-A Map lamp (with optional moon roof) [CF36000( BC )12/95] one third page art:0010651-C Front seat map and dome lamps (without optional moon roof) *[CF36200( ALL)12/95] The dual beam map lamps are located on each side of the dome lamp. Each map lamp can be turned on by the switches on the lamp.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 % Moon Roof (If equipped) [CF37100( BC )05/96] You can move the moon roof back to open the glass panel, or you can tilt it up to ventilate the vehicle. [CF37200( BC )05/96] The rocker type control is used to open and close the moon roof. You must press and hold the control until the desired position is reached. At fully open and closed positions, the motor will automatically turn off. Release the control at this time to avoid motor damage.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 [CF37395( BC )05/96] The moon roof has an express open feature. [CF37400( BC )05/96] To open the moon roof, press and release the rear portion of the control. The glass panel will move to the full open position and stop. To stop the glass at a partially open position, press the control again while the glass is moving. *[CF37500( BC )05/96] To close the moon roof, press and hold the front portion of the control.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 *[CF38000( BC )01/96] RWARNING Do not let children play with the moon roof. They may seriously hurt themselves. *[CF38100( BC )01/96] *[CF38200( BC )01/96] Sliding Shade *[CF38300( BC )01/96] To close the sliding shade, pull the shade toward the front of the vehicle. The shade automatically opens and locks when the moon roof is opened. The moon roof has a sliding shade that you can manually open or close to block the sun when the glass panel is shut.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 *[CF39100( CGV)05/96] % Automatic Dimming Inside Rearview Mirror (If equipped) [CF39200( CGV)05/96] quarter page art:0010037-C The automatic non-glare mirror *[CF39300( CGV)05/96] The electronic day/night mirror will change from the normal state to the non-glare state when bright lights (glare) reach the mirror. This mirror functions at night, and has a limited function at dusk or dawn.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 [CF39600( CGV)12/95] There are two light sensors (photocells) in this mirror. The sensor that detects rear glare is located inside a widow in the center of the mirror. The second light sensor which determines outside light level is located on the backside of the mirror case. *[CF39605( CGV)05/96] NOTE: Do not block the sensor on the backside of the mirror (i.e., with a parking tag, car deodorizer, etc.) since this may impair proper mirror performance.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 % *[CF40800( ALL)02/96] % [CF41800( ALL)01/96] * Doors Power Door Locks (If equipped) [CF41900( ALL)12/95] If your vehicle has power door locks, the controls to lock the doors are on the trim panel of the front door. When you close the doors after you set the door locks, the doors remain locked. If the power mechanism fails, the manual door locks will override the power controls.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 % Using the Illuminated Entry System (If equipped) [CF42600( BC )05/96] The interior lights turn on when you lift the outside door handle on the driver’s side door or when you press UNLOCK, TRUNK, or PANIC on a programmed remote entry transmitter if your vehicle is equipped with remote entry. [CF42700( BCGV)05/96] These lights automatically turn off after 25 seconds or when you turn the ignition key to ON or ACC.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 % *[CF43405( ALL)04/96] % [CF43415( BCGV)12/95] * Windows Using the Power Windows [CF43420(MBC )12/95] Each door has a power control that opens and closes the window on that door. The driver’s door has a master control panel that operates the windows. *[CF43430( ALL)12/95] Power windows can only be opened or closed when the ignition switch is in the ON or ACC position. *[CF43435( ALL)01/96] RWARNING Do not let children play with the power windows.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 % [CF43600( BCGV)03/96] Adjusting the Dual Electric Remote Control Mirrors [CF43800(MBC )05/96] The switch for controlling the dual electric remote control mirrors is located on the driver’s door. Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 [CF44900( ALL)12/95] The Right Side Convex Mirror *[CF45000( ALL)12/95] The side view mirror on the right is a convex mirror. This mirror gives you a wider view of the lanes on your right and behind you. *[CF45100( ALL)05/96] RWARNING The right side view mirror makes objects appear smaller and farther away than they actually are. % Console [CF46200(MBC )12/95] Your vehicle has a full console.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 % [CF51000( ALL)12/95] Positive Location Floor Mat [CF51100(MBC )12/95] When installing or removing the driver’s side floor mat you must attach/detach the positive location grommet from the hook on the floor. The hook is just forward of the left hand track of the driver’s seat.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 % Anti-Theft Alarm System (If equipped) *[CF53300(MBC )01/96] When armed, this system helps protect your vehicle against break-ins or theft.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 % Arming the system [CF54500(MBC )12/95] To arm the system, do the following steps in sequence: *[CF54600(MBC )01/96] 1. [CF54700( BC )03/96] At this point, the anti-theft system automatically monitors the ignition keylock cylinder. If the lock cylinder is forcibly removed, the anti-theft alarm system will trigger. To arm the remaining portion of the system, follow steps 2-4. *[CF54800(MBC )05/96] 2. Open any door.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 [CF55300(MBC )12/95] You can also arm the anti-theft system by following this sequence: [CF55400(MBC )12/95] 1. Remove key from ignition. *[CF55500(MBC )01/96] 2. Close all of the doors. [CF55600(MBC )05/96] 3. Press the remote entry transmitter LOCK control. The alarm indicator will come on for 30 seconds to show the alarm is arming and then turn off to show that the alarm has armed.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 *[CF57200(MBC )03/96] *[CF57300(MBC )01/96] *[CF57400(MBC )12/95] *[CF57500(MBC )04/96] Disarming a Triggered System *[CF57600(MBC )01/96] NOTE: The flashing lights and honking horn will shut off automatically within 2 minutes 45 seconds after the system is triggered. It will trigger again if another intrusion occurs. However, the starter circuit remains disabled until the system is disarmed.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 [CF65500(MBC )05/96] one third page art:0001000-A Remote % Unlocking the doors and opening the trunk *[CF65800( ALL)04/96] To unlock the driver’s door, press the UNLOCK control. *[CF65900( ALL)04/96] To unlock the other doors, press the UNLOCK control a second time within five seconds of unlocking the driver’s door. *[CF66000( ALL)05/96] *[CF66200( ALL)04/96] *[CF66300( ALL)04/96] *[CF66400(MBC )05/96] To open the trunk, press the TRUNK control.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 [CF67400( ALL)05/96] When you use the remote entry UNLOCK, TRUNK or PANIC controls, the illuminated entry system turns on the interior lights for 25 seconds. You can turn these lights off with the LOCK control or by turning the ignition to the RUN position. The interior lights will not turn off if you have turned them on manually or if a door is open.
File:05rccfc.ex Update:Fri Jun 7 13:58:04 1996 *[CF68900(MBC )05/96] The remote can be snapped apart to replace the batteries by twisting a thin coin between the two halves of the remote. DO NOT TAKE THE FRONT PART OF THE REMOTE APART. When installing the new batteries, be sure to place the positive (+) side down as marked. Snap the two halves back together.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 Seating and Safety Restraints % *[SS00200( ALL)05/96] % [SS00300( ALL)05/96] * *[SS00400( ALL)01/96] Seats Head Restraints If you use them properly, head restraints will help protect your head and neck in a collision. *[SS00500( ALL)01/96] A head restraint helps protect you best if you position it behind your head and not behind your neck.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 % [SS01200(MBC )12/95] Adjusting Manual Seats *[SS01400( ALL)01/96] In the front seats, you can move the whole seat forward or backward or tilt the back of the seat forward or backward. [SS01500(MBC )12/95] To move the seats forward or backward: [SS01700( BCGV)12/95] 1. Find the adjustment bar underneath the front part of the seat. [SS01900( BCGV)12/95] 2. Lift the bar to unlatch the seat. *[SS02100( ALL)01/96] *[SS02200( BCGV)01/96] 3.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS03400( ALL)05/96] RWARNING Never adjust the driver’s seat or seatback when the vehicle is moving. *[SS03500( ALL)02/96] RWARNING Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS04300(MBC )02/96] RWARNING Check to see that the seat and seatback are latched securely in position. Keep floor area free of objects that would prevent proper seat engagement. Never attempt to adjust the seat while the vehicle is in motion. % Using the Power Seats (If equipped) [SS04700( BC )12/95] If your vehicle has power seats, you can adjust them in several directions. The controls are on the side of the seats.
File:06rcssc.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS07500(MBC )12/95] % Rear Seat Entry [SS07700( BC )12/95] one third page art:0010264-A Entering the rear seat [SS07900(MBC )12/95] The rotating boot on the lap belt is designed to allow rear seat entry/exit. To enter the rear seat: *[SS08000( BC )12/95] *[SS08200( BC )12/95] *[SS08400( BC )12/95] 1. Rotate the safety belt boot rearward. 2. Enter the rear seat in front of the safety belt. 3.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS11400( ALL)02/96] To help you remember to fasten your safety belt, a warning light may come on and a chime may sound. See Safety Belt Warning Light and Chime in the Instrumentation chapter. *[SS11500( ALL)02/96] See the following sections in this chapter for directions on how to properly use these safety belts. Also see Safety Restraints for Children in this chapter for special instructions about using safety belts for children.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS11900( ALL)02/96] RWARNING Children should always ride with the seatback in the fully upright position. *[SS12000( ALL)02/96] RWARNING Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. *[SS12100( ALL)02/96] RWARNING Lock the doors of your vehicle before driving to lessen the risk of the door coming open in a collision.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS12700( BCGV)01/96] quarter page art:0010018-B Fastening the front seat combination lap and shoulder belt [SS13000( BCGV)12/95] one third page art:0010502-A Fastening the rear seat combination lap and shoulder belt *[SS13200( ALL)02/96] NOTE: Be sure to read and understand Important Safety Belt Information in this chapter.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS13900( ALL)02/96] Dual locking mode retractors operate in two ways: *[SS14000( ALL)02/96] Vehicle sensitive (emergency) locking mode [SS14100( ALL)12/95] In this operating mode, the shoulder belt retractor will allow the occupant freedom of movement, locking tight only on hard braking, hard cornering or impacts of approximately 5 mph (8 km/h) or more. The retractor can also be made to lock by pulling/jerking on the belt.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS14800( ALL)01/96] To switch the retractor from the emergency locking mode to the automatic locking mode, perform the following steps: *[SS14900( ALL)02/96] *[SS15000( ALL)01/96] 1. Buckle the lap/shoulder combination belt. 2. Grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and, when allowed to retract, a clicking sound is heard.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS17900( BC )05/96] Before you can reach and latch a combination lap and shoulder belt having a cinch tongue into the buckle, you may have to lengthen the lap belt portion of it. To lengthen the lap belt, pull some webbing out of the shoulder belt retractor. While holding the webbing below the tongue, grasp the tip (metal portion) of the tongue so that it is parallel to the webbing and slide the tongue upward.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS18200( BC )05/96] To fasten a cinch tongue, pull the combination lap and shoulder belt from the retractor so that the shoulder belt portion of the safety belt crosses your shoulder and chest. Be sure the belt is not twisted. If the belt is twisted remove the twist. Insert the belt tongue into the proper buckle for your seating position until you hear a snap and feel it latch.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS18700( BC )05/96] While you are fastened in the seat belt, the combination lap/shoulder belt with a cinch tongue adjusts to your movement. However, if you brake hard, turn hard, or if your vehicle receives an impact of 5 mph (8 km/h) or more, the safety belt will become locked and help reduce your forward movement. [SS18800( ALL)01/96] To unfasten all the belts: [SS18900(MBC )01/96] 1. Push the release button on the end of the buckle.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS19600( ALL)01/96] 2. While the belt retracts, guide the tongue to its stowed position. If you do not guide the tongue, it may strike you or part of the vehicle. % [SS20200( BC )12/95] Lap Belts — Rear Center Seating Positions *[SS20500( BC )12/95] The lap belt in the center of the rear seat does not adjust automatically. You must adjust it to fit snugly and as low as possible around your hips. Do not wear it around your waist.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 [SS21300( BC )12/95] one third page art:0000029-E Unfastening center rear seat lap belt *[SS21400( ALL)02/96] *[SS21500( ALL)01/96] % Safety Belt Extension Assembly For some people, the safety belt may be too short even when it is fully extended. You can add about eight inches (20 cm) to the belt length with a safety belt extension assembly (part number 611C22). Safety belt extensions are available at no cost from your dealer.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 % *[SS21800( ALL)03/96] *[SS21900( ALL)02/96] Safety Belt Maintenance Check the safety belt systems periodically to make sure that they work properly and are not damaged.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS22401( ALL)05/96] RWARNING All occupants of the vehicle, including the driver, should always wear their safety belts, failure to do so may increase the risk of personal injury in the event of a collision. *[SS22601( ALL)05/96] RWARNING Do not place objects or mount equipment on or near the air bag covers that may come into contact with an inflating air bag.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS22901( ALL)05/96] *[SS23001( ALL)05/96] *[SS23101( ALL)05/96] Children and Air Bags NOTE: For additional important safety information on the proper use of seat belts, child seats, and infant seats, please read the entire Safety Restraints chapter in this owner guide. RWARNING Children should always wear their safety belts. Failure to follow these instructions may increase the risk of personal injury in the event of a collision.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 or sodium compounds, such as sodium carbonates (e.g. baking soda) that result from the combustion process that inflates the air bag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic. The Air Bag Supplemental Restraint System will reduce, but not eliminate all injuries in an accident. *[SS23601( ALL)05/96] RWARNING Several air bag system components get hot after inflation.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 [SS24350( ALL)04/96] The diagnostic module monitors its own circuits, the air bag electrical system, the air bag readiness light, the air bag power, and the air bag inflators. *[SS24401( ALL)05/96] *[SS24501( ALL)05/96] Determining if System Is Operational The Air Bag Supplemental Restraint System uses a readiness light and a tone to indicate the condition of the system. The readiness light is in the instrument cluster.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS25101( ALL)05/96] Disposal of Air Bags and Air Bag Equipped Vehicles *[SS25201( ALL)05/96] For disposal of air bags or air bag equipped vehicles, see your local Ford or Lincoln-Mercury dealer. Air bags MUST BE disposed of by qualified personnel. *[SS26300( ALL)01/96] *[SS26400( ALL)01/96] Safety Restraints for Children % In the U.S. and Canada, you are required by law to use safety restraints for children.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS26800( ALL)03/96] RWARNING Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision. *[SS26900( ALL)01/96] RWARNING Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS27600( ALL)05/96] Children weighing less than 40 lbs. (18 kg) should use child or infant seats. Forward facing child seats must have the passenger seat moved as far back from the instrument panel as possible. *[SS27700( ALL)05/96] RWARNING Rear-facing child seats or infant carriers should never be placed in the front seats.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 % Installing Safety Seats in the Front Outboard Passenger Seating Position [SS30700( ALL)12/95] For seating positions equipped with a dual locking mode retractor, use the following procedure. [SS30800( ALL)04/96] If you choose to install a forward-facing child safety seat in the front seating positions, move vehicle seat as far back as possible. *[SS30900( ALL)05/96] 1. Position the child seat in the center of the passenger seating position.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS31200( ALL)01/96] 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. See Figure 2. Be sure that the belt webbing is not twisted.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS31400( ALL)01/96] 4. Insert the belt tongue into the buckle for that seating position until you hear and feel the latch engage. See Figure 3. Make sure tongue is latched securely to buckle by pulling on tongue.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS31600( ALL)01/96] 5. Grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. At this time, the retractor is in the automatic locking mode (child seat restraint mode). See Figure 4. *[SS31700( ALL)01/96] NOTE: The dual-locking mode retractor must be in the automatic locking mode to properly restrain a child.
File:06rcssc.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS32200( ALL)01/96] 7. Before placing the child in the child seat, forcibly tilt the seat from side to side, and tug it forward to make sure that the seat is securely held in place. See Figure 7.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS32400( ALL)01/96] 8. Double check that the retractor is in the automatic locking mode. Try to pull more belt out of the retractor. If you cannot, the belt is in the automatic locking mode. See Figure 8. *[SS32500( ALL)04/96] half page art:0011245-C Checking the retractor *[SS32600( ALL)01/96] 9. Check to make sure that the child seat is properly secured prior to each use. If the retractor is not locked, repeat steps 4 through 7.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 % Installing Child Safety Seats in the Rear Outboard Seating Positions *[SS32900( BC )05/96] Your rear outboard seating positions are equipped with a cinch tongue on the safety belts. Use the following procedure for installing a child safety seat in these locations. *[SS33000( BC )05/96] 1. *[SS32800( BC )05/96] Grasp the belt webbing below the tongue and pull as much of the belt out of the retractor as possible. Hold the belt out. See Figure 1.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS33300( BC )05/96] 2. With your other hand, grasp the tip (metal portion) of the tongue (not the cover) and slide the tongue up the webbing as far as it will go. See Figure 1. Release the tongue, but do not let go of the lap portion of the belt webbing. *[SS33400( BC )05/96] 3.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS33700( BC )05/96] 5. [SS33800( BC )04/96] half page art:0011365-A 136 Insert the belt tongue into the proper buckle for that seating position until you hear a snap and feel it latch. Make sure the tongue is securely latched to the buckle by pulling on the tongue. See Figure 3.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS33900( BC )05/96] 6. Push down on the child seat and pull up on the shoulder belt portion to tighten the lap belt portion of the combination lap and shoulder belt. See Figure 4.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS34100( BC )05/96] 7. [SS34200( BC )04/96] half page art:0011367-A 138 Grasp belt close to child seat and pull on the shoulder belt portion of the combination lap/shoulder belt, then allow the belt to retract and remove all slack to securely tighten the child safety seat in the vehicle. See Figure 5.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS34300( BC )05/96] 8. Before placing the child into the child seat, forcibly tilt the child seat from side-to-side and in forward directions to make sure that the seat is held securely in place. See Figures 6 and 7. If the child seat moves excessively, repeat steps 6 through 8, or properly install the child seat in a different seating position.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 [SS34500( BC )04/96] half page art:0011369-A *[SS34600( BC )05/96] 9. % [SS34700( BC )05/96] Installing a Child Safety Seat at the Rear Center Seating Position with Adjustable Lap Belt *[SS34800( BCGV)01/96] 1. Lengthen the lap belt. To lengthen the belt, hold the tongue so that its bottom is perpendicular to the direction of webbing while sliding the tongue up the webbing. *[SS34900( BCGV)01/96] 2.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS35100( BCGV)01/96] 4. Insert the belt tongue into the proper buckle for the center seating position until you hear a snap and feel it latch. Make sure the tongue is securely fastened to the buckle by pulling on tongue. *[SS35200( BCGV)01/96] 5. Push down on the child seat while pulling on the loose end of the lap belt webbing to tighten the belt. [SS35300( BCGV)12/95] 6.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS35400( ALL)01/96] *[SS35500( ALL)01/96] % Safety Belts for Children Children who are too large for child safety seats should always wear safety belts. (See instructions with your child seat, or contact its manufacturer, to determine maximum size of child that will safely fit in the seat.
File:06rcssc.ex Update:Fri Jun 7 13:59:45 1996 *[SS36000( ALL)01/96] To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards. Belt-positioning booster seats raise the child and provide a shorter, firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child.
File:08rctoc.ex Update:Thu May 30 10:28:08 1996 Starting % *[TO00200( ALL)01/96] *[TO00300( ALL)01/96] *[TO00400( ALL)01/96] % [TO00500( ALL)01/96] * *[TO00600( ALL)02/96] Fuel-Injected Engines When starting a fuel-injected engine, the most important thing to remember is to avoid pressing down on the accelerator before or during starting. Only use the accelerator when you have problems getting your vehicle started.
File:08rctoc.ex Update:Thu May 30 10:28:08 1996 *[TO01300( ALL)02/96] Before you start your vehicle, you should test the warning lights on the instrument panel to make sure that they work. Refer to the Instrumentation chapter. *[TO01400( ALL)01/96] *[TO01500( ALL)01/96] *[TO01600( ALL)01/96] Starting Your Engine 1. Follow the steps under Preparing to Start Your Vehicle at the beginning of this section. *[TO01700( ALL)01/96] *[TO01800( ALL)01/96] 2. Turn the ignition key to the ON position. 3.
File:08rctoc.ex Update:Thu May 30 10:28:08 1996 *[TO02400( ALL)01/96] *[TO02500( ALL)01/96] For a warm engine: *[TO02600( ALL)01/96] Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the starter. *[TO02700( ALL)01/96] After you start the engine, let it idle for a few seconds. Keep your foot on the brake pedal and put the gearshift lever in gear. Release the parking brake. Slowly release the brake pedal and drive away in the normal manner.
File:08rctoc.ex Update:Thu May 30 10:28:08 1996 *[TO03600( ALL)01/96] A computer system controls the engine’s idle speed. When you start your vehicle, the engine’s idle speed normally runs higher than when it’s warmed up. These faster engine speeds will make your vehicle move slightly faster than its normal idle speed. It should, however, slow down after a short time. If it does not, have the idle speed checked.
File:08rctoc.ex Update:Thu May 30 10:28:08 1996 *[TO04300( ALL)01/96] To turn the heater on, simply plug it into a grounded 110-volt outlet. Ford recommends that you use a 110-volt circuit that is protected by a ground fault circuit interrupter. *[TO04400( ALL)01/96] RWARNING To prevent electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters.
File:08rctoc.ex Update:Thu May 30 10:28:08 1996 *[TO05100( ALL)01/96] Have the exhaust and body ventilation systems checked whenever: *[TO05200( ALL)01/96] *[TO05300( ALL)01/96] *[TO05400( ALL)01/96] *[TO05500( ALL)01/96] ❑ your vehicle is raised for service ❑ the sound of the exhaust system changes ❑ your vehicle has been damaged in a collision Improve your ventilation by keeping all air inlet vents clear of snow, leaves, and other debris.
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 Driving % *[GF00500( ALL)05/96] % [GF00600( ALL)01/96] * Brakes Applying the Brakes [GF00700( ALL)12/95] Braking non ABS models [GF01000( C )12/95] Your vehicle has power front disc brakes and rear drum brakes. Anti-lock disc brakes on all four wheels are optional. They adjust automatically as the brake pads or linings wear down. *[GF01200( ALL)01/96] Apply the brake pedal gradually.
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 *[GF01600( ALL)01/96] Do not drive with your foot resting on the brake pedal; you will wear out the linings and increase your vehicle’s stopping distance. Brake rotor damage may also eventually occur. *[GF01700( ALL)02/96] NOTE: If you are driving down a long or steep hill, shift to a lower gear and do not apply your brakes continuously. If you apply your brakes continuously, they may overheat and become less effective.
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 [GF02500( BC )12/95] To set the parking brake while parking your vehicle, apply the brake pedal with your right foot and hold it while you push the parking brake down firmly with your left foot. The brake system warning light will glow. [GF02800( BC )12/95] one third page art:0010315-A The parking brake *[GF03100( BCGV)05/96] RWARNING Always set the parking brake fully and make sure the gearshift is latched in P (Park).
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 *[GF03700( ALL)02/96] RWARNING If the parking brake is fully released, but the Brake System light remains on, have the brakes checked immediately. They may not be working properly. [GF03800( ALL)12/95] The parking brake system is designed for static parking only and is not designed to stop a moving vehicle, but you can use the parking brake to stop your vehicle in an emergency if the normal brakes fail.
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 % *[GF04300( BCGV)03/96] *[GF04400( BCGV)03/96] Traction Assist TM (If equipped) Your vehicle may be equipped with the optional Traction AssistTM system. This system helps prevent wheel spin in order to improve tire traction and is an especially useful feature when you drive in hilly areas or on slippery, icy or snowy roads.
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 [GF04800( BCGV)12/95] During the Traction AssistTM function, which most often occurs during low speed acceleration on slippery surfaces, a noise may be heard coming from the engine compartment. This noise is created by the ABS pump and is normal and may last for a few seconds during the acceleration of the vehicle. [GF04900( BCGV)05/96] In general, this system improves your vehicle’s stability and acceleration performance when road conditions warrant.
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 *[GF05500( ALL)01/96] Never hold the steering wheel to the extreme right or left for more than five seconds if the engine is running. This can damage the power steering pump. [GF05600( BCGV)12/95] Speed Sensitive Power Steering (If equipped) [GF05800( BC )12/95] The steering system in 4.6L engine vehicles is speed sensitive. This means that the steering effort is light for parking and heavier for highway driving.
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 % Your vehicle is equipped with a Brake Shift Interlock safety feature. This feature prevents the gearshift from being moved from the P (Park) position until the brake pedal is depressed. This feature is active when the ignition is in the ON position. If the gearshift lever CANNOT be moved from P (Park) with the brake pedal depressed: *[GF07700( ALL)12/95] 1. Turn the engine off and remove the ignition key. *[GF07800( ALL)12/95] *[GF07900( ALL)04/96] 2.
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 % [GF08600( BC )12/95] half page art:0010307-F The positions of the console-mounted gearshift *[GF08700( ALL)01/96] Once the gearshift is secure in the desired position, release the brake pedal and use the accelerator as necessary. *[GF08800( ALL)05/96] *[GF08900( ALL)05/96] R (Reverse) *[GF09000( ALL)01/96] N (Neutral) [GF09100( ALL)12/95] As in P (Park), there is no power transferred through the transmission.
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 % Driving [GF09400(MBC )05/96] Your vehicle’s gearshift is console-mounted on the floor. The Transmission Control Switch (TCS) is located on the gearshift handle. The Transmission Control Indicator Light (O/D OFF) is located on the instrument panel. You can put the gearshift lever in any of the several positions. [GF09700(MBC )12/95] The OVERDRIVE OFF light is off (not illuminated) during normal vehicle operation.
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 *[GF10400( ALL)12/95] However, Overdrive also shifts into a fourth gear —an overdrive gear — when your vehicle cruises at an appropriate consistent speed for any length of time. This fourth gear will increase your fuel economy when you travel at cruising speeds.
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 *[GF11700( ALL)05/96] RWARNING Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn off the ignition whenever you leave your vehicle. *[GF11800( ALL)05/96] RWARNING Never leave your vehicle unattended while it is running. *[GF12000(MBC )12/95] You can tell a console-mounted gearshift is securely latched in P (Park) if the lever is adjacent to the P (Park) and you cannot move it without pushing in the thumb button.
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 *[GF15900( ALL)01/96] RWARNING Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label.
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 *[GF17100( ALL)11/92] After determining this load, you must also make sure that the total weight of your vehicle, plus the load it carries, is less than its GVWR. Also, make sure that the weight your vehicle carries over each axle is less than the GAWR for the respective axle. *[GF17200( ALL)01/96] If your vehicle exceeds the GVWR, remove cargo from your vehicle accordingly.
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 *[GF18100( ALL)05/96] ❑ Service your vehicle more frequently if you *[GF18200( ALL)05/96] Ten to 15% of the loaded trailer’s weight should be on the tongue. However, the tongue load should never exceed 10% of the maximum weight that your vehicle can safely tow. *[GF18300( ALL)05/96] RWARNING tow a trailer. (See Servicing your vehicle if you tow in this chapter.) Do not tow a trailer when using a temporary spare tire.
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 *[GF19300( ALL)05/96] Always check the pressure in all your vehicle’s tires when preparing to tow (see inflation recommendation on the tire label). *[GF19400( ALL)05/96] *[GF19500(MBC )12/95] Using the hitch *[GF20000( ALL)05/96] Tie down the load so that it does not shift and change the weight on the hitch. This will prevent damage to your vehicle and make your vehicle easier to handle.
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 *[GF21600( ALL)05/96] *[GF21700( ALL)05/96] Connecting the trailer’s brakes Electric brakes and manual, automatic, or surge-type hydraulic brakes are safe if you install them properly and adjust them according to the manufacturer’s instructions. Be sure that your trailer’s brakes meet local and federal regulations. *[GF21900( ALL)05/96] RWARNING % Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system.
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 % If you use the speed control while you are towing on very long, steep grades, the speed control may shut off. [GF23200( ALL)05/96] Servicing Your Vehicle If You Tow *[GF23300( ALL)05/96] If you tow a trailer for a long distance, your vehicle will need to be serviced more frequently than usual. Refer to the Maintenance Schedule booklet for additional information.
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 *[GF24000( ALL)01/96] % [GF24100( ALL)01/96] * *[GF24200( ALL)01/96] *[GF24300( ALL)01/96] Driving in Bad Weather *[GF24400( ALL)01/96] *[GF24500( ALL)01/96] *[GF24600( ALL)01/96] ❑ Drive slower than you normally would. ❑ Do not use speed control. ❑ Give your vehicle more distance to stop.
File:09rcgfc.ex Update:Mon Jun 3 09:26:27 1996 [GF25500( ALL)12/95] By moving the vehicle backward and forward, you may gain enough momentum to move out of the spot. Do not rock the vehicle for more than a few minutes. This may overheat the engine, damage the transmission, or damage the tires. If you are still stuck after a minute or two of rocking, call for a tow truck. *[GF25600( ALL)01/96] *[GF25700( ALL)01/96] High water *[GF25800( ALL)01/96] If you must drive through high water, drive slowly.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 Roadside Emergencies [ER00175( ALL)03/96] Hazard Flashers *[ER00200( ALL)01/96] The flashers work whether your vehicle is running or not. The flashers work for up to two hours when the battery is fully charged and in good condition without draining the battery excessively. If the flashers run for longer than two hours or if the battery is not fully charged, the battery can be drained.
File:10rcerc.
File:10rcerc.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 *[ER02300( ALL)12/95] *[ER02400( ALL)12/95] High Current Fuses *[ER02500(MBC )12/95] The high current fuse panel is located in the engine compartment on the left-hand fender apron. % High current fuses are circuit protectors that are part of the wiring harness for some electrical equipment. These, like fuses, open when the circuit load exceeds their amperage rating. High current fuses may be purchased from your Ford or Lincoln-Mercury dealer.
File:10rcerc.
File:10rcerc.
File:10rcerc.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 *[ER04400( ALL)01/96] *[ER04500( ALL)01/96] Checking and Replacing Fuses [ER04700( BC )12/95] 1. Find the fuse panel underneath the instrument panel, to the left of the steering column. [ER05000( BCGV)12/95] 2. Check the fuse to see if it is blown. Look through the clear side of the fuse to see if the metal wire inside is separated. If it is, the fuse should be replaced.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 [ER05800( BC )12/95] eight pica chart:0011219-A *[ER05900( ALL)01/96] RWARNING Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. [ER06000( BC )12/95] 4. *[ER06300( BCGV)04/96] Even after you replace a fuse, it may continue to blow if you do not find what caused the overload.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 *[ER06800( ALL)01/96] If you replace a circuit breaker, use one with the same amperage rating. To remove a circuit breaker mounted in the fuse panel, grip it with your finger and thumb and pull it straight out of its socket.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 *[ER08100( ALL)03/96] RWARNING If you see or smell fuel, do not reset the switch or try to start your vehicle. Have all the passengers get out of the vehicle and call the local fire department or a towing service. *[ER08200( ALL)03/96] If your engine cranks but does not start after a collision or substantial jolt: *[ER08300( ALL)01/96] *[ER08400( ALL)03/96] *[ER08500( ALL)01/96] 1. Turn the ignition key to the OFF position. 2.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 % The Temporary Spare Tire [ER09700(MBC )02/96] You have a high pressure temporary spare tire. This spare tire is smaller than a regular tire and is designed for emergency use only. Use it only when you get a flat tire and replace it as soon as you can. This spare tire is marked with the words “TEMPORARY USE ONLY” so that you can easily identify it.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 *[ER10600( ALL)02/96] *[ER10700(MBCG )02/96] ❑ use the wheel for any other type of vehicle. ❑ drive through an automatic car wash with this tire. Because the temporary spare tire is smaller than a conventional tire, it reduces the ground clearance. Your vehicle may get caught in the rails and it could be damaged. % Spare Tire Location [ER11100( ALL)02/96] The spare is stored in the trunk.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 *[ER11500( ALL)03/96] *[ER12000( BC )03/96] *[ER12100( BC )03/96] To remove the spare tire: *[ER12200( BC )03/96] NOTE: Wing-nut is not removable. [ER12300( BC )03/96] 3. *[ER12700( ALL)03/96] *[ER12900( BCGV)03/96] Preparing to Change the Tire *[ER13100( BCGV)03/96] When one of the back wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park).
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 *[ER13700( ALL)01/96] 2. Get out the spare tire and jack. [ER13900( BC )12/95] 3. Remove any optional wheel covers or hubcaps with the tapered end of a wheel nut wrench. Insert the handle of the wrench and twist it against the inner wheel cover flange. For more about removing wheel covers, see the information later in this chapter. *[ER14200(MBC )12/95] 4.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 [ER15000( ALL)12/95] half page art:0010759-A The improper lift point *[ER15100( ALL)05/96] NOTE: Never use the differential housing as a lift point.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 % [ER15200( BC )12/95] half page art:0010346-C The notches for the jack *[ER15600( ALL)12/95] 2. Turn the jack handle clockwise until the wheel clears the ground. Remove the wheel lug nuts. *[ER15700(MBC )03/96] 3. Replace the flat tire with the spare tire, making sure that the air valve stem is facing outward. *[ER15800(MBC )03/96] 4. Reinstall the lug nuts, tightening until the wheel is snug against the hub.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 *[ER16000(MBC )03/96] 6. Remove the jack and fully tighten the lug nuts in the order shown in the following illustration. As soon as possible, have your dealer or a qualified service technician check the lug nuts for proper torque specifications. % [ER16100( ALL)12/95] quarter page art:0010350-A The lug nuts on the wheel *[ER16200(MBC )03/96] 7. Place any wheel covers and ornaments in the trunk. *[ER16300(MBC )03/96] 8.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 % [ER16900( BC )04/96] Center Wheel Cover [ER17000( BC )04/96] To remove the wheel cover: [ER17100( BC )12/95] 1. Pry the center ornament from the wheel cover using the tapered end of the jack handle. Do not use a screwdriver or any other tool. If you do, you may damage the cover. The wheel, with the wheel cover still attached, may now be removed from the vehicle by removing the five lug nuts. [ER17200( BC )12/95] 2.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 [ER17400( BC )04/96] To replace the wheel cover: [ER17500( BC )12/95] 1. Place the tire valve stem hole in the wheel cover over the tire valve stem. Align the holes in the wheel cover mounting pad with the center holes in the metal inserts. Install and tighten the five screws. [ER17600( BC )12/95] 2. Align the legs of the ornament with the slots on the wheel cover. Strike the ornament with the palm of your hand.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 *[ER19400(MBC )12/95] *[ER19500(MBC )02/96] Removing the anti-theft lug nut *[ER19600(MBC )12/95] Place the lug nut wrench over the lug nut key and apply pressure on the key with the wrench. Turn the wrench in a counterclockwise direction to remove the lug nut.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 *[ER20200( ALL)02/96] % RWARNING Applying too much pressure on the ends when lifting a battery could cause acid to spill. Lift the battery with a carrier or with your hands on the opposite corners. *[ER20300( ALL)02/96] % RWARNING Batteries contain sulfuric acid which burns skin, eyes, and clothing. *[ER20400( ALL)02/96] If the acid touches someone’s skin, eyes, or clothing, immediately flush the area with water for at least 15 minutes.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 % Preparing Your Vehicle [ER20700( ALL)02/96] NOTE: also see label on battery. *[ER20800( ALL)02/96] 1. Your vehicle has a 12-volt starting system, so you need to use a 12-volt jumper system. You will damage your starting motor, ignition system, and other electrical parts if you connect them to a 24-volt power supply (either two 12-volt batteries in series or a 24-volt generator set). *[ER20900( ALL)02/96] 2.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 *[ER21300( ALL)02/96] *[ER21400( ALL)02/96] Connecting the jumper cables 1. Connect one end of the first jumper cable to the positive (+) terminal of the discharged battery. (You can connect either jumper cable to the positive (+) terminal, as long as you use the same cable for both positive terminals.) Most jumper cables have a red cable and a black cable. The red cable is generally used for the positive terminals and the black for the negative ones.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 [ER22000( BC )02/96] full page art:0010334-D The 3.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 [ER22100(BC )04/96] full page art:0010666-G The 4.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 *[ER22300( ALL)02/96] *[ER22400( ALL)02/96] Jump-Starting 1. Make sure that the jumper cables are not in the way of moving engine parts, then start the booster vehicle. Run the engine at a moderate speed. *[ER22500( ALL)02/96] 2. Let the discharged battery charge for a few minutes and then start the disabled vehicle. It may take a couple of tries before the vehicle starts.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 % *[ER23500( ALL)04/96] *[ER23600( ALL)01/96] [ER23660( BC )03/96] Towing Your Vehicle If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. Do not tow with slingbelt equipment when towing your Cougar from the rear. Ford Motor Company has not developed or approved a T-hook sling-type procedure.
File:10rcerc.ex Update:Thu May 30 10:30:02 1996 *[ER23700( BC )04/96] three fourths page art:0011391-A *[ER23800( ALL)01/96] When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Company for all authorized tow truck operators. Have your tow truck driver refer to this manual for the proper hook-up and towing procedures for your vehicle.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 Maintenance and Care % Service Made Easy *[MC00200( ALL)01/96] *[MC00300( ALL)01/96] *[MC00400( ALL)01/96] Ford has two goals for servicing your vehicle. 1. When we can, we design parts that do not need to be serviced. *[MC00500( ALL)01/96] 2. We want to make servicing your vehicle as easy as possible.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 vibration, or other indication that your vehicle may need service. If you do notice something unusual, see that your vehicle is serviced promptly. *[MC01200( ALL)01/96] Use only recommended fuels, lubricants, fluids, and service parts conforming to Ford specifications. Motorcraft parts are designed and built to provide the best performance in your vehicle. Using these parts for replacement is your assurance that Ford-built quality stays in your vehicle.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC01900( ALL)01/96] ❑ Do not work on a vehicle in an enclosed *[MC02000( ALL)01/96] ❑ Never get under a vehicle while it is *[MC02100( ALL)01/96] ❑ Keep all lit cigarettes and other smoking *[MC02200(MBC )01/96] If you disconnect the battery, the engine must “relearn” its idle conditions before your vehicle will drive properly. To find out how the engine does this, see Battery in this chapter.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 % Opening the Hood [MC03400( ALL)12/95] 1. Inside the vehicle, pull the hood release located under the lower left corner of the instrument panel. [MC03600( ALL)12/95] 2. Go around to the front of the vehicle, and release the auxiliary catch that is located under the front edge of the hood at the center of the vehicle.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 [MC05300( BC )12/95] full page art:0010327-C A 3.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 [MC05400( BC )12/95] full page art:0010665-G A 4.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 % *[MC05600( ALL)01/96] *[MC05700( ALL)01/96] Engine Oil Recommendations We recommend using Motorcraft oil or an equivalent oil meeting Ford Specification WSS-M2C153-F and displaying the American Petroleum Institute CERTIFICATION MARK on the front of the container.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC06500( ALL)01/96] *[MC06600( ALL)01/96] Checking and Adding Engine Oil *[MC06700( ALL)01/96] *[MC06800( ALL)01/96] Checking the engine oil level: 1. Turn the engine off after it has warmed up and allow a few minutes for the engine oil to drain back into the oil pan. *[MC06900( BCGV)01/96] 2. Set the parking brake, making sure the gearshift is securely latched in P (Park). *[MC07100( ALL)01/96] 3. Open the hood. Protect yourself from engine heat.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC07700( BCGV)03/96] 6. Carefully pull the dipstick out again. If the oil level is below the “ADD 1 QT” line, add engine oil as necessary. If the oil level is beyond the letter “F” in Full, engine damage or high oil consumption may occur and some oil must be removed from the engine. *[MC07800( ALL)01/96] 7. Put the dipstick back in and make sure it is fully seated. *[MC07900( ALL)01/96] It may be necessary to add some oil between oil changes.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC08350( ALL)05/96] NOTE: Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, startup engine noises or knock may be experienced. It is recommended you use the appropriate “Motorcraft” oil filter (or another brand meeting Ford specifications) for your engine application.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 see The Engine Types in the Index.) The fluid level should be between the MAX fill mark and 3/8" below the MAX fill line. *[MC09200( ALL)01/96] RWARNING Brake fluid is toxic. *[MC09300( ALL)01/96] *[MC09400( ALL)03/96] % *[MC09500( ALL)01/96] If brake fluid contacts eyes, flush eyes with running water for 15 minutes. Get medical attention if irritation persists. If taken internally, drink water and induce vomiting. Get medical attention immediately.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC10100( ALL)01/96] If you find that the fluid level is excessively low — below the seam or ridge on the outside of the plastic reservoir — have the brake system inspected. *[MC10200( ALL)01/96] RWARNING Do not let the reservoir for the master cylinder run dry. This may cause the brakes to fail.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 % Use specially formulated windshield washer fluid rather than plain water, because specially formulated washer fluids contain additives that dissolve road grime. For safety reasons, washer fluids containing an appropriate antifreeze such as methanol should be used in freezing weather (temperatures below 32˚F [0˚C]). State or local regulations on Volatile Organic Compounds (VOCs) may restrict use of the most common antifreeze, methanol.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC12300( ALL)02/96] The coolant additives also protect the entire cooling system from internal passageway corrosion and these additives lubricate the water pump. The coolant should be serviced as noted in the Maintenance Schedule booklet.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC12900( ALL)05/96] *[MC13000( ALL)05/96] Adding Engine Coolant RWARNING Do not put engine coolant in the container for the windshield washer fluid. *[MC13100(MBC )05/96] If sprayed to clean the glass, engine coolant or antifreeze could make it difficult to see through the windshield. [MC13200(MBC )05/96] RWARNING Never remove the radiator cap or vent plug while the engine is running or hot.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC14505( ALL)05/96] Use Ford Premium Cooling System Fluid E2FZ-19549-AA (in Canada, Motorcraft CXC-8-B) or an equivalent premium engine coolant that meets Ford specification ESE-M97B44-A. Ford Premium Engine Coolant is an optimized formula that will protect all metals and rubber elastomers used in Ford cooling systems for 4 years or 50,000 miles (80,000 km).
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC15005( ALL)05/96] *[MC15105( ALL)05/96] Severe winter climate If you drive in extremely cold climates (less than -34˚F [-36˚C]), it may be necessary to increase the coolant concentration above 50%. Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle is such that the coolant will not freeze at the temperature level in which you drive during winter months. Never increase the engine coolant concentration above 60%.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 [MC15700(MBC )12/95] 3.8L engine only [MC15800(MBC )12/95] ❑ Open the vent plug. ❑ Remove coolant recovery reservoir cap. ❑ Remove radiator pressure cap. ❑ With the engine off and cool, add a 50/50 [MC15900(MBC )12/95] [MC16000(MBC )12/95] [MC16100(MBC )12/95] mixture of recommended cooling system fluid and water to the radiator until full, then add to the reservoir until the reservoir is at the FULL-HOT level.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC17000(MBC )12/95] ❑ Check for leaks at the draincock, block plug *[MC17100(MBC )12/95] ❑ Recheck the engine coolant level, using the [MC17200( BC )12/95] 4.6L engine only *[MC17400( ALL)12/95] ❑ With the engine OFF and cool, remove the *[MC17500( ALL)12/95] ❑ Add a 50/50 mixture of specified coolant and [MC17600( ALL)12/95] ❑ Continue to fill the reservoir until the coolant and vent plug.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC18000( ALL)12/95] *[MC18100( ALL)12/95] *[MC18200( ALL)12/95] ❑ Reinstall the pressure cap securely. ❑ Check for leaks at the draincock. ❑ Recheck the engine coolant level, using the *[MC18300( ALL)01/96] *[MC18400( ALL)01/96] Power Steering Fluid % recommended procedure, after one or two occasions of vehicle use. Check the level of the power steering fluid at least twice a year (i.e., every Spring and Fall).
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC19400(MBC )03/96] 6. When you are finished, put the dipstick back in and make sure that it fits snugly. [MC19600(MBC )12/95] half page art:0010485-C The dipstick for power steering fluid [MC19900( ALL)05/96] Use only power steering fluid that meets Ford Specification MerconH ATF XT-2-QDX or an equivalent. *[MC20000( ALL)01/96] If the power steering fluid is low, do not drive your vehicle for a long period of time before adding fluid.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 [MC20300( BC )03/96] 4.6L SFI engine [MC20400(MBC )12/95] 1. Check the fluid level when the system is COLD (allow at least one half hour after driving for the power steering fluid to cool). [MC20500(MBC )04/96] 2. Locate the power steering reservoir mounted to the front upper left-hand corner of the engine. [MC20600(MBC )12/95] 3. Visually verify that the fluid level is above the MIN line adjacent to the reservoir “sight window.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 [MC21100(MBC )05/96] Use only power steering fluid that meets Ford Specification MerconH ATF XT-2-QDX or an equivalent. *[MC21200(MBC )01/96] NOTE: If the power steering fluid is low, do not drive your vehicle for a long period of time before adding fluid. This can damage the power steering pump.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 [MC21900(MBC )12/95] NOTE: Your vehicle should not be driven if the fluid level is below the low cold reading on the dipstick. *[MC22000( ALL)01/96] Wipe off the dipstick cap, pull the dipstick out and wipe the indicator end clean. Put the dipstick back into the filler tube and make sure it is fully seated. Pull the dipstick out and read the fluid level.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 [MC22800(MBC )12/95] one third page art:0011152-A Detail of the automatic transmission dipstick % *[MC23200( ALL)01/96] *[MC23300( ALL)01/96] Battery Your vehicle may have a Motorcraft maintenance-free battery. When the original equipment battery is replaced under warranty, it may be replaced by a Motorcraft Low-Maintenance Battery.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC23600( ALL)01/96] *[MC23700( ALL)01/96] % Help Us Protect Our Environment Ford Motor Company strongly recommends that used lead-acid batteries be returned to an authorized recycling facility for disposal. *[MC23800( ALL)01/96] one inch art:0000983-A Battery recycling symbol % Because your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 not use fuel, kerosene, paint thinner, or other solvents to clean your wiper blades. These will damage your blades. *[MC24600( ALL)01/96] To make reaching the wiper blades easy, simply turn the ignition to the ACC position and turn your wipers on. Wait for them to reach a vertical position and turn the ignition to the OFF position. Do not move the wipers manually. Manually moving the wipers across the windshield may damage them.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC26000( ALL)01/96] *[MC26100( ALL)01/96] Tire Rotation *[MC26200( ALL)05/96] For tire rotation intervals, see the Maintenance Schedule booklet. If you notice that the tires wear unevenly, have them checked. % Because your vehicle’s front and rear tires perform different jobs, they often wear differently. To make sure your tires wear evenly and last longer, rotate them as indicated in the following diagram.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC26800( ALL)01/96] *[MC26900( ALL)01/96] % Replacing the Tires Replace any tires that show wear bands. When your tire shows a wear band, it has only 1/16 inch (2 mm) of tread left. % [MC27000( ALL)12/95] one inch art:0001318-A A worn-out tire *[MC27100( ALL)02/96] Because your vehicle’s tires may wear unevenly, you may need to replace them before a wear band appears across the entire tread.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC27400( ALL)01/96] *[MC27500( ALL)01/96] Information About Tire Quality Grades *[MC27600( ALL)01/96] Tire Quality Grades apply to new pneumatic tires for use on passenger cars. They do not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). *[MC27700( ALL)01/96] U.S.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC28000( ALL)01/96] *[MC28100( ALL)05/96] *[MC28150( ALL)05/96] Traction A B C The traction grades, from highest to lowest, are A, B, and C, and they represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC28325( ALL)05/96] RWARNING The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. *[MC28350( ALL)03/96] RWARNING Driving too fast for conditions creates the possibility of loss of vehicle control.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC28900( ALL)01/96] Use chains on the tires only in an emergency or if the law requires them where you live. If you choose to use chains on your vehicle’s tires, be aware of the following: *[MC29000( ALL)01/96] ❑ Make sure the chains are the right size for *[MC29200( ALL)01/96] ❑ Put the chains on tightly with the ends held *[MC29300( ALL)01/96] ❑ Drive slowly.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC30100( ALL)01/96] 2. Put the nozzle all the way inside the fuel filler pipe before pumping the fuel. *[MC30200( ALL)01/96] NOTE: If you spill any fuel on the body of your vehicle, clean it off immediately. The fuel may dull or soften the paint if you do not wash it off. % *[MC30300( ALL)03/96] 3. Replace the fuel cap completely when you are finished. Turn it clockwise 1/4 turn until it is tight. It will click when it is fully tightened.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 refuel, your vehicle can be operated on non-California fuels. However, even though your engine will perform adequately on other gasolines, the performance of the emission control devices and systems may be adversely affected. Repair of damage caused by using a fuel that your vehicle was not designed for may not be covered by your warranty.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 your vehicle. We recommend the use of gasolines that meet the AAMA specification if they are available. *[MC31560( ALL)05/96] It should not be necessary to add any aftermarket products to your fuel tank if you continue to use a high-quality fuel.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC32800( ALL)08/95] ❑ If fuel is splashed in the eyes, remove contact *[MC32900( ALL)01/96] Gasoline and gasoline blends may contain small amounts of carcinogens, such as benzene. Long-term exposure to unleaded gasoline vapors has caused cancer in laboratory animals.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC33700( ALL)01/96] *[MC33800( ALL)01/96] To calculate fuel economy: 1. Fill the fuel tank completely and record the initial odometer reading. *[MC33900( ALL)01/96] 2. Every time you buy fuel, record the amount (in gallons or liters) purchased. *[MC34000( ALL)01/96] 3. After at least 3-5 tankfuls, fill the fuel tank and record the final odometer reading. *[MC34100( ALL)01/96] 4.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC35500( ALL)01/96] *[MC35600( ALL)01/96] ❑ Heavy loads ❑ Aftermarket add-ons such as bike, ski or *[MC35700( ALL)12/95] *[MC35800( ALL)12/95] Self-Service Pointers *[MC35900( ALL)12/95] The following procedures require only a tire gauge, a rag, an oil can spout and windshield washer fluid.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC36800( ALL)01/96] To make sure that the catalytic converter and the other emission control parts continue to work properly: *[MC36900( ALL)01/96] *[MC37000( ALL)01/96] *[MC37100( ALL)01/96] ❑ Use only unleaded fuel. ❑ Avoid running out of fuel. ❑ Do not turn off the ignition while your *[MC37200( ALL)01/96] *[MC37300( ALL)02/96] ❑ Do not push start your vehicle.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC37600( ALL)01/96] RWARNING Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. *[MC37700( ALL)01/96] Watch for fluid leaks, strange odors, smoke, loss of oil pressure, the charge warning light, the check engine light, or the temperature warning light. These sometimes indicate that the emission system is not working properly.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC38200( ALL)01/96] Information about your vehicle’s emission control system is on the Vehicle Emission Control Information decal located on or near the engine. This decal identifies engine displacement and gives some tune-up specifications.
File:11rcmcc.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC42700( ALL)01/96] *[MC42800( ALL)03/96] % Headlamp Bulb The headlamps on your vehicle use replaceable bulbs. When the lamp burns out, simply replace the bulb, rather than the whole lamp. *[MC42900( ALL)01/96] RWARNING Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC43400( ALL)03/96] *[MC43500( ALL)01/96] Removing the headlamp bulb 1. Make sure that the headlamp switch is in the OFF position. *[MC43800( BC )01/96] 2. Lift the hood and find the bulb in the headlamp socket. *[MC44100( BC )12/95] 3. Remove the electrical connector from the bulb by grasping the wire with a quick pull rearward. *[MC44300( BC )12/95] 4. Remove the retaining ring by turning it 1/8 of a turn to free it from the socket.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 % High-Mount Brakelamp Bulbs [MC45800( BCGV)12/95] Your vehicle has a brakelamp mounted in the rear window, called a high-mount brakelamp. You may need to remove this lamp at times to replace the brakelamp bulb or to clean the rear window.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 % [MC46200( BCGV)12/95] To remove the high-mount brakelamp: [MC46300( BC )12/95] 1. Slide the trim cover toward the front of the vehicle to disengage the retaining clips. [MC46500( BC )12/95] 2. Twist the socket counterclockwise and remove from lamp. [MC46800( BC )12/95] 3. Pull bulb out of socket. [MC47000( BC )12/95] 4. Remove the retaining screw. [MC47100( BC )12/95] 5. Lift the lamp above the carpet and slide away from the rear window.
File:11rcmcc.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 % *[MC48700( ALL)04/96] *[MC48800( ALL)01/96] Cleaning Your Vehicle Pollen, bird droppings and tree sap can damage the paint, especially in hot weather. Wash your vehicle as often as necessary to keep it clean. *[MC48900( ALL)01/96] Take similar precautions if your vehicle is exposed to chemical industrial fallout.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC49800( ALL)01/96] *[MC49900( ALL)12/95] Cleaning Chrome and Aluminum Parts *[MC50000( ALL)01/96] *[MC50100( ALL)01/96] Cleaning Plastic Parts *[MC50200( ALL)01/96] Do not clean plastic parts with thinners, solvents or petroleum-based cleaners. % % Wash chrome and aluminum parts with a mild detergent. Do not use steel wool, abrasive cleaners, fuel, or strong detergents. Some of your vehicle’s exterior trim parts are plastic.
File:11rcmcc.ex Update:Mon Jun 3 09:27:52 1996 *[MC50900( ALL)02/96] *[MC51000( ALL)02/96] Cleaning the Interior Lamps *[MC51100( ALL)02/96] *[MC51200( ALL)01/96] Cleaning the Instrument Panel Lens *[MC51250( ALL)03/96] *[MC51300( ALL)01/96] *[MC51400( ALL)01/96] Cleaning the Seats *[MC51500( ALL)05/96] *[MC51600( ALL)05/96] Fabric *[MC51700( ALL)05/96] NOTE: Before using any cleaner, test it on a small, hidden area of fabric.
File:11rcmcc.
File:12rccsc.ex Update:Thu May 30 10:31:57 1996 Capacities and Specifications *[CS00200( ALL)01/96] *[CS00300( ALL)01/96] % Refill Capacities, Motorcraft Parts, and Lubricant Specifications Motorcraft Parts % [CS00500( BC )05/96] fourteen pica chart:0010452-N [CS00700( ALL)12/95] If a spark plug is removed for examination, it must be reinstalled in the same cylinder. [CS00800(MBC )12/95] For 3.8L engines: [CS00900(MBC )12/95] Cylinders #1, #2, #3 have an EG suffix.
File:12rccsc.ex Update:Thu May 30 10:31:57 1996 *[CS01800( ALL)02/96] % Fluid Specifications and Capacities [CS02000( BC )05/96] twenty-two pica chart:0010447-P *[CS02200( ALL)05/96] NOTE: Rear axle lube quantities must be replaced every 100,000 miles (160,000 km) or if the axle has been submerged in water. Otherwise, the lube should not be checked or changed unless a leak is suspected or repair required.
File:12rccsc.
File:12rccsc.ex Update:Thu May 30 10:31:57 1996 % *[CS03000( ALL)01/96] *[CS03100( ALL)01/96] *[CS03200( ALL)01/96] Vehicle Storage Maintenance Tips If you plan on storing your vehicle for an extended period of time (60 days or more), refer to the following maintenance recommendations to ensure your vehicle stays in good operating condition.
File:12rccsc.ex Update:Thu May 30 10:31:57 1996 *[CS04200( ALL)01/96] ❑ Lubricate all hood, door and trunk lid hinges *[CS04300( ALL)01/96] *[CS04400( ALL)01/96] ❑ Cover interior soft trim to prevent fading.
File:12rccsc.ex Update:Thu May 30 10:31:57 1996 *[CS05200( ALL)01/96] *[CS05300( ALL)01/96] % [CS05400( ALL)01/96] * *[CS05500( ALL)01/96] *[CS05600( ALL)01/96] Cooling system *[CS05700( ALL)12/95] ❑ If storing your vehicle for more than 30 days [CS05800( ALL)12/95] NOTE: If battery cables are disconnected, it will be necessary to reset memory features.
File:12rccsc.
File:13rcrdc.ex Update:Thu May 30 10:31:59 1996 Reporting Safety Defects (U.S. Only) *[RD00300( ALL)03/96] If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company.
File:14rchsc.ex Update:Thu May 30 10:32:19 1996 Customer Assistance % *[HS00205( ALL)05/96] *[HS00210( ALL)11/95] *[HS00215( ALL)06/94] *[HS00220( ALL)06/94] *[HS00225( ALL)06/94] *[HS00230( ALL)06/94] *[HS00235( ALL)06/94] *[HS00240( ALL)06/94] Roadside Assistance Ford Motor Company has set up a 24-hour, seven-day-a-week hotline with trained operators who put you in touch with the help you need if you experience a problem with your vehicle.
File:14rchsc.ex Update:Thu May 30 10:32:19 1996 *[HS00245( ALL)06/94] *[HS00250( ALL)06/94] How to use Roadside Assistance *[HS00255( ALL)04/95] To receive roadside assistance in the United States call 1-800-241-FORD (in Canada call 1-800-665-2006). *[HS00260( ALL)04/95] Should you need to arrange for roadside assistance yourself, Ford Motor Company will reimburse the reasonable cost. To obtain information about reimbursement call 1-800-241-FORD (in Canada call 1-800-665-2006).
File:14rchsc.ex Update:Thu May 30 10:32:19 1996 *[HS01000( ALL)03/95] If you are away from home when your vehicle needs to be serviced, or if you need more help than the dealer gave you, contact the Ford Customer Assistance Center to find an authorized dealership that may be able to help. *[HS01025( ALL)04/95] % [HS01050( ALL)03/95] * In the U.S.
File:14rchsc.ex Update:Thu May 30 10:32:19 1996 [HS01800( ALL)05/95] one inch art:0010630-A Vehicle Identification Number (VIN/Serial Number) *[HS02200( ALL)05/96] If you still have a complaint involving a warranty dispute, you may wish to contact the Dispute Settlement Board (U.S. only) or the Canadian Motor Vehicle Arbitration Plan (CAMVAP) in Canada.
File:14rchsc.
File:14rchsc.ex Update:Thu May 30 10:32:19 1996 *[HS03650( ALL)05/96] Complaints involving vehicles in which applicable new vehicle limited warranties have expired at receipt of your application are not eligible. Eligibility may differ according to state law. For example, see the unique brochures for California and Wisconsin purchasers/lessees.
File:14rchsc.
File:14rchsc.ex Update:Thu May 30 10:32:19 1996 *[HS05601( ALL)05/96] *[HS05701( ALL)05/96] Making a decision *[HS05801( ALL)05/96] Because the Board usually meets only once a month, some cases may take longer than 30 days to be reviewed. The Board makes every effort to resolve each case within 40 days of receiving the consumer application form. *[HS05901( ALL)05/96] After your case is reviewed, the Board mails you a decision letter.
File:14rchsc.ex Update:Thu May 30 10:32:19 1996 % Ford of Canada Customer Assistance *[HS08800( ALL)08/95] *[HS08900( ALL)03/95] Ford Motor Company of Canada, Limited *[HS08700( ALL)05/95] If you live in Canada and have any questions or concerns that the dealership cannot answer, contact the Customer Assistance Centre.
File:14rchsc.ex Update:Thu May 30 10:32:19 1996 *[HS09400( ALL)09/95] In the CAMVAP program, impartial third-party Arbitrators conduct hearings at mutually convenient times and places in an informal environment. These impartial Arbitrators review the positions of the parties, make decisions and, where appropriate, render awards to resolve disputes. CAMVAP decisions are fast, fair and final as the arbitrator’s award is binding on both you and Ford of Canada.
File:14rchsc.ex Update:Thu May 30 10:32:19 1996 *[HS10100( ALL)06/95] You may also have difficulty importing your vehicle back into the U.S. if you use leaded fuel. *[HS10200( ALL)06/95] If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership.
File:15rcacc.ex Update:Thu May 30 10:32:34 1996 Accessories *[AC00200( ALL)05/96] *[AC00240( ALL)01/96] Ford Accessories for Your Vehicle Ford has many fine products available from your dealer to clean your vehicle and protect its finishes. For best results, use the following, or products of equivalent quality: *[AC00280( ALL)01/96] fourteen pica chart:0001433-A *[AC00300( ALL)05/96] A wide selection of accessories is available through your local authorized dealer.
File:15rcacc.
File:15rcacc.ex Update:Thu May 30 10:32:34 1996 *[AC01400( ALL)05/96] NOTE: When adding accessories, equipment, passengers, and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR, GAWR as shown on the Safety Compliance Certification Label). Consult your dealer for specific weight information.
File:15rcacc.ex Update:Thu May 30 10:32:34 1996 *[AC01600( ALL)05/96] NOTE: Mobile communications systems may harm the operation of your vehicle, particularly if they are not properly designed for automotive use or are not properly installed. For example, when operated, such systems may cause the engine to stumble or stall. In addition, such systems may themselves be damaged or their operation affected by operating your vehicle.
File:15rcacc.
File:16rcqic.
File:16rcqic.
File:16rcqic.
File:16rcqic.
File:16rcqic.
File:16rcqic.
File:16rcqic.
File:16rcqic.
File:16rcqic.ex Update:Fri Jun 7 14:00:47 1996 [QI02905( C )05/95] full page art:0011213-D 3.
File:16rcqic.ex Update:Fri Jun 7 14:00:47 1996 [QI03100( C )05/95] full page art:0011347-B 4.
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 Index A ABS warning light (see Anti-lock brake system) . . Accessory position on the ignition Additives, engine oil . . . . . . Air bag supplemental restraint system. . . . . . . . and child safety seats . . . . . description . . . . . . . . . . driver air bag . . . . . . . . indicator light . . . . . . . . operation . . . . . . . . . . passenger air bag . . . . . . . service and information labels . tone generator . . . . . . . . Air cleaner filter location . .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 Anti-theft lug nuts and key. . . . . . Anti-theft system arming the system . . . . . . . . description . . . . . . . . . . . . disarming an untriggered system . . disarming a triggered system. . . . triggering . . . . . . . . . . . . warning light . . . . . . . . . . . Appeals (see Dispute settlement board) Assistance (see Customer assistance). . Audio system (see Electronic sound system) . . . . . . . . . . Autolamp system (see Headlamps) . .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 Battery (continued) voltage gauge . . . . . . . when storing your vehicle . . Brake fluid . . . . . . . . . . brake warning light . . . . . checking and adding . . . . description . . . . . . . . . specifications . . . . . . . . Brakelamp . . . . . . . . . . bulb replacement . . . . . . high-mount brakelamp . . . Brakes . . . . . . . . . . . . adjustment . . . . . . . . . anti-lock . . . . . . . . . . anti-lock brake system (ABS) warning light . . . . . .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 Bulbs, replacing . . . . . halogen . . . . . . . headlamps . . . . . . high-mount brakelamp specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243 244 244 246 248 C Canada, customer assistance . . . . . . . 271 Canada, warranty information . . . . . . . 4 Canadian Motor Vehicle Arbitration Plan (CAMVAP) . . . . . . . . . . . . . . 271 Capacities for refilling fluids . . . . . . .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 Cleaning your vehicle . . . . . . . chrome and aluminum parts . . . engine compartment . . . . . . exterior . . . . . . . . . . . . exterior lamps . . . . . . . . . fabric . . . . . . . . . . . . . headlamps . . . . . . . . . . . instrument panel . . . . . . . . instrument panel lens . . . . . . interior . . . . . . . . . . . . interior lamps . . . . . . . . . mirrors . . . . . . . . . . . . plastic parts . . . . . . . . . . polishing. . . . . . . . . . . .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 Coolant (see Engine coolant) checking and adding . . drain and flush . . . . . preparing for storage . . refill capacities . . . . . specifications . . . . . . temperature gauge . . . Cooling fan . . . . . . . . Customer Assistance Center, Customer Assistance Centre, Ford of Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ford (U.S.) . . . . . . . 213 . 215 . 217 . 258 . 254 . 255 . . 21 . 202 .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 E Electrical system circuit breakers . . . . . . . . . fuses . . . . . . . . . . . . . Electronic sound system tuning the radio . . . . . . . . warranty and service information Electronic stereo cassette radio (see Electronic sound system) . . Emergencies, roadside assistance . . . . . . . . . . . battery acid spills . . . . . . . . fuel . . . . . . . . . . . . . . jump-starting . . . . . . . . . . towing. . . . . . . . . . . . .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 Engine coolant (continued) refill capacities . . . . . . . . . specifications . . . . . . . . . . temperature gauge . . . . . . . Engine coolant temperature gauge . description . . . . . . . . . . . mechanical . . . . . . . . . . . Engine fan . . . . . . . . . . . . Engine oil . . . . . . . . . . . . changing oil and oil filter . . . . checking and adding . . . . . . dipstick . . . . . . . . . . . . disposal . . . . . . . . . . . .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 Ford Motor Company of Canada . . Ford of Canada Customer Assistance Centre . . . . . . . . Foreign registration . . . . . . . . French owner guides, how to obtain Fuel . . . . . . . . . . . . . . . capacity . . . . . . . . . . . . choosing the right fuel . . . . . filling your vehicle with fuel. . . filter, specifications . . . . . . . fuel gauge . . . . . . . . . . . low fuel warning light . . . . . octane rating . . . . . . . . . . quality. . . . . . . . . . .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 G Gas cap (see Fuel cap) . . . . . . . . Gas mileage (see Fuel economy) . . . Gasoline (see Fuel). . . . . . . . . . Gauges, Mechanical engine coolant temperature gauge . fuel gauge . . . . . . . . . . . . odometer . . . . . . . . . . . . . speedometer . . . . . . . . . . . tachometer . . . . . . . . . . . . trip odometer . . . . . . . . . . . GAWR (Gross Axle Weight Rating) calculating . . . . . . . . . . . . definition. . . . . . . . . . . . .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 H Hazard flashers . . . . . . Headlamps aiming . . . . . . . . . autolamp system . . . . bulb specification . . . . checking alignment . . . cleaning . . . . . . . . daytime running lights . flashing . . . . . . . . high beam . . . . . . . replacing bulbs . . . . . turning on and off . . . Head restraints . . . . . . Heating manual heating and air conditioning system . semi-automatic system . High beams indicator light . . . . . operation . . . . . . .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 I Identification Number, Vehicle (VIN) . Idle, relearning . . . . . . . . . . . Ignition chime . . . . . . . . . . . . . . positions of the ignition . . . . . . removing the key . . . . . . . . . Indicator lights and chimes (see Lights) Infant seats (see Safety seats) . . . . . Instrument cluster, mechanical . . . . Instrument panel . . . . . . . . . . cleaning . . . . . . . . . . . . . lighting up panel and interior . . . Interval wipers . . . . . . . . . . .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 Lamps (continued) flashing the lamps . . . . . hazard flashers . . . . . . . headlamps . . . . . . . . . high beams . . . . . . . . high-mount brakelamp . . . illuminated entry system . . illuminated mirrors . . . . . instrument panel, dimming . interior lamps . . . . . . . replacing bulbs . . . . . . . trailer . . . . . . . . . . . Lane change indicator (see Turn Lap belts . . . . . . . . . . . Lights, warning and indicator air bag. . . . . . . . . . .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 Lubricant specifications Lug nuts . . . . . . . anti-theft . . . . . . standard . . . . . . tightening sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184, . . . . . . . . . . . . . . . . . . . . . . 255 184 190 185 188 M Maintenance schedule and record (see separate Maintenance Schedule and Record booklet) . . . . . . . . Maintenance (see Servicing) . . . . . Master cylinder, brakes . . . . . . .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 P Panic alarm feature, remote entry system Parking brake. . . . . . . . . . . . . operation . . . . . . . . . . . . . warning light. . . . . . . . . . . . Parts (see Motorcraft Parts) . . . . . . PCV valve, specifications . . . . . . . Power distribution box (see Fuses) . . . Power door locks . . . . . . . . . . . Power features door locks . . . . . . . . . . . . . mirrors . . . . . . . . . . . . . . moon roof . . . . . . . . . . . . . seats. . . . . . . . . . .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 Remote entry system (continued) panic alarm. . . . . . . . . . . . replacement/additional transmitters. replacing the batteries . . . . . . . Restraints, safety (see Safety restraints) adult. . . . . . . . . . . . . . . child . . . . . . . . . . . . . . . head . . . . . . . . . . . . . . . infant . . . . . . . . . . . . . . Roadside assistance . . . . . . . . . Roadside emergencies . . . . . . . . Rotating the tires . . . . . . . . . . . . . . . .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 Safety seats for children . . . . . . . . and air bags . . . . . . . . . . . . automatic locking mode (retractor) . . . . . . . . . 112, in center seating positions . . . . . . in front seat . . . . . . . . . . . in rear outboard . . . . . . . . . in rear seat. . . . . . . . . . . . . Seat belts (see Safety restraints). . . . . Seats . . . . . . . . . . . . . . . . . adjusting the seat, manual . . . . . . adjusting the seats, power . . . . . .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 Spark plugs, specifications . . . . . Special driving conditions . . . . . Specification chart, lubricants . . . . Speed control turning off . . . . . . . . . . . when towing a trailer . . . . . . Speedometer . . . . . . . . . . . Starting your vehicle preparing to start your vehicle . . starting a cold engine . . . . . . starting after a collision . . . . . starting a warm engine . . . . . starting your vehicle if the battery is disabled . . . . . . . . . .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 Tires (continued) replacing. . . . . . . . . . . . . . rotating . . . . . . . . . . . . . . snow tires and chains . . . . . . . . spare tire . . . . . . . . . . . . . storing your vehicle. . . . . . . . . tire grades . . . . . . . . . . . . . treadwear . . . . . . . . . . . . . wear bands . . . . . . . . . . . . Towing a trailer (see Trailer towing) . . Towing your vehicle . . . . . . . . . using wheel dollies . . . . . . . . . with a tow truck . . . . . . . . .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 U Used engine oil, disposal. . . . . . . . . 210 V Vanity mirror . . . . . . . . . . . . . . . 89 Variable interval wipers . . . . . . . . . . 76 VECI (Vehicle Emission Control Information) decal. . . . . . . . . . . . . . . . . 242 Vehicle Identification Number (VIN) . . . 265 Vehicle loading automatic transmissions . . . . . . . . 163 calculating the load . . . . . . . . . . 163 understanding loading information . . . 162 Vehicle storage . . . . . . . . . .
File:rcixc.ex Update:Mon Jun 3 09:28:38 1996 Weight limits (GAWR, GVWR) . . . . Wheel dollies (see Towing). . . . . . Wheels anti-theft lugnuts . . . . . . . . . cleaning . . . . . . . . . . . . . covers . . . . . . . . . . . . . . inspection and maintenance . . . . lug nuts . . . . . . . . . . . . . ornaments . . . . . . . . . . . . Windows . . . . . . . . . . . . . . power windows, operating . . . . rear, defrosting . . . . . . . . . . Windshield, washing . . . . . . . .
File:17rcgsc.
