Contents Before driving Introduction 2 Instrumentation 4 Controls and features 20 Seating and safety restraints 89 Starting and driving Starting 120 Driving 127 Roadside emergencies 150 Servicing Maintenance and care 171 Capacities and specifications 230 Customer assistance 236 Reporting safety defects (U. S.
Introduction ICONS Indicates a safety alert. Read the following section on Indicates that vehicle information related to recycling and other environmental concerns will follow. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps towards protecting the environment. WARNINGS Provide information which may reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment.
Introduction If possible, you should avoid full use of the brakes for the first 1 600 km (1 000 miles). INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation.
Instrumentation Page 20, 21 Headlamp control/ Foglamp control* Page 70 Turn signal/ high beams Page 69 Hazard flasher control Page 21 Panel dimmer control Page 6 Instrument cluster Page 71 Windshield wiper/washer control Page 80 Luggage compartment release Page 175 Hood release 4 Page 69 Tilt steering wheel lever Page 68 Ignition switch Page 72 Speed control * Page 100 Air bag system
Instrumentation Page 22 Trip computer Page 86 AntiĆtheft system status indicator On various models the appearance and location of some items may differ from those shown here. However, the page references given still apply.
Instrumentation INSTRUMENT CLUSTER LIGHTS AND CHIMES Check engine Your vehicle is equipped with a computer that monitors the engine's emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD II system also assists the service technician in properly servicing your vehicle.
Instrumentation The check engine" indicator light illuminates when the ignition is first turned to the position to check the bulb. If it comes on after the engine is started, one of the engine's emission control systems may be malfunctioning. The light may illuminate without a driveability concern being noted. The vehicle will usually be drivable and will not require towing.
Instrumentation If the check engine" light remains on, have your vehicle serviced at the first available opportunity. Engine misfire is occurring which could damage your catalytic converter. You should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity.
Instrumentation Air bag readiness Foglamps Foglamp control Controls and features Turn signals
Instrumentation High beams Traction control system (if equipped) Safety belt Saf
Instrumentation Charging system Illuminates when the ignition is turned on and the engine is off. The light also illuminates when the battery is not charging properly and the vehicle may require electrical system service. Engine oil pressure Illuminates when the ignition is turned on and the engine is off. The light also illuminates when engine oil pressure falls below the normal range. Refer to the Maintenance and care chapter to check the engine oil level as soon as possible.
Instrumentation Low coolant (if equipped) Maintenance and care Anti-lock brake system (ABS) (if equipped)
Instrumentation O/D off indicator (automatic transaxle only) Automatic transaxle warning (if equipped)
Instrumentation Testing the warning and indicator lights Turn the ignition key to the on position without starting the engine. The following warning and indicator lights should illuminate: charging system, safety belt (does not illuminate, if the driver's safety belt is fastened), low coolant, engine oil pressure, check engine, air bag readiness, traction control, brake system and ABS. The overhead warning lights (if equipped) should also illuminate briefly.
Instrumentation Headlamps on warning chime Sounds when the headlamps are on, the ignition is off (and the key is not in the ignition) and the driver's door is open. Key-in-ignition warning chime Sounds when the key is left in the off/lock or accessory position and the driver's door is open. Safety belt warning chime For information on the safety belt warning chime, refer to the Seating and safety restraints chapter.
Instrumentation INSTRUMENT CLUSTER GAUGES Engine coolant temperature gauge Engine coolant maintenance Maintenance and care
Instrumentation Tachometer Indicates the engine speed in revolutions per minute (rpm). Trip odometer Registers the distance traveled on individual journeys. Refer to Trip computer in the Controls and features chapter. Speedometer Indicates the current vehicle speed. Speedometer Odometer Registers the total distance traveled by the vehicle. Odometer Fuel gauge Displays the approximate level of usable fuel left in the fuel tank. The light in the gauge illuminates when the fuel level is low.
Instrumentation OVERHEAD WARNING LIGHTS (if equipped) These lights illuminate briefly when the ignition key is turned to the on position. Service intervals Illuminates after approximately 7 700 km (4 800 miles) or 358 days to indicate that routine service should be performed. Check your maintenance schedule to determine the routine service to be completed. Routine service should be performed by an authorized Ford or Lincoln/Mercury Dealer.
Instrumentation Danger of ice warning Illuminates when 0ºC (32ºF) and below. The red sign warns of an increased danger of icy roads. The absence of a light in cold temperatures does not necessarily mean that there is no risk of ice on the road. Caution should be exercised when weather conditions indicate that ice may be present. Even if the air temperature rises to above +4_C (39_F) it is no guarantee that the road is free of ice.
Controls and features INSTRUMENT PANEL CONTROLS Headlamp control
Controls and features Foglamp control (if equipped) Pull the control toward you while the headlamps are on to turn the foglamps on. Push the control in to turn off the foglamps. Daytime running lights (DRL) (Canadian vehicles only) The DRL system turns the headlamps on, with a reduced light output, when: • the ignition is in the on position and • the headlamp is in the off position. Always remember to turn on your headlamps at dusk or during inclement weather.
Controls and features Trip computer !! " #"" " "% " "# $ ! " " !" " "& # !# " !! " #"" " " "% ! " # "! !! " #"" " ! " " # " " ' ! " Temperature %! " #"! " "# Average speed %! " $ ! ! !" ! "
Controls and features Tripmeter Shows how far you have traveled since last reset. Distance to empty Shows the approximate distance you can drive with the fuel remaining in the tank. Average fuel economy Shows the average fuel economy since last reset. Digital clock Switch the ignition on: The clock can be set to either 12 or 24 hour format. To toggle between 12 or 24 hour format, depress the CLOCK button. Then press the UNITS button until HR" is in the display.
Controls and features Traction control system (if equipped) ! ! ! ! Traction Control Driving Rear window defroster
Controls and features Climate controls Your vehicle has one of the following climate control systems: • Manual heating system • Manual heating and air conditioning system In some modes, the two systems function similarly. In modes where the systems do not function similarly, the different functions are noted. Vents Adjust as necessary. Low airflow: rotate vent clockwise. High airflow: rotate vent counterclockwise.
Controls and features Temperature Controls the temperature of the airflow inside the vehicle. Fan speed Controls the volume of air circulated in the vehicle. Mode selector Controls the direction of the airflow to the inside of the vehicle. The air conditioning compressor (if equipped) will operate in all modes except , , and . However, the air conditioning will only function if the outside temperature is 4°C (39°F) or above.
Controls and features • MAX A/C (if equipped): Uses recirculated air to cool the vehicle. Air will flow from the instrument panel registers. Use this mode to prevent any undesirable odors from entering the vehicle. • A/C (if equipped): Uses outside air to cool the vehicle. Air will flow from the instrument panel registers. • : Distributes outside air through the instrument panel registers.
Controls and features : Allows for maximum heating • by distributing outside air through the floor ducts. If temperature is set to cool, the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode. • ā: Distributes outside air through the windshield defroster ducts and the floor ducts. For added customer comfort, the air distributed through the floor ducts will be slightly warmer than the air sent to the windshield defroster ducts.
Controls and features • The outer vents can be used to defrost the side windows. This operates in all modes except defrost. To operate, the center vents must be closed and the outer vents positioned towards the windows. • Don't put objects under the front seat that will interfere with airflow to the back seats. • Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield). • When placing objects on top of your instrument panel, do not cover the defroster outlets.
Controls and features AUDIO SYSTEM Anti-theft protection panel
Controls and features Replacement panels Your dealer will require the following if you need to order a replacement panel: 1. Your name and address. 2. The Vehicle Identification Number (visible on a plate mounted in the engine compartment). 3. The audio unit type (e.g., 4500, 4600). 4. Proof of identification (e.g., driver's license, identity card). 5.
Controls and features Radio reception " !" " % &! "# " " !" !" !" " ! $ % " ! % & # " !" " & # # !&!" AM reception !" " ! !" ! ! $ !" ! # # "& "" ! !"# % $ " " " ! " ! & ! " ! " " " !" " ! FM reception % $ ! # "& ! # !"! #" ! !" " !# " "
Controls and features 4500 AND 4600 AUDIO CONTROLS The 4500 radio/cassette is compatible with a CD changer.
Controls and features The 4600 radio/CD player is compatible with a CD changer.
Controls and features On/off (ON/OFF) " $## " ! # # $ # ! $ # $! & # # # #$! ! $# # ' "& # " # ! $! Volume control (VOLUME) ! "" # " ' # " # % " # " Audio distortion reduction (CLIP).
Controls and features Fade control (FADE) Press FADE, then use the VOLUME control for fade (front and rear) adjustment. FADE" and the level selected appear in the display. Balance control (BALANCE) Press BALANCE, then use the VOLUME control for balance (left and right) adjustment. BAL" and the level selected appear in the display. Seek tuning control (SEEK) During radio reception, press or to locate the next station down or up the waveband selected.
Controls and features AutoStore selector AutoStore selects six strong FM station signals and stores them on the preset buttons. • Press and hold the AM/FM button to activate AutoStore. • AST" flashes in the display while the unit searches through the FM frequencies. • When the search is complete, sound is restored on preset button 1. • Other stored stations can be selected using the other preset buttons.
Controls and features Stereo indicator The symbol shows whenever a stereo signal is received. CD changer Refer to the section 2060/2062 CD changer. MENU button (main features) – radio Use the MENU button to access main menu features and the SEEK button for adjustment. Manual tuning Press the MENU button once then use the SEEK button to make manual tuning adjustments. The FM waveband allows 200 kHz tuning steps, and the AM band 10 kHz steps.
Controls and features Scan tuning Press the MENU button twice then use the SEEK button to start a scan. The radio tunes to and plays the next station on the waveband. After a short period it tunes to and plays the next station. During this scan, Scn" appears in the display. If you wish to continue listening to a station tuned to, press SEEK or MENU. Pressing SEEK or MENU at any time will end the scan. VID LOCK appears in the radio display; this message should be disregarded.
Controls and features Automatic Volume Control Press the MENU button three times then use the SEEK button to turn this function on (AVC +1" to AVC +7") or off (AVC OFF"). • When selected, Automatic Volume Control increases or decreases the audio unit's volume level to compensate for engine and road speed noise. • The SEEK button provides a selection of settings between AVC OFF" and AVC +7". The display shows the level selected.
Controls and features Audio distortion reduction (CLIP) Press and hold the MENU button then press it again and use the SEEK button to turn this function on (CLIPĆON") or off (CLIPĆOFF"). With the CLIP" feature activated, the audio unit automatically detects sound distortion and reduces the unit's volume level until the distortion has been eliminated. This means that while the display might change numerically, there may be no increase in sound.
Controls and features Fast forward/rewind • For fast forward, press the button when the display arrow if it points to the right, or points to the left. • For rewind, press the button when the display arrow points to if it points to the the left, or right. • To restart tape playback during fast forward or rewind partially, press and release the other tape control button. During fast forward and rewind, radio reception is automatically restored (with Automatic Music Search function turned off).
Controls and features To pause tape playback Press AM/FM to pause tape playback and restore radio reception, or the CD button for CD playback. Tape eject Press both and buttons fully in to eject the cassette and restore radio reception. Cassette care and maintenance For best possible sound quality, use tape cassettes that are clean and in good condition.
Controls and features Automatic Music Search (AMS) Press the MENU button once then use the SEEK button to turn this function on (AMSĆON") or off (AMSĆOFF"). With this feature on, press either the or button (as appropriate), to obtain the previous or next track on the tape. Dolby BR noise reduction Press the MENU button twice then use the SEEK button to turn this function on (DOLBY NR ON") or off (DOLBY NR OFF"). With the function on, background tape noise is reduced.
Controls and features Automatic Volume Control Press the MENU button three times then use the SEEK button to turn this function on ("AVC ON") or off ("AVC OFF"). • When selected, Automatic Volume Control increases or decreases the audio unit's volume level to compensate for engine and road speed noise. • The SEEK button provides a selection of settings between AVC OFF" and AVC +7". The display shows the level selected. This feature is not available on some vehicles and will not appear as a menu function.
Controls and features 4600 units only CD Playback (8 cm and 12 cm CDs can be played) CD playback starts and radio reception is interrupted, when a CD is inserted into the entry slot. CD PLAY" appears in the display. Press CD/EJ to start playback from a CD already in the audio unit. If no disc is inserted, NO DISC" appears in the display. The display indicates elapsed track time up to 19:59.
Controls and features Fast forward/reverse Press and hold SEEK or SEEK to search backwards or forwards across the tracks on the disc. To end CD playback Press the AM/FM button to restore radio reception without ejecting the disc. If reselected, the CD will start from wherever playback was last interrupted. CD eject • During CD playback, press CD/EJ once. • During radio reception, press CD/EJ twice. When ejected, the disc is held ready for removal.
Controls and features CD error codes Codes may be shown in the audio unit display that indicate errors with the CD unit. These codes are as follows: Display E11 or E15 Description/rectification Internal fault, see your dealer. E12 Clean the disc and try again. If error still shows, see your dealer. E14 Ambient temperature too hot - unit will not work until it has cooled down. E16 There is an eject fault, see your dealer. CD Changer Refer to the section 2060/2062 CD changer.
Controls and features Random track playback (SHUF) Press the MENU button once then use the SEEK button to turn this function on (SHUFĆON") or off (SHUFĆOFF"). With the function on, the elapsed time indicator is replaced by SHUF" as a new track is selected. If an optional CD changer is fitted, the audio unit plays all the tracks on the disc selected, then moves onto the next disc in the CD magazine and plays the tracks on that disk in random sequence.
Controls and features Automatic Volume Control Press the MENU button three times then use the SEEK button to turn this function on (AVC ON") or off (AVC OFF"). • When selected, Automatic Volume Control increases or decreases the audio unit's volume level to compensate for engine and road speed noise. • The SEEK button provides a selection of settings between AVC OFF" and AVC +7". The display shows the level selected. This feature is not available on some vehicles and may not appear as a menu function.
Controls and features 4700 AUDIO CONTROLS The 4700 radio/cassette is compatible with a CD changer.
Controls and features On/off power and volume control (VOL ON/OFF) • Press for on/off. The control can also operate the unit for up to one hour with the ignition turned off. The radio automatically switches off after one hour. • Rotate the control and the display indicates the volume level selected. See also Audio distortion reduction (CLIP). Bass/treble control (BASS/TREB) Press once for bass or twice for treble and use the volume control for adjustment. The display indicates the level selected.
Controls and features Seek tuning control (SEEK) During radio reception, press or to locate the next station down or up the waveband selected. Waveband selector (AM/FM) • Press AM/FM during tape or CD playback to restore radio reception. • Press repeatedly during radio reception to select AM, FM1, FM2 and AutoStore bands. The display indicates the selection made. AutoStore selector AutoStore selects six strong FM station signals and stores them on the preset buttons.
Controls and features Automatic Volume Control (AVC) When selected, Automatic Volume Control increases or decreases the audio unit's volume level to compensate for engine and road speed noise. The SEEK button provides a selection of settings between AVC OFF" and AVC +7". The display shows the level selected. This feature is not available on some vehicles. Station preset buttons Select a waveband (FM or AM) and tune to the station required. Press and hold one of the preset buttons.
Controls and features Tape controls • !& %' ! ' # ") %% & % " "% # + ! &' %'& ' # # + • , , ! , "% , '" & "* * & & # + ! ## % ! ' &# + • % && ' (''"! (% ! # + '" ! ' ' # & ' ' & # + ! • (% ! % " % #' "! "% # + #% && ' (''"! '" &' %' ' # # + • & #% && * ! && '' & !"' !& %' , ## %& ! ' &# + Automatic Music Search (AMS) ' , (& !
Controls and features Fast forward/rewind Press SEEK twice for fast forward or SEEK twice for fast rewind. TAPE FWD" (tape forward) or TAPE RWD" (tape rewind) appear in the display. Press either side of the SEEK control to end fast forward or rewind and to restore tape playback. During fast forward and rewind, radio reception is restored. To pause tape playback Press the CD button to start CD playback or AM/FM to restore radio reception.
Controls and features Cassette care and maintenance For best possible sound quality, use tape cassettes that are clean and in good condition. It is also recommended that the tape head in the audio unit is cleaned regularly with a wet cleaning cassette, which is available from your dealer. CD Changer Refer to the section 2060/2062 CD changer. Track compression (COMP) Refer to the section 2060/2062 CD changer. Random track playback (SHUF) Refer to the section 2060/2062 CD changer.
Controls and features Scan tuning Press the MENU button twice then use the SEEK button to start a scan. The radio tunes to and plays the next station on the waveband. After a short period, it tunes to and plays the next station. During this scan, SCAN" appears in the display. If you wish to continue listening to a station tuned to, press SEEK or MENU. Pressing SEEK or MENU at any time will end the scan.
Controls and features 2060/2062 CD CHANGER CD changer location The CD changer is located in the luggage compartment. Loading the disc magazine The CD changer magazine takes up to six discs, numbered 1 to 6 starting from the bottom. To load a disc: • Slide open the CD changer unit door, press the eject button and remove the magazine. • Insert individual discs label side up into each slot until they click into a held position. • Do not insert more than one disc into each position.
Controls and features To eject a disc Pull forward the lever on the side of the magazine, which corresponds with the disc to be ejected. The disc will move forward ready for removal. To insert the magazine An arrow on the magazine shows how to reinsert it into the CD changer. The magazine clicks into position ready for use. Keep the disc changer door closed at all times, except when inserting the magazine.
Controls and features OPERATING A CD CHANGER 4500 and 4700 units Press the CD button. CD" appears in the display along with a flashing number to indicate the disc selected. Playback overrides radio or tape playback. During normal operation, CDs and tracks are automatically selected and played sequentially in ascending order. Disc one follows disc six. The display indicates elapsed track time up to 19:59.
Controls and features Without a CD in the 4600 unit ! ! ! Disc selection " & ! ! "!! ! ! & ! Track selection ! !" ! ! ! ! ! ! & $ ! ! ! ! ! ! ! # " ! $ ! ! ! ! %! ! ! $ $ & ! ! ! ! Fast forward/reverse
Controls and features To pause CD changer playback 4500 units Press the AM/FM button to restore radio reception, or push the cassette controls partially in for tape playback. 4600 units • Press AM/FM to pause CD playback and restore radio reception. • Press CD/EJ to play a single disc inserted into the audio unit. 4700 units • Press the AM/FM button to restore radio reception. • Press TAPE for tape playback. To resume CD changer playback, press the changer control button.
Controls and features Disc/magazine missing • If the CD changer is selected but is not fitted, radio or tape playback will continue uninterrupted. NO CD" or NO CD DETECTED" on 4700 units appears in the display. • If a changer is fitted, but the magazine is missing or incorrectly inserted, when CD or CD/EJ is pressed radio reception is resumed. NO DISCS" or MAGAZINE EJECTED" on 4700 units appears in the display.
Controls and features CD error codes Codes may be shown in the audio unit display that indicate errors with the CD unit. These codes are as follows: Display Description/rectification CD ERROR or Internal fault, see your dealer. E5 E2 or E3 E4 Clean the disc and try again. If error still shows, see your dealer. Ambient temperature too hot - unit will not work until it has cooled down. MENU button (main features) – CD Use the MENU button to access main menu features, and the SEEK button for adjustment.
Controls and features Random track playback (SHUF) 4500 and 4600 units Press the MENU button once then use the SEEK button to turn this function on (SHUFĆON") or off (SHUFĆOFF"). With the function on, the elapsed time indicator is replaced by SHUF" as a new track is selected. If an optional CD changer is fitted, the audio unit plays all the tracks on the disc selected then moves onto the next disc in the CD magazine and plays the tracks on that in random sequence.
Controls and features 4700 units Track compression (COMP) is not a menu feature, it is selected by using the COMP button to turn the function on (COMPĆON") or off (COMPĆOFF"). Automatic Volume Control (AVC) 4500 and 4600 units Press the MENU button three times then use the SEEK button to turn this function on (AVC ON") or off (AVC OFF"). • When selected, Automatic Volume Control increases or decreases the audio unit's volume level to compensate for engine and road speed noise.
Controls and features STEERING COLUMN CONTROLS Ignition 1. Ignition off, steering wheel locked. On vehicles with automatic transaxles, the ignition key can return to this position only if the gearshift lever is in P (Park). 2. The accessory position. Steering unlocked, radio operational. Ignition and all main electrical circuits are disabled. The ignition key should not be left in this position for too long to avoid discharging the battery unnecessarily.
Controls and features 3. Ignition switched on, all electrical circuits operational. Warning and indicator lights illuminate. This key position is for normal driving. 4. Starter motor activated. Release the key as soon as the engine starts. Tilt steering Pull the locking lever on the steering column cover up to adjust the steering column position. Secure the wheel by releasing the locking lever. Never adjust the steering wheel while the vehicle is moving.
Controls and features Multi-function switch Right turn signal Left turn signal Flash-to-pass ! ! High beam headlamps
Controls and features Windshield wipers and washer Wipers Lift the windshield wiper lever to the desired speed interval. • Intermittent: push lever up to the first position. • Low: push lever up to the second position. • High: push lever up to the third position. For a single wipe, push the lever downward. Intermittent wiper control Rotate the variable intermittent wiper control to the desired speed. 1 = Short time interval 6 = Extended time interval Washer Pull the lever toward the steering wheel.
Controls and features Speed control (if equipped) Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. To turn speed control on • Press On. Vehicle speed cannot be controlled until the vehicle is travelling at or above 48 km/h (30 mph). Do not shift the gearshift lever into N (Neutral) with the speed control on.
Controls and features To turn speed control off • Press Off or • turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. To set a speed Press +. For speed control to operate, the speed control must be on and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal.
Controls and features To set a higher speed • Press and hold +. Release when the desired set speed is reached, or • press and release +. Each press will increase the set speed by 1.6 km/h (1 mph) or • accelerate with your accelerator pedal, then press +. You may accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle speed to the previously set speed. To set a lower speed • Press and hold -.
Controls and features To disengage speed control • Lightly depress the brake or clutch pedal. Disengaging the speed control will not erase the previously programmed set speed. To return to a set speed • Press =. For = to operate, the vehicle speed must be faster than 48 km/h (30 mph).
Controls and features OVERHEAD CONTROLS Interior lamps The interior lamps have three switch positions: door delay, off and on. When the control is switched to door delay (12 SEC), the interior light stays on for 12 seconds after the doors are closed with the ignition off. Door delay Off On Reading lamps (if equipped) The reading lamps are operated by separate on/off switches and can be adjusted to point in the desired direction.
Controls and features DOOR MOUNTED CONTROLS Power mirrors ! Breakaway mirrors ! !
Controls and features One touch down The driver's door can be lowered automatically. Momentarily press the down button. The driver's window will open fully. Press the up button to interrupt one touch operation. Power door locks Push to lock or unlock both doors. FLOOR MOUNTED CONTROLS Parking brake For information on the parking brake, refer to Preparing to start the vehicle in the Starting chapter. Cup holder To open, pull the cup holder upwards to the stop position.
Controls and features Positive retention floor mat (Driver’s side only) Position the floor mat in the footwell. Place the mat eyelet over the pointed end of the retention post from the rear and rotate forward to install. Adjust the floor mat position to allow proper operation of accelerator pedal, brake pedal and clutch pedal (if equipped). To remove, lift the floor mat just forward of the retention post and rotate it rearward to disengage it from the retention post.
Controls and features LUGGAGE COMPARTMENT Remote luggage compartment control " Closing the liftgate " ! "
Controls and features Cargo cover Removing the cargo cover Replacing the cargo cover
Controls and features REMOTE KEYLESS ENTRY SYSTEM (if equipped) Locking the doors
Controls and features Opening the luggage compartment Sounding the panic alarm ! ! Replacing the battery ! # ! # ! ! • ! •
Controls and features To replace the battery: 1. Twist a thin coin between the two halves of the transmitter. Do not take the front part of the transmitter apart. 2. Remove the old battery. 3. Place the positive (+) side of the new battery down. 4. Snap the two halves of the transmitter back together. Replacing lost transmitters Take your transmitters to the dealer for reprogramming if: • a transmitter is lost or • you want to purchase additional transmitters.
Controls and features ANTI-THEFT ALARM SYSTEM (if equipped) The system is available with Remote Keyless Entry. The system acts as a deterrent against unauthorized persons opening the doors, luggage compartment or hood. Activation The system is activated by pressing the control once. The ignition key must be removed from the ignition and the doors, hood and liftgate fully closed, to allow activation. The turn signal lamps will flash once to indicate the system is activated.
Controls and features PASSIVE ANTI-THEFT SYSTEM The Passive AntiĆTheft System (PATS) is an engine immobilization system. It is an additional theft protection feature which prevents the engine from being started unless a coded key is used. Automatic arming The system is armed five seconds after switching off the ignition. The armed status is indicated when the control light flashes every two seconds. The light is located on the dashboard above the climate controls.
Controls and features Functional check When the ignition is switched on, the control light will illuminate for approximately three seconds to indicate that the system is operating correctly. If the control light flashes rapidly for approximately one minute and then repeatedly at irregular intervals, the system did not recognize the key code. Remove the key and try again.
Controls and features Key coding A maximum of 7 keys in all can be coded with any two coded keys. • Insert the first key in the ignition switch and turn to position 3. • Turn the key back to position 1 and remove from the ignition switch within 5 seconds. • Insert the second key in the ignition switch and turn to position 3 within 5 seconds. • Turn the key back to position 1 and remove from the ignition switch within 5 seconds - the key coding mode is now activated.
Seating and safety restraints HEAD RESTRAINTS Adjusting the head restraints ! " ! SEATING Manually adjusting the seats
Seating and safety restraints Pull the lever on the outside of the seatback to lean the seatback forward. Fold back the seatback until it locks with a distinct `click' and slide the seat backwards until it locks in position. Rock the seat to ensure that the catch is securely engaged. Do not place any objects behind the seat which could prevent the engagement of the seat lock. Never adjust the driver's seat or seatback when the vehicle is moving.
Seating and safety restraints Seat (1) Forward and backward (2) Height of the entire seat Seatback (3) Seatback inclination Lumbar support (4) Lumbar support Closing the liftgate To avoid injury to rear seat occupants when closing the liftgate, ensure that the head of any rear seat occupant is not in the path of the closing liftgate. Request that the occupants, especially taller occupants, lean forward and under the roof structure to avoid making contact with the closing liftgate.
Seating and safety restraints SAFETY RESTRAINTS Important safety restraints precautions # % " # % ! ! ! # " ! % ! # % % ! " ! " ! # % % # % " # " $ % ! ! "
Seating and safety restraints This vehicle has a seat belt system with an energy management feature at the front seating positions to help further reduce the risk of injury in the event of a headĆon collision. This seat belt system has a retractor assembly that is designed to pay out webbing in a controlled manner. This feature is designed to help reduce the belt force acting on the occupant's chest.
Seating and safety restraints BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the seat belt assembly TellĆTale Label" (if applicable, located on lap portion at outboard side of seat above anchorage point) is activated and states that the retractor assembly is required to be replaced, or the seat belt assembly automatic locking retractor" feature or any other seat belt function is not operating properly when checked according to the procedures in the Service Manual.
Seating and safety restraints Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1. Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2. Never swing the safety belt around your neck over the inside shoulder. 3. Never use a single belt for more than one person.
Seating and safety restraints When to use the automatic locking mode • When a tight lap and shoulder belt fit is desired. • a child safety seat is installed in the vehicle. For information on the proper use of a child safety seat, refer to Safety seats for children later in this chapter. Using automatic locking mode The automatic locking mode must be used when installing a child safety seat in any passenger seat. 1.
Seating and safety restraints Front seat safety belt height adjustment # # # ! # " ! " " "
Seating and safety restraints Conditions of operation If... Then... If the driver's safety belt is not buckled before the ignition key is turned to on... The safety belt warning light illuminates for one to two minutes and the warning chime sounds for four to eight seconds. The driver's safety belt is buckled while the indicator light is illuminated and the reminder chime is sounding... The safety belt warning light and warning chime turn off.
Seating and safety restraints Safety belt maintenance " " " " ! " " ! " " " ! "
Seating and safety restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is the greatest close to the trim covering and the air bag module.
Seating and safety restraints All occupants of the vehicle including the driver should always properly wear their safety belts even when an air bag SRS is provided. Always transport children 12 years old and under in the back seat and always use appropriate child restraints. NHTSA recommends a minimum distance of at least ten (10) inches between an occupant's chest and the air bag module.
Seating and safety restraints Children and air bags ! ! ! ! ! ! ! "
Seating and safety restraints How does the front air bag system work? The air bag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration to cause the sensors to close an electrical circuit that initiates air bag inflation. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation.
Seating and safety restraints While the system is designed to help reduce serious injuries, it may also cause minor burns, abrasions, swelling or temporary hearing loss. Because air bags must inflate rapidly and with considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of air bag deployment.
Seating and safety restraints The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors. Determining if the system is operational The SRS uses a readiness light in the instrument cluster to indicate the condition of the system. Refer to the Air bag readiness section in the Instrumentation chapter.
Seating and safety restraints Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personal. Side air bag system (if equipped) Do not use accessory seat covers. The use of accessory seat covers may prevent the deployment of the side air bags and increase the risk of injury in an accident.
Seating and safety restraints Do not attempt to service, repair, or modify the air bag Supplemental Restraint System or its fuses. See your Ford or LincolnĆMercury dealer. All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS is provided. How does the side air bag system work? Side air bags, in combination with seat belts, can help reduce the risk of severe injuries in the event of a significant side impact collision.
Seating and safety restraints Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician in accordance with the vehicle service manual. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Seating and safety restraints Determining if the system is operational The SRS uses a readiness light in the instrument cluster to indicate the condition of the system. Refer to the Air bag readiness section in the Instrumentation chapter. Routine maintenance of the air bag is not required. A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit. • The readiness light will not illuminate immediately after the ignition is turned on.
Seating and safety restraints CHILDREN AND SAFETY RESTRAINTS Rear-facing child seats or infant carriers should never be placed in the front seats. To prevent the risk of injury, make sure children sit where they can be properly restrained. Whenever possible, put children in one of the rear seats of your vehicle. Accident statistics indicate that children are safer when properly restrained in the rear seats than in the front seats. Do not leave children, unreliable adults, or pets unattended in your vehicle.
Seating and safety restraints Important child restraint precautions You are required by law to use safety restraints for children in the U.S. and Canada. If small children ride in your vehicle (generally children who are four years old or younger and who weigh 18 kg [40 lbs] or less), you must put them in safety seats made especially for children. Check your local and state or provincial laws for specific requirements regarding the safety of children in your vehicle.
Seating and safety restraints Children and safety belts Children who are too large for child safety seats (as specified by the child safety seat manufacturer) should always wear safety belts. Follow all the important safety restraints and air bag precautions that apply to adult passengers in your vehicle. If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child's face or neck, the child should wear the lap and shoulder belt.
Seating and safety restraints SAFETY SEATS FOR CHILDREN RearĆfacing child seats or infant carriers should never be placed in the front seats. Carefully follow all of the manufacturer's instructions included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision. Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child.
Seating and safety restraints • Put the safety belt in the automatic locking mode. Refer to Using automatic locking mode in this chapter. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps see Attaching safety seats with tether straps in this chapter. Installing child safety seats in combination lap and shoulder belt seat positions 1.
Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer's instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle for that seating position until you hear and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5.
Seating and safety restraints 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in place. 10.
Seating and safety restraints Attaching safety seats with tether straps Top tether straps hold a forwardĆ facing child safety seat more securely in a crash, and help to fit the child safety seat snugly into the vehicle seat. A child safety seat with a VĆshaped tether (attached to both upper corners of the child safety seat) may fit more snugly with the high rear seat backs in your vehicle.
Seating and safety restraints Tighten the anchor according to manufacturer's specifications. Otherwise, the safety seat may not be properly secured and the child may be injured in a sudden stop or collision. To install a tethered forwardĆfacing child safety seat in the rear seat, remove the cargo area cover and hook the top tether strap to the anchor in the trunk (please refer to Tether anchor hardware).
Seating and safety restraints Install the forwardĆfacing child safety seat snugly in the front passenger seat using the lap/shoulder belt by first buckling the front belt and then putting it into automatic locking mode (pull all of the stored belt out of the retractor to initiate automatic lockingĆ mode, then let the retractor wind up the slack).
Starting IMPORTANT SAFETY PRECAUTIONS A computer system controls the engine's idle revolutions per minute (rpm). When the engine starts, the idle rpm runs faster to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked by your dealer or a qualified service technician. Do not allow the vehicle to idle for more than ten minutes.
Starting Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. IMPORTANT VENTILATION INFORMATION If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (1 inch). Adjust the heating or air conditioning to bring in fresh air.
Starting Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris. Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes. These fumes are harmful and could kill you.
Starting PREPARING TO START THE VEHICLE Engine starting is controlled by the spark ignition system. This system meets all Canadian InterferenceĆ Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuelĆinjected engine, avoid pressing the accelerator pedal before or during starting. Only use the accelerator pedal when you have difficulty starting the engine.
Starting If starting a vehicle with an automatic transaxle: • Make sure the parking brake is set. • Make sure the gearshift is in P (Park). If starting a vehicle with a manual transaxle: • Make sure the parking brake is set. • Push the clutch pedal to the floor otherwise the engine will not crank (turn over). • Put the gearshift into neutral. 3. Turn the key to the on position (without turning the key to start).
Starting STARTING THE ENGINE 1. Turn the key to the start position (4) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to the on (3) position. 2. If the engine does not start within five seconds, wait ten seconds and try again. 3. If the engine does not start in two attempts OR the temperature is below -12ºC (10ºF), depress the accelerator pedal and start the engine while holding the accelerator pedal down.
Starting USING THE ENGINE BLOCK HEATER (IF EQUIPPED) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heaterĆdefroster system to respond quickly. It is strongly recommended if you live in a region where temperatures reach -23ºC (-10ºF) or below. For best results, plug the heater in at least three hours before starting the vehicle.
Driving BRAKES Your brakes are selfĆadjusting. Refer to the Scheduled Maintenance Guide" for maintenance intervals. Anti-lock braking system (ABS) (if equipped) On vehicles equipped with an antiĆlock braking system (ABS), a noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events.
Driving Operation of the anti-lock braking system The ABS operates by detecting the onset of wheel lock up during brake applications and compensating for this tendency. The wheels are prevented from locking even when the brakes are firmly applied. Braking with ABS • In an emergency, apply full force on the brake.
Driving Parking brake To engage the parking brake: Pull the handle upward. To release the parking brake: 1. Pull the handle up slightly. 2. Press and hold the release button. 3. Push handle downward to the off position. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transaxle) or in 1 (first) (manual transaxle). To prevent personal injury, do not release the parking brake while outside the vehicle.
Driving TRACTION CONTROL This system prevents wheel spin at all speeds. The control will toggle this function on and off, but the feature defaults to on after each cycle of the ignition key. The traction control system controls excessive wheel spin by automatically applying and releasing the brakes in conjunction with engine torque reductions. This can occur when accelerating on a slippery road, a loose surface or when pulling away on a hill.
Driving STEERING YOUR VEHICLE Your vehicle comes with power steering. Power steering uses energy from the engine to help steer your vehicle. If the amount of effort needed to steer your vehicle changes at a constant vehicle speed, have the power steering checked. If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually but it takes more effort. Never hold the steering wheel to the extreme right or left for more than five seconds if the engine is running.
Driving Overriding the brake-shift interlock feature If you cannot move the gearshift lever from P (Park) with the brake pedal depressed: 1. Turn the ignition off and remove the ignition key. 2. Apply the parking brake and the brake pedal. 3. Insert a screwdriver or similar item about 5 cm (2 inches) into the square opening to the right of the gearshift at the base of the console.
Driving The brakeĆshift interlock feature is designed to further enhance the safety of vehicle occupants when the vehicle is placed into gear. To preserve the benefits of this feature, have any repairs completed promptly. The consoleĆmounted gearshift will lock when you turn the key to the lock position. When the gearshift is in any position except P (Park), the ignition key cannot be turned to lock or removed from the steering column. To remove the key, the gearshift lever must be in P (Park).
Driving R (Reverse) With the gearshift in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear. D (Overdrive) The normal driving condition for the best fuel economy. Transaxle operates in gears one through four.
Driving Deactivate D (Overdrive) when: • driving with a heavy load. • towing a trailer up or down steep hills. • additional engine braking is desired. To return to D (Overdrive) mode, press the transaxle control switch. The O/D OFF message in the instrument cluster will extinguish. Every time the vehicle is shut off and restarted, you must press the transaxle control switch to cancel overdrive operation if driving in overdrive is not desired.
Driving Manual transaxle (if equipped) Vehicles equipped with a manual transaxle have a starter interlock that prevents cranking the engine unless the clutch pedal is fully depressed. Using the clutch When starting a vehicle with a manual transaxle: 1. Hold down the brake pedal. 2. Depress the clutch pedal. 3. Put the gearshift lever in neutral. 4. Start the vehicle. 5. Put the gearshift in 1 (First) or R (Reverse). 6. Release the clutch slowly while pressing gradually down on the accelerator pedal.
Driving Recommended shift speeds 2.0 litre engine 5-speed transaxle shift speed schedules Recommended upshifts: Shift from During acceleration: During cruise*: km/h mph km/h mph First to second 22 14 19 12 Second to third 40 25 32 20 Third to fourth 53 33 46 29 Fourth to fifth 77 48 64 40 2.
Driving Parking 1. Apply the brake and the clutch and shift into neutral. 2. Engage the parking brake. 3. Shift into 1 (First). 4. Turn the ignition off. Do not park your vehicle in neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake. Reverse To shift into R (Reverse): 1. Completely stop your vehicle. 2. Depress the clutch pedal to the floor and place the gearshift lever in the neutral position. Do not release the clutch pedal. 3.
Driving LOADING YOUR VEHICLE Before loading your vehicle, familiarize yourself with these terms. Base curb weight Weight of the vehicle including any standard equipment, fluids and lubricants. It does not include passengers or aftermarket equipment. Payload Combined maximum allowable weight of passengers, cargo and optional equipment. The payload equals the gross vehicle weight rating minus base curb weight. GVW (Gross Vehicle Weight) Base curb weight plus the payload weight.
Driving GVWR (Gross Vehicle Weight Rating) Maximum total weight of the base vehicle, passengers, optional equipment and cargo. The GVWR is specific to each vehicle and is listed on the Safety Compliance Certification Label on the driver's door pillar. GAWR (Gross Axle Weight Rating) Carrying capacity for each axle system (front and rear). The GAWR is specific to each vehicle and is listed on the Safety Compliance Certification Label on the driver's door pillar.
Driving Payload = GVWR minus Base curb weight To obtain the correct weight for your vehicle, take your vehicle to a shipping company or an inspection station for trucks. Do not use replacement tires with lower weight capacities than the originals because they might lower the vehicle's GVWR and GAWR. (Replacement tires with a higher weight limit than the originals do not increase the GVWR and GAWR limitations.
Driving It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly. Driving with a heavy load The total weight of the vehicle plus the total weight of passengers and cargo should never exceed the GVWR.
Driving TRAILER TOWING Your vehicle is capable of towing a trailer of up to a maximum of 454 kg (1 000 lbs) gross trailer weight with a maximum tongue load of 45 kg (100 lbs). It should also have 2.3 sq. meters (25 sq. feet) or less frontal area. Do not drive faster than 72 km/h (45 mph) while towing a 454 kg (1 000 lb) trailer. Your vehicle does not come from the factory fully equipped to tow. No towing packages are available through Ford or Lincoln/Mercury dealers.
Driving Follow these guidelines to ensure safe towing procedure: • Stay within your vehicle's load limits. • Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter. • Use extra caution when driving while trailer towing. Refer to Driving while towing a trailer in this chapter. • Service your vehicle more frequently if you tow a trailer. Refer to the severe duty schedule in the Scheduled Maintenance Guide".
Driving Do not exceed the maximum loads listed on the Safety Compliance Certification Label. For load specification terms found on the label, refer to Loading your vehicle in this chapter. Remember to figure in the tongue load of your loaded vehicle when figuring the total weight. Towing trailers beyond the maximum recommended gross trailer weight could result in engine damage, transaxle damage, structural damage, loss of control, and personal injury.
Driving Using a hitch Do not use hitches that: • Clamp onto the vehicle bumper. • Attach to the axle. Distribute the load so that only 10 to 15% of the total weight of the trailer is on the tongue. Tie down the load so that it does not shift and change weight on the hitch. Follow the instructions of a reputable rental agency. Using trailer lamps Trailer lamps may be required on towed vehicles. Make sure your trailer lamps conform to any applicable regulation.
Driving Using trailer brakes Use electric brakes or manual, automatic or surge type hydraulic brakes that meet federal and local regulations. Install and adjust brakes according to the manufacturer's instructions. Do not connect a trailer's hydraulic brake system directly to your vehicle's brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase. Using safety chains Always connect the trailer's safety chains to the vehicle.
Driving Driving while towing a trailer Do not drive faster than 72 km/h (45 mph) while towing a 454 kg (1 000 lb) trailer. Do not drive faster than 72 km/h (45 mph) with any weight trailer while towing in hilly terrain or on hot days. Speed control (if equipped) may not work properly while towing on long, steep grades. If driving with an automatic transaxle: • Use D (Drive) or a low gear rather than D (Overdrive) while towing up or down steep inclines. • Anticipate stops and brake gradually.
Driving FUEL CONSUMPTION • • • • • • • • • • •
Roadside emergencies HAZARD FLASHER CONTROL Use only in an emergency to warn traffic of vehicle breakdown or approaching danger. Depress to activate. Depress again to switch off. The hazard lights can be operated when the ignition is off. FUEL PUMP SHUT-OFF SWITCH If the engine cranks, but does not start or does not start after a collision, the fuel pump shutĆoff switch may have been activated.
Roadside emergencies If you see or smell fuel, do not reset the switch or try to start your vehicle. Have all the passengers get out of the vehicle and call the local fire department or a towing service. If your engine cranks but does not start after a collision or substantial jolt: 1. Turn the ignition key to the off position. 2. Check under the vehicle for leaking fuel. 3. If you do not see or smell fuel, push the red reset button down.
Roadside emergencies FUSES AND RELAYS If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire. Check the appropriate fuses before replacing any electrical components. Always replace a fuse with one that has the specified amperage rating. Using a fuse with higher amperage rating can cause severe wire damage and could start a fire.
Roadside emergencies Power distribution box To check or replace a fuse or a relay, remove the cover of the fuse box in the engine compartment by releasing the latch (1) and lifting up. A blown fuse can be identified by a break in the wire. All fuses are a push fit. Reserve fuses with different ampere ratings are located in the power distribution box. 1 Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Roadside emergencies Fuses in the power distribution box (engine compartment) Fuse Ampere rating Color Description 1 2 3 4 5 6 7 8 9 10 11 7.5 20 3 20 15 20 brown yellow violet yellow blue yellow 12 13 14 15 16 17 18 39 40* 41* 42 43 44 45* 20 7.5 7.5 7.5 7.
Roadside emergencies Relays in the power distribution box (engine compartment) Relay Color R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 D1 D2 black black black black black black green black dark green green black black Description Fuel pump Engine management Air conditioning Low beam High beam Horn Starter High speed engine cooling fan Engine cooling fan Not used Daytime running lights (Canada only) Reverse voltage protection Air conditioning Passenger compartment fuse panel To check or replace a fuse or a relay
Roadside emergencies A blown fuse can be identified by a break in the wire. All fuses are a push fit.
Roadside emergencies Passenger compartment fuse panel (below instrument panel) Fuse Ampere rating Color 19 20* 21 22 23 7.5 10 40 7.5 15 brown black orange brown blue 24 25 26 27 28 29 30 15 20 7.5 15 30 30 7.5 blue yellow brown blue green green brown 31 7.5 brown 32 33 34 35 36 37 38 7.5 7.5 7.5 15 30 7.
Roadside emergencies CHANGING TIRES Park your vehicle in such a position where neither the traffic nor you are hindered or endangered when changing the tire. Ensure that the vehicle is on firm, level ground. Secure your vehicle further by blocking the wheels. Activate the hazard lights. Apply the parking brake and engage first or reverse gear or, if the vehicle has an automatic transaxle, select the P (Park) position. If parking on a slope is unavoidable, block the wheels.
Roadside emergencies The temporary spare tire The vehicle may have a high pressure temporary spare tire. This spare is smaller than a regular tire and is designed for emergency use only. This tire should be replaced as soon as possible. If you use the temporary spare tire continuously or do not follow these precautions, the tire could fail, causing you to lose control of the vehicle, possibly injuring yourself or others.
Roadside emergencies Spare tire location The spare tire and tools are located under the floor cover in the luggage compartment. Removing the spare tire and tools 1. Raise the rear of the floor cover in the luggage compartment and fold it forward. 2. Completely unscrew the bolt. 3. Lift out the spare wheel. 4. Remove the jack which is located beneath the spare tire.
Roadside emergencies Tire changing procedure Removing a tire 1. Apply the parking brake and 1 (First) gear (manual transaxle) or the P (Park) position (automatic transaxle). 2. Activate the hazard flashers. 3. The driver and all passengers must leave the vehicle. 4. Secure the vehicle against rolling or sliding. 5. Insert the tapered end of the jack handle beneath the hub cover (if fitted) and push in. Twist off to remove the cover. 6. Loosen the wheel nuts slightly. 7.
Roadside emergencies Replacing a tire 1. Push the spare tire onto the wheel studs. 2. Screw on the wheel nuts, ensuring the tapered end of the wheel nuts are facing the wheel, and secure in a clockwise direction. 3. Lower the vehicle and remove the jack by turning the handle counterclockwise. 4. Fully tighten the wheel nuts in a crosswise pattern. 5. Align the hub cover and push firmly into position with the ball of the hand. 6.
Roadside emergencies JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalytic converter. Batteries contain sulfuric acid which burns skin, eyes, and clothing, if contacted. Do not attempt to push start your vehicle. Automatic transaxles do not have pushĆstart capability. Preparing your vehicle 1.
Roadside emergencies 3. Park the booster vehicle close to the hood of the disabled vehicle, making sure the two vehicles touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect from any electrical surges. Turn all other accessories off.
Roadside emergencies 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle's engine, away from the battery and the carburetor.
Roadside emergencies Do not connect the end of the second cable to the negative (-) terminal of the battery to be jump. A spark may cause an explosion of the gases that surround the battery. • 2.0 litre engine • 2.
Roadside emergencies 5. Be sure that the cables are clear of fan blades, belts and other moving parts of both engines. Jump starting 1. Start the engine of the booster vehicle and run the engine at a moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for a further three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1.
Roadside emergencies 2. Remove the jumper cable on the negative (-) connection of the booster vehicle's battery. 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle's battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle's battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn" its idle conditions.
Roadside emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. Recommended towing options include wheel lift towing or flat bed towing. When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Company for all authorized tow truck operators.
Roadside emergencies TOWING YOUR VEHICLE BEHIND ANOTHER VEHICLE At times you may want to tow your vehicle behind another vehicle. Before you have your vehicle towed: • Release the parking brake. • Move the gearshift to N (Neutral). • Turn the key in the ignition to off. • Unlock the steering wheel. Automatic transaxle Do not tow your vehicle at a speed faster than 55 km/h (35 mph) or for a distance greater than 80 km (50 miles), unless the drive wheels are placed on dollies.
Maintenance and care SERVICE RECOMMENDATIONS • We highlight doĆitĆyourself items in the engine compartment for easy location. • As possible, we design parts that can be replaced without tools. • We provide you with a Scheduled Maintenance Guide" which makes tracking routine service for your vehicle easy. If your vehicle requires professional service, your Ford or Lincoln/Mercury dealership can provide necessary parts and service. Check your Warranty Guide to find out which parts and services are covered.
Maintenance and care Precautions when servicing your vehicle Be especially careful when inspecting or servicing your vehicle. Here are some general precautions for your safety: • Do not work on a hot engine. The cooling fan is automatic and may come on at any time. Always disconnect the negative terminal of the battery before working near the fan. • If you must work with the engine running, avoid wearing loose clothing or jewelry that could get caught in moving parts. Take precautions with long hair.
Maintenance and care Working with engine off (automatic transaxle) 1. Set the parking brake fully and ensure the gearshift is securely latched in P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly. Working with engine off (manual transaxle) 1. Set the parking brake, depress the clutch and place the gearshift in 1 (First) or R (Reverse). 2. Turn off the engine and remove the key. 3.
Maintenance and care Working with engine on (automatic transaxle) 1. Set the parking brake fully and ensure the gearshift is securely latched in P (Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly. Do not start your engine with the air cleaner removed and do not remove it while the engine is running. Working with engine on (manual transaxle) 1. Set the parking brake, depress the clutch and place the gearshift in neutral. 2.
Maintenance and care Opening the hood • Pull the handle (1) located under the instrument panel. • Release the safety catch by reaching under the hood (2) and pushing it up. • Raise the hood and support it with the strut (3) in the yellow colored retainer, ensuring it is secure. Hold the support at the yellow colored insulation section. To close, replace the support strut in its retaining clip, lower the hood and allow it to drop into the catch for the last 20 - 30 cm (8 - 12 inches).
Maintenance and care 2.0 litre EFI-engine compartment Power steering reservoir Windshield washer fluid reservoir Engine coolant reservoir Engine oil dipstick Automatic transaxle dipstick (if equipped) Engine oil filler cap Brake fluid reservoir Air cleaner Battery Power distribution box For ease of identification, all filler caps and the engine oil dipstick are marked yellow/black.
Maintenance and care 2.5 litre EFI-engine compartment Power steering reservoir Engine coolant reservoir Windshield washer fluid reservoir Engine oil dipstick Brake Automatic fluid transaxle reservoir dipstick (if equipped) Engine oil filler cap Battery Air cleaner Power distribution box For ease of identification, all filler caps and the engine oil dipstick are marked yellow/black.
Maintenance and care Engine oil Use SAE 5WĆ30 motor oil CERTIFIED FOR GASOLINE ENGINES by the American Petroleum Institute. Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by Ford or Lincoln/Mercury Warranty. Checking the engine oil Check the engine oil each time you fuel your vehicle. To check the oil: 1. Make sure the vehicle is on level ground.
Maintenance and care 6. If the oil level is below the minimum line, add engine oil as necessary. If the oil level is beyond the maximum line, engine damage or high oil consumption may occur and some oil must be removed from the engine by a service technician. 7. Put the dipstick back in and ensure it is fully seated. Continuous contact with used motor oil has caused cancer in laboratory mice. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2.
Maintenance and care Refer to the Scheduled Maintenance Guide" for additional information. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application. Always dispose of used automotive fluids in a responsible manner. Follow your community's standards for disposing of these types of fluids. Call your local recycling center to find out more about recycling automotive fluids.
Maintenance and care Brake/clutch fluid reservoir Brake and clutch fluid systems are supplied from the same reservoir. The level of the fluid must lie between the MIN and MAX marks on the side of the reservoir. If the level falls below the MIN mark, the brake fluid level warning light on the instrument panel will illuminate. Add only DOT 3 or DOT 4 brake fluid that meets the Ford specification (see the Capacities and specifications chapter).
Maintenance and care Engine coolant maintenance Do not put engine coolant in the container for the windshield washer fluid. Use Ford Extended Life Engine Coolant F6AZĆ19544ĆAA or an equivalent DEXĆCOOL coolant or a coolant meeting Ford specification WSSĆM97B44ĆD. Ford Extended Life Engine Coolant is a silicateĆfree coolant. Do not add conventional coolant or recycled coolant to your vehicle. If you are unsure which type of coolant your vehicle requires, contact your local dealer.
Maintenance and care Check the coolant level in the coolant recovery reservoir the next few times you drive the vehicle. If necessary, add enough of a 50/50 mixture of coolant and water to bring the liquid level to the fill mark on the reservoir. Never remove the coolant recovery cap while the engine is running or hot. If you must remove the coolant recovery cap, follow these steps to avoid personal injury. 1. Before you remove the cap, turn the engine off and let it cool. 2.
Maintenance and care Recycled engine coolant Ford Motor Company recommends that Ford and LincolnĆMercury dealers use recycled engine coolant produced by FordĆapproved processes. Not all coolant recycling processes produce coolant which meets Ford specifications ESEĆM97B44ĆD, and use of such coolant may harm the engine and cooling system components. Always dispose of used automotive fluids in a responsible manner. Follow your community's standards for recycling and disposing of automotive fluids.
Maintenance and care Severe winter climate If you drive in extremely cold climates (less than Ć36ºC [Ć34ºF]), it may be necessary to increase the coolant concentration above 50%. Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle is such that the coolant will not freeze at the temperature level in which you drive during the winter months. Never increase the engine coolant concentration above 60%.
Maintenance and care Automatic transaxle fluid Follow the scheduled service intervals outlined in the "Scheduled Maintenance Guide." Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick and/or dipstick handle and also in the Lubricant specifications section in the Capacities and specifications chapter. Do not drive the vehicle if the fluid level is below the hole at the bottom of the dipstick and outside temperatures are above 10°C (50°F).
Maintenance and care The transaxle fluid should be in this range if at normal operating temperature 66°C - 77°C (150°F - 170°F). The transaxle fluid should be in this range if at room temperature 10°C - 35°C (50°F - 95°F). If your vehicle has been operated for an extended period at high speeds, in the city during hot weather or pulling a trailer, the vehicle should be turned off for about thirty minutes to allow the fluid to cool before checking. 1.
Maintenance and care 4. Remove the dipstick, wiping it clean with a clean, dry, lint free rag. 5. Install the dipstick making sure it is fully seated in the filler tube. 6. Remove the dipstick and inspect the fluid level. The fluid level should be in the crosshatched area on the dipstick. 7. If necessary, add fluid in .25 litre (1/2 pint) increments through the filler tube until the level is correct. 8. If an overfill occurs, excess fluid should be removed by a qualified technician.
Maintenance and care Battery Your vehicle may be equipped with a Motorcraft maintenanceĆfree battery. The Motorcraft maintenanceĆfree battery normally does not require additional water during its life of service. However, for severe service usage or in high temperature climates, refer to the Scheduled Maintenance Guide" for additional information. Keep the electrolyte in each cell up to the level" indicator. Do not overfill the battery cell.
Maintenance and care Battery replacement If your original equipment battery requires replacement while under warranty, it will be replaced with a Motorcraft service battery, identical in design technology. Like the original equipment battery, it should not require water addition during its normal life of service; however, for severe service usage or in high temperature climates, refer to the Scheduled Maintenance Guide" for additional information. Do not overfill the battery cell.
Maintenance and care Applying too much pressure on the ends when lifting a battery could cause acid to spill. Lift the battery with a carrier or with your hands on the opposite corners. Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.
Maintenance and care Relearning the idle function Because your vehicle's engine is electronically controlled, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the computer must relearn" its idle conditions before your vehicle can drive properly. To begin this process: 1. Put the automatic transaxle gearshift in P (Park). Put the manual transaxle gearshift in neutral. 2. Turn off all accessories and start the vehicle. 3.
Maintenance and care Checking wiper blades Check the wiper blades on your vehicle for roughness by running the tips of your fingers over the edge of the blade. Traces of grease, silicone and fuel prevent wiper blades from functioning properly. We recommend Ford cleaning solutions or equivalent to clean wiper blades. Change the wiper blades on your vehicle at least once a year.
Maintenance and care 2. Remove the plastic caps from the screws on the grille. Remove the screws. 3. Open the hood. Pull off the rubber weatherstrip at the back of the engine compartment. Remove the screws that hold the grille, separate the two halves and remove the grille. 4. The filter is in a housing at the back of the engine compartment, on the left side. Pull off the two clips on the sides of the housing. Slide out the housing and filter. 5.
Maintenance and care INFORMATION ABOUT TIRE QUALITY GRADES New vehicles are fitted with tires that have their Tire Quality Grade (described below) molded into the tire's sidewall. These Tire Quality Grades are determined by standards that the United States Department of Transportation has set. Tire Quality Grades apply to new pneumatic tires for use on passenger cars.
Maintenance and care Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and oneĆhalf (1 1/2) times as well on the government course as a tire graded 100.
Maintenance and care Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Maintenance and care Checking tire pressure Check the tire pressure periodically after the vehicle has been parked for at least one hour or has been driven less than 5 km ( 3 miles). Inflate the tires as necessary. To check the tire pressure, insert the tire pressure gauge into the valve. The cold pressure amount is listed on the tire instruction decal located on the passenger's door. Improperly inflated tires can affect vehicle handling and can fail suddenly, possibly resulting in loss of vehicle control.
Maintenance and care Replacing tires " " ! % ! # ' ' $ $ % % ' $ $ $ $ " $ ! $ ! $ $ $
Maintenance and care ! ! % " ! % " $ " # " ! " " " !" # " " " " ! ! ' " % " & ! #! " ! $ # ! " " ! & # $ !# " & # # ! $ " " !# " " " " " "& ! #! Using snow tires and chains % " ! #!" " ! ! ' ! " " ! & # # " & $ & # $ " ! & # $
Maintenance and care Follow these guidelines when using snow tires: • If possible, avoid fully loading your vehicle. • The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires.
Maintenance and care IMPORTANT FUEL INFORMATION Important safety precautions
Maintenance and care Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Make sure the fuel cap is correctly fitted after fueling. Failure to do so may cause the on board diagnostic system to illuminate the light. • Automotive fuels can be harmful or fatal if swallowed. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent.
Maintenance and care Choosing the right fuel Use only unleaded fuel. The use of leaded fuel is prohibited by law and could damage your vehicle. The damage may not be covered by your warranty. Your vehicle was not designed to use fuel containing manganeseĆbased additives such as MMT. Additionally, vehicles certified to California emission standards (indicated on the underhood Vehicle Emission Control Information label) are designed to operate on California reformulated gasolines.
Maintenance and care Octane recommendations Your vehicle is designed to use regular gasoline with an (R+M)/2 octane rating of 87. We do not recommend gasolines labeled as regular" in high altitude areas that are sold with octane ratings of 86 or even less. Do not be concerned if your vehicle sometimes knocks lightly. However, if it knocks heavily under most driving conditions on the recommended octane, see your dealer or a qualified service technician to prevent any engine damage.
Maintenance and care Fuel quality If you are experiencing starting, rough idle or hesitation problems try a different brand of fuel. If the condition persists, see your dealer or qualified service technician. The American Automobile Manufacturers Association (AAMA) issued a gasoline specification to provide information on high quality fuels that optimize the performance of your vehicle. We recommend the use of gasolines that meet the AAMA specification if they are available.
Maintenance and care When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap, align the tabs on the cap with the notches on the filler pipe. 5. Turn the filler cap clockwise 1/8 of a turn until it stops. If the "check engine" indicator comes on and stays on when you start the engine, the fuel filler cap may not be properly installed.
Maintenance and care Calculating fuel economy To accurately calculate your vehicle's fuel economy: 1. Fill the tank completely and record the initial odometer reading. 2. Each time you fill the tank, record the amount of fuel added (in litres or gallons). 3. After at least three to five fillĆups, fill the fuel tank and record the current mileage reading. 4. Use one of the following equations to calculate fuel economy.
Maintenance and care EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. To make sure that the catalytic converter and other emission control components continue to work properly: • Use only unleaded fuels. • Avoid running out of fuel. • Do not turn off the ignition while your vehicle is moving, especially at high speeds.
Maintenance and care If other than Ford, Motorcraft or Ford authorized parts are used for maintenance replacements or for service of components affecting emissions control, such nonĆFord parts should be equivalent to genuine Ford Motor Company parts in performance and durability. Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire.
Maintenance and care Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle's emission system is on the Vehicle Emission Control Information Decal located on or near the engine.
Maintenance and care Readiness for inspection/ maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the onĆboard diagnostic (OBDĆII) system. If your check engine" light is on, refer to the description in the Warning Lights and Chimes section of the Instrumentation chapter. Your vehicle may not pass the I/M test with the check engine" light on.
Maintenance and care BULB REPLACEMENT Removing the headlamps assembly Handle a halogen headlamp bulb carefully and keep out of children's reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used. The bulbs for the low beam, high beam, turn signals and side lamps are housed in the lamp assembly.
Maintenance and care Front turn signal Parking lamps Opening the headlamp assembly
Maintenance and care Headlamps – low beam Headlamps – high beam Headlamp alignment Aiming the headlamps
Maintenance and care Reinstalling the headlamp assembly All bulb connectors must be correctly connected. Install in the reverse order. Foglamps (if equipped) 1. Open the flap in the lower radiator grille. 2. Remove the screw and pull the foglamp assembly out. 3. Disconnect the electrical connector. 4. Remove the cover from the rear of the foglamp assembly. 5. Disconnect the electrical connectors and release the wire clip from the bulb. 6.
Maintenance and care Side marker lamps 1. Push the complete light assembly to the front and pull it out. 2. Remove the glass from the assembly by turning it counterclockwise. 3. Pull the bulb out and replace it. Brake/turn signal/tail/backup lamps 1. From the trunk, remove the carpet cover from the lamp assembly. 2. Remove the three retainer nuts and pull the lamp assembly out. 3. Turn the bulb counterclockwise and pull it out. 4. Replace the defective bulb.
Maintenance and care License plate lamp Luggage compartment lamp High mounted brake lamp
Maintenance and care Interior lamps Switch off the interior lamps (middle switch position). Pry out the lamp assembly with a flat screwdriver, release the reflector at the side and replace the festoon bulb. To install, fit the new bulb in reverse sequence. Reading lamps (if equipped) Open the lamp assembly. The bulbs can be replaced after the contact plate has been hinged back.
Maintenance and care AIMING THE HEADLAMPS The alignment of your headlamps should be checked if: • Oncoming motorists frequently signal you to deactivate your high beams, and your high beams are not activated. • The headlamps do not seem to provide enough light for clear night vision. • The headlamp beams are pointed substantially away from a slightly down and to the right position. Aiming the headlamps Your vehicle is equipped with a Vehicle Headlamp Aim Device (VHAD) on each headlamp body.
Maintenance and care CAUTION: THE VERTICAL AIM MUST BE ADJUSTED FIRST. You will need a 6 mm Allen wrench or a Phillips screwdriver. If the vehicle has been in an accident, the vehicle's front structure should be properly aligned before aiming the headlamp. Adjusting the vertical aim 1. Park the vehicle . 2. The vertical indicator is located on top of the headlamp assembly; the adjusting screw is located behind the headlamp assembly. 3.
Maintenance and care Adjusting the horizontal aim CAUTION: Do not adjust the horizontal aim until after adjusting the vertical aim. 1. Park the vehicle . 2. The horizontal indicator and the adjusting screw are located behind the headlamp assembly. 3. Turn the horizontal adjusting screw until the indicator in the vial aligns with the 0" mark on the plastic slide located on the indicator housing (vial).
Maintenance and care VEHICLE CARE Washing your vehicle # ! # # # # # ! ! ! # # # # ! ! # ! # ! ! ! ! # "
Maintenance and care ! # ! # ! # " ! # ! # # Waxing your vehicle ! #
Maintenance and care Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touchĆup paint, paint repair foil or aerosol spray from the Ford accessories line. Observe the application instructions on the products. Cleaning the wheels Wash the wheels with the same detergent you use to clean the body of your vehicle. Do not use acidĆbased wheel cleaners, steel wool, fuel or strong detergents. Never use abrasives that will damage the finish of special wheel surfaces.
Maintenance and care Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup act as insulators and keep the engine warmer than normal. Follow these guidelines to clean your engine: • Take care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and cause damage. • Do not spray with cold water as this may crack the engine block. • Cover the alternator and battery to prevent water damage when cleaning the engine.
Maintenance and care Cleaning plastic exterior parts Use a vinyl cleaner for routine cleaning of plastic. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleumĆbased cleaners. Cleaning the exterior lamps Wash the exterior lamps with the same detergent you use to wash the exterior of your vehicle. Use glass cleaner or tar remover if necessary.
Maintenance and care Cleaning the instrument panel ! " ! " " ! Cleaning the interior fabric ! ! " ! ! C
Maintenance and care Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets and warm water. Do not bleach or dye the belts, because these actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are no nicks, wear or cuts. Ford recommends that all safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision.
Capacities and specifications Motorcraft parts Part number Component 2.0 litre engine 2.5 litre engine Spark plug* AZFSĆ22F # 1+2** AZFSĆ22FE # 3+4 AWSFĆ32F FAĆ1612 FAĆ1613 FP4 FP4 Fuel filter FGĆ800A FGĆ800A Oil filter FLĆ2005 FLĆ820 Battery BXTĆ40R BXTĆ40R PCV valve EVĆ224 EVĆ152 Crankcase ventilation filter FAĆ1621 - Air filter Cabin air filter * Refer to Vehicle Emission Control Information (VECI) decal for spark plug and gap specifications.
Capacities and specifications Capacities Engine oil - with filter - without Manual transaxle Automatic transaxle Power steering Cooling system with heating Windshield washer fluid Fuel tank Braking system * ** 2.0 litre engine 2.5 litre engine 4.25 l (4.5 qts) 3.75 l (4.0 qts) 5.5 l (5.8 qts) 5.0 l (5.3 qts) 2.6 l (2.7 qts) 8.5 l (9.0 qts) 9.6 l (10.2 qts) Fill to MAX mark 6.6 l (7.0 qts)* 7.1 l (7.5 qts)** 9.5 l (10.0 qts)* 9.7 l (10.2 qts)** Fill to top of reservoir 58.5 litres (15.
Capacities and specifications Lubricant specifications Item Ford part name or equivalent Ford part number Ford specification Brake fluid High performance DOT 3 brake fluid or DOT 4 brake fluid C6AZĆ19542ĆAB for DOT 3 ESAĆM6C25ĆA or ESDĆM6C57ĆA Engine coolant (orange) Ford Extended Life Engine Coolant F6AZĆ19544ĆAA WSSĆM97B44ĆD or DEXĆCOOL equivalent Engine oil Motorcraft motor oil 5WĆ30 super preĆ mium XOĆ5W30ĆQSP American Petroleum Institute CertifiĆ cation Mark and WSSĆM2C153ĆG Power stee
Capacities and specifications Engine data Engine cm3 Cubic capacity Power output kW(HP) at rpm Max torque Nm (lbĆft.) at rpm 2.0 litre engine 2.5 litre engine 1988 2544 96(125) 5500 125 (170) 6250 176 (130) 4000 220 (162) 4250 Fuel grade 87 Octane Continuous engine speed rpm 6150 6700 Max.
Capacities and specifications Dimensions mm (inches) A = Overall length 4699 (185) B = Overall width (without mirrors) 1769 (69.6) C = Overall height (curb weight) 1325 (52.2) D = Wheelbase 2704 (106.5) E = Track 234 front 1506 (59.3) rear 1491 (58.
Capacities and specifications VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is attached to a metal tag and is located on the front driver's side of the instrument panel. The VIN tag may be seen by looking through the windshield from the outside of the vehicle.
Customer assistance GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern. Ford offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24Ćhours, seven days a week • for the Basic warranty period (Canada) or New Vehicle Limited Warranty period (U.S.
Customer assistance Ford extended service plan You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.S.) and Ford of Canada (in Canada).
Customer assistance Getting the service you need At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. When you need warranty repairs your selling dealer would like you to return to it for that service, but you may also take your vehicle to another Ford Motor Company dealership authorized for warranty repairs. Certain warranty repairs require special training though, so not all dealers are authorized to perform all warranty repairs.
Customer assistance Please have the following information available when contacting Ford Customer Assistance: • Your telephone number (home and business) • The name of the dealer and the city where the dealership is located • The year and make of your vehicle • The date of vehicle purchase • The current odometer reading • The vehicle identification number (VIN) If you still have a complaint involving a warranty dispute, you may wish to contact the Dispute Settlement Board (U.S.
Customer assistance • sales disputes between customer and dealer except those associated with warranty repairs or concerns with the vehicle's performance as designed • a request for reimbursement of consequential expenses unless a service or product concern is being reviewed • items not covered by the New Vehicle Limited Warranty (including maintenance and wear items) • alleged personal injury/property damage claims • cases currently in litigation • vehicles not used primarily for family, personal or househ
Customer assistance To properly review your case, the Board needs the following information: • legible copies of all documents and maintenance or repair orders relevant to the case • the year, make, model, and Vehicle Identification Number (VIN) listed on your vehicle ownership license • the date of repair(s) and mileage at the time of occurrence(s) • the current mileage • the name of the dealer(s) who sold or serviced the vehicle • a brief description of your unresolved concern • a brief summary of the act
Customer assistance After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board's decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.
Customer assistance GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can only get fuel with an antiĆknock index lower than is recommended for your vehicle, contact a district or owner relations/customer assistance office.
Customer assistance FORD ACCESSORIES FOR YOUR VEHICLE Ford has many quality products available from your dealer to clean your vehicle and protect its finishes.
Customer assistance Comfort and convenience Air conditioner Air filtration systems Cargo nets Cargo organizers Cargo shades Cargo trays Dash trim Engine block heaters Gear shift knob Luggage presenter (Continental only) Manual sliding rear window Tire step Travel equipment Console Console armrest Daytime running lights Factory luggage rack Factory luggage rack adapters Fog lights Framed luggage covers HeavyĆduty battery Neutral towing transfer case kit (Explorer 4.
Customer assistance Protection and appearance equipment Air bag antiĆtheft locks Bed mat/bedliner tailgate covers Bed mats Bedliners Car/truck covers Cargo liners, interior Carpet floor mats Cleaners, waxes and polishes Flat splash guards Frond end covers (full and mini) Hood deflectors Locking gas cap Lubricants and oils Molded splash guards Molded vinyl floor mats Rallye bars Rear air deflectors Rear decklid spoilers Side window air deflectors Spare tire lock Step bumpers Step/sill plates Tailgate covers
Customer assistance • Mobile communications systems may harm the operation of your vehicle, particularly if they are not properly designed for automotive use or are not properly installed. When operated, such systems may cause the engine to stumble or stall. In addition, such systems may be damaged or their performance may be affected by operating your vehicle.
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Index Accessories . . . . . . . . . . . . . . . . . 243 Additives, engine oil . . . . . . . . . 178 Air bag disposal . . . . . . . . . . . . . 109 Air bag readiness light . . . . . . . . . . 9 Air bag supplemental restraint system . . . . . . . . . . . . . . . . . . . . . 100 Air bag system, side . . . . . . . . . . 106 Air conditioning . . . . . . . . . . . . . . 27 Air filter . . . . . . . . . . . . . . . . . . . . 230 Alarm, activating panic . . . . . . . . 83 AntiĆlock brake system (ABS) light .
Index Electrical system . . . . . . . . . . . . 152 Emergencies, roadside . . . . . . . 150 Emission control system . . . . 6, 209 Engine block heater . . . . . . . . . . 126 Engine compartment . . . . . . . . . 176 Engine coolant . . . . . . . . . 182, 232 Engine coolant temperature gauge . . . . . . . . . . . . . . . . . . . . . . . 16 Engine data . . . . . . . . . . . . . . . . . 233 Engine oil . . . . . . . . . 178, 231, 232 Engine oil pressure warning light 11 Engine, cleaning . . . . . . . . .
Index Key coding . . . . . . . . . . . . . . . . . . 88 KeyĆinĆignition warning chime . . 15 Keys . . . . . . . . . . . . . . . . . . . . . . . . 86 License plate lamp . . . . . . . . . . . 218 Liftgate . . . . . . . . . . . . . . . . . . . . . 80 Lights, warning and indicator . 6, 14 Load limits . . . . . . . . . . . . . . . . . 139 Loading your vehicle . . . . . . . . . 139 Low coolant warning light . . . . . . 12 Lubricant specifications . . . . . . 232 Luggage compartment . . . . . .
Index Safety belt extension assembly . 98 Safety belt height . . . . . . . . . . . . . 97 Safety belt maintenance . . . 99, 229 Safety belt warning chime . . . 15, 97 Safety belt warning light . . . . 10, 97 Safety belts . . . . . . . . . . . . . . . 10, 92 Safety Compliance Certification Label . . . . . . . . . . . . . . . . . . . . . . 145 Safety defects, reporting . . . . . . 248 Safety restraint locking modes . . 95 Safety restraints . . . . . . . . . . . . . . 92 Safety restraints . . . . . . . . . .
Index Used automotive fluids, disposal . . . . . . . . . . . . . . . . . . . . 180 Vehicle care . . . . . . . . . . . . . . . . 223 Vehicle Emission Control Information (VECI) . . . . . 209, 211 Vehicle identification number (VIN) . . . . . . . . . . . . . . . . . . . . . . 235 Ventilating your vehicle . . . . . . . 121 Vents . . . . . . . . . . . . . . . . . . . . . . . 25 Viscosity. Engine oil Washer fluid warning light . . . . . 19 Washing your vehicle . . . . . . . . .
Filling station information Fuel UNLEADED FUEL ONLY Octane 87 Fuel tank capacity 58.5 litres (15.
