8000 Cover a/w 4/4/00 5:13 pm Page 5 M E R I D I A N D S P L O U D S P E A K E R U S E R G U I D E
Meridian DSP Loudspeaker User Guide #$ 2!$)/ $6$ &UNCTION 4OP -ENU !58 $)3# 4!0% 46 #!",% 3!4 6#2 6#2 '!-% /&& 0OWER 0AGE !UDIO 0AGE %NTER 3LOW /PEN -ENU 2ETURN 2EPEAT 3ETUP 2ECORD "AND !NGLE i 3UBTITLE $30 3TORE #LEAR 0HASE !" /3$ $ISPLAY -UTE
PREFACE Important safety instructions • • • • Read the instructions. Keep these instructions. Follow all instructions. Do not use this apparatus near water. • Clean only with a dry cloth. • Install only in accordance with the manufacturer’s instructions. • Refer all servicing to approved service personnel. Safety warnings WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE • Do not expose the speakers to dripping or splashing.
Contents Introduction 1 Meridian DSP loudspeakers 2 Sample configurations 5 Available accessories 6 DSP5000 and DSP5000C Unpacking 7 8 Specifications 10 DSP5200 and DSP5200HC 13 Unpacking 14 Specifications 17 DSP5500, DSP5500HC, and DSP5500C 19 Unpacking 20 Specifications 22 DSP6000 and DSP6000C 25 Unpacking 26 Specifications 29 DSP7000 31 Unpacking 32 Specifications 34 Connecting up the DSP loudspeakers 37 Connecting the loudspeakers 38 Connecting to other equipment 4
Using the DSP loudspeakers 45 Selecting a source 46 Changing the display 47 Adjusting the volume 48 Changing the treble, bass, or phase 49 Changing the listening position 50 Configuring the DSP loudspeakers 51 Choosing standard settings 52 Specifying information about your system 54 Configuring the sources 55 Configuring the setup options 57 Troubleshooting 59 Troubleshooting 60 Cleaning 62 Service and guarantee 63 Index 65 iv
PREFACE Copyright and acknowledgements Sales and service in the UK Sales and service in the USA Meridian Audio Ltd Latham Road Huntingdon Cambridgeshire PE29 6YE England Meridian America Inc 8055 Troon Circle Suite C Austell GA30168-7849 USA Tel (01480) 445678 Fax (01480) 445686 Tel (404) 344 7111 Fax (404) 346 7111 World Wide Web – http://www.meridian-audio.
PREFACE vi
Introduction Welcome to the Meridian DSP loudspeaker range. This User Guide provides full information about using the DSP loudspeakers in conjunction with your other equipment, to achieve the superb results you can expect from them.
INTRODUCTION Meridian DSP loudspeakers Meridian DSP loudspeakers represent the fruits of more than 25 years of continuous development of loudspeakers as musical instruments. The finest materials and state-of-the-art design are combined to create what we believe is the ultimate range of home loudspeakers.
INTRODUCTION Power amplifiers The speakers are driven by multiple independent high-power, lowfeedback power amplifiers. The combination of idealised magnetic design, careful star earthing, and very fast output devices gives the amplifiers extremely low noise, high detail, and fast bass. The whole electronic assembly is supplied from substantial toroidal transformers feeding high-quality, audiophile-grade capacitors.
INTRODUCTION Meridian High Resolution (MHR) All Meridian DSP loudspeakers support Meridian High Resolution (MHR), to allow you to connect to other MHR-compliant Meridian products to take advantage of high-rate audio sources, and provide the additional benefits of lower jitter and improved sound quality on all sources.
INTRODUCTION Sample configurations Meridian Digital Theatre™ $30 (# $30 $30 $30 $30 ' $6$ !UDIO 4RANSPORT Open Display ' ! $6$ 0LAYER 0REAMPLIFIER 4UNER (OME wxy z{| -/.
INTRODUCTION Available accessories Each DSP loudspeaker is shipped complete with cables to enable it to be used in a Meridian Digital music system. In addition, each pair of main loudspeakers is supplied with a MSR+ remote. Other applications, and some advanced features, may require one or more of the following accessories, which can be purchased from your Meridian dealer: • Additional S5 leads (8m and 14m).
DSP5000 and DSP5000C This chapter explains how to unpack and install the DSP5000 and DSP5000C, and gives specifications.
DSP5000 AND DSP5000C Unpacking Before you begin installation you should ensure that your DSP loudspeakers are the correct voltage for your local AC supply. If they are not, do not try to install them, and contact your dealer. You should not make any connections to the DSP loudspeakers, or to any other component in your system, while the AC power supply is connected and switched on.
DSP5000 AND DSP5000C • On solid floors fit the protectors over the spikes. • When all four feet have been fitted, carefully set the DSP loudspeakers upright in their playing positions and remove the rest of the packaging. • Adjust the feet until the speakers are stable, and then tighten the lock nuts. To fit the rubber bumpons (DSP5000C only) • Attach four bumpons to the underside of each speaker, using the selfadhesive pads.
DSP5000 AND DSP5000C Specifications Digital inputs and outputs • 2 x cable inputs, 32–96kHz. FIFO locks at 44.1, 48, 88.2, or 96kHz ±150ppm. • PCM using IEC958, or MHR connection support with auto-detection. • 1 x cable input pass-through to feed second speaker. Signal processing • 1 x Motorola 56303 running at 80MHz. • 2 x 24-bit Multi-bit delta-sigma DACs with 128x oversampling. • Crossover linear-phase ±30º at 2.3kHz.
DSP5000 AND DSP5000C Cabinet • • • • • Wood-veneered MDF with internal bracing and damping. Available in black ash, rosewood, or cherry. DSP5000: 210mm x 900mm x 297mm (8.3" x 35.4" x 11.7") (W x H x D). DSP5000C: 670mm x 195mm x 275mm (26.3" x 7.7" x 10.8") (W x H x D). 32kg (70lb) each. Power • 100-125; 200-250V AC 50-60Hz. • 20VA standby; 300VA max. Meridian Audio reserves the right to amend product specifications at any time.
DSP5000 AND DSP5000C 12
DSP5200 and DSP5200HC This chapter explains how to unpack and install the DSP5200 and DSP5200HC, and gives specifications.
DSP5200 AND DSP5200HC Unpacking Before you begin installation you should ensure that your DSP loudspeakers are the correct voltage for your local AC supply. If they are not, do not try to install them, and contact your dealer. You should not make any connections to the DSP loudspeakers, or to any other component in your system, while the AC power supply is connected and switched on.
DSP5200 AND DSP5200HC Meridian Audio has supplied products using lacquer finishes for many years and we are confident that when carefully used your product will return a lifetime’s enjoyment. To fit the feet (DSP5200 only) The feet ensure that the loudspeakers have a stable base, and can be adjusted to allow for uneven floors. Use the spikes for carpeted floors; they are designed to penetrate the pile without damaging or flattening the carpet. Retract the spikes for solid floors.
DSP5200 AND DSP5200HC Removing the grilles The grilles are deliberately designed to fit tightly to avoid vibration during operation, and they should be removed using the following procedure to avoid damaging the loudspeaker. The grille consists of elastic material stretched tightly over a plastic ring. The plastic ring includes two indentations at the three o‘clock and nine o‘clock positions, which you can locate by gently depressing the grille fabric.
DSP5200 AND DSP5200HC Specifications Digital inputs and outputs • 2 x cable inputs, 32–96kHz. FIFO locks at 44.1, 48, 88.2, or 96kHz ±150ppm. • PCM using IEC958, or MHR connection support with auto-detection. • 1 x 24-bit Multi-bit delta-sigma DACs with 128x oversampling. Signal processing • 2 x Motorola 56367 running at 150MHz. • 4 x 24-bit Multi-bit delta-sigma DACs with 128x oversampling. • Crossover linear-phase ±30º at 2.6kHz.
DSP5200 AND DSP5200HC Cabinet • Entire speaker manufactured from interlaminated panels. • Individually covered grilles for bass units. • Finished in black or silver high-gloss lacquer, satin Santos rosewood, natural stain maple, black ash, or cherry. • DSP5200: 300mm x 903mm x 356mm (11.8" x 35.6" x 14.0") (W x H x D). • DSP5200HC: 735mm x 201mm x 267mm (29.0" x 7.9" x 10.5") (W x H x D). • 35kg (77lb) each. Power • 100-125; 200-250V AC 50-60Hz. • 20VA standby; 600VA max.
DSP5500, DSP5500HC, and DSP5500C This chapter explains how to unpack and install the DSP5500, DSP5500HC, and DSP5500C, and gives specifications.
DSP5500, DSP5500HC, AND DSP5500C Unpacking Before you begin installation you should ensure that your DSP loudspeakers are the correct voltage for your local AC supply. If they are not, do not try to install them, and contact your dealer. You should not make any connections to the DSP loudspeakers, or to any other component in your system, while the AC power supply is connected and switched on.
DSP5500, DSP5500HC, AND DSP5500C • Screw each foot into the threads on the bottom of the loudspeaker. Do not fully tighten the lock nut at this stage. • On solid floors fit the protectors over the spikes. • When all four feet have been fitted, carefully set the DSP loudspeakers upright in their playing positions and remove the rest of the packaging. • Adjust the feet until the speakers are stable, and then tighten the lock nuts.
DSP5500, DSP5500HC, AND DSP5500C Specifications Digital inputs and outputs • 2 x cable inputs, 32–96kHz. FIFO locks at 44.1, 48, 88.2, or 96kHz ± 150ppm. • PCM using IEC958, or MHR connection support with auto-detection. • 1 x 24-bit Multi-bit delta-sigma DACs with 128x oversampling. Signal processing • 2 x Motorola 56303 running at 80MHz. • 4 x 24-bit Multi-bit delta-sigma DACs with 128x oversampling. • Crossover linear-phase ±30º at 200Hz and 2.6kHz.
DSP5500, DSP5500HC, AND DSP5500C Cabinet • Thick MDF side panels sandwiched around steel plates for maximum damping across all frequencies. • Steel plates give magnetic shielding. • Side panels available in black ash and rosewood. • Separate mid-range enclosure built into main cabinet. • DSP5500 and DSP5500C: 284mm x 1100mm x 450mm (11.2" x 43.3" x 17.7") (W x H x D). • DSP5500HC: 1100mm x 285mm x 415mm (43.3" x 11.2" x 16.3") (W x H x D). • 65kg (143lb) each. Power • 100-125; 200-250V AC 50-60Hz.
DSP5500, DSP5500HC, AND DSP5500C 24
DSP6000 and DSP6000C This chapter explains how to unpack and install the DSP6000 and DSP6000C, and gives specifications.
DSP6000 AND DSP6000C Unpacking Before you begin installation you should ensure that your DSP loudspeakers are the correct voltage for your local AC supply. If they are not, do not try to install them, and contact your dealer. You should not make any connections to the DSP loudspeakers, or to any other component in your system, while the AC power supply is connected and switched on.
DSP6000 AND DSP6000C It is the nature of all lacquer finishes to shrink over time. This is unavoidable and may result in cabinet joint lines becoming visible. Meridian Audio has supplied products using lacquer finishes for many years and we are confident that when carefully used your product will return a lifetime’s enjoyment. To fit the feet The feet ensure that the loudspeakers have a stable base, and can be adjusted to allow for uneven floors.
DSP6000 AND DSP6000C • Connect the other end of each lead to the socket on the back of the base unit. Tightening the drive units The DSP loudspeakers typically take about two weeks of normal use for the drive units to settle. It is therefore recommended that you tighten the mounting bolts on each drive unit every few days during this period. Tighten the bolts in symmetrically opposite pairs using the 3mm hex wrench supplied. You should then check and if necessary retighten the drive units every few years.
DSP6000 AND DSP6000C Specifications Digital inputs and outputs • 2 x cable inputs, 32–96kHz. FIFO locks at 44.1, 48, 88.2, or 96kHz ±150ppm. • PCM using IEC958, or MHR connection support with auto-detection. • 1 x 24-bit Multi-bit delta-sigma DACs with 128x oversampling. Signal processing • 2 x Motorola 56303 running at 80MHz. • 4 x 24-bit Multi-bit delta-sigma DACs with 128x oversampling. • Crossovers linear-phase ±30º at 200Hz and 2.6kHz.
DSP6000 AND DSP6000C Cabinet • Head enclosure manufactured from interlaminated panels with internal damping and bracing. • Glass front. • Head finished in high-gloss black piano lacquer. • 275mm x 1330mm x 425mm (10.8" x 52.4" x 16.7") (W x H x D). • 9.5kg (21lb) each. Power • 100-125; 200-250V AC 50-60Hz. • 6VA idle; 200VA max. Meridian Audio reserves the right to amend product specifications at any time.
DSP7000 This chapter explains how to unpack and install the DSP7000, and gives specifications.
DSP7000 Unpacking Before you begin installation you should ensure that your DSP loudspeakers are the correct voltage for your local AC supply. If they are not, do not try to install them, and contact your dealer. You should not make any connections to the DSP loudspeakers, or to any other component in your system, while the AC power supply is connected and switched on. Unpacking The unpacking instructions are provided on a separate leaflet enclosed with the speakers.
DSP7000 It is the nature of all lacquer finishes to shrink over time. This is unavoidable and may result in cabinet joint lines becoming visible. Meridian Audio has supplied products using lacquer finishes for many years and we are confident that when carefully used your product will return a lifetime’s enjoyment. Tightening the drive units The DSP loudspeakers typically take about two weeks of normal use for the drive units to settle.
DSP7000 Specifications Digital inputs and outputs • 2 x cable inputs, 32–96kHz. FIFO locks at 44.1, 48, 88.2, or 96kHz ±150ppm. • PCM using IEC958, or MHR connection support with auto-detection. • 1 x 24-bit Multi-bit delta-sigma DACs with 128x oversampling. Signal processing • 2 x Motorola 56303 running at 80MHz. • 4 x 24-bit Multi-bit delta-sigma DACs with 128x oversampling. • Crossover linear-phase ±30º at 200Hz and 2.6kHz.
DSP7000 Cabinet • • • • • Entire speaker manufactured from interlaminated panels. MDF cloth-covered grille. Finished in high-gloss piano lacquer. 346mm x 1010mm x 450mm (13.6" x 39.8" x 17.7") (W x H x D). 50kg (110lb) each. Power • 100-125; 200-250V AC 50-60Hz. • 20VA standby; 600VA max. Meridian Audio reserves the right to amend product specifications at any time.
DSP7000 36
Connecting up the DSP loudspeakers This chapter explains how you should connect your DSP loudspeakers to the other audio equipment in your system.
CONNECTING UP THE DSP LOUDSPEAKERS Connecting the loudspeakers Back panel The following diagrams give details of the back panel connections: All speakers except DSP5200/DSP5200HC }Ì>Ê «ÕÌÃ }Ì>Ê ÕÌ«ÕÌ / "1/*1/ / Ê *1/ Ó£ Ã , Ê " "1/*1/ *1/ * ,-ÓÎÓ 8* - " DSP5200/DSP5200HC Ã *1/ "1/*1/ Ó £ ,-ÓÎÓ * *1/ "1/*1/ , Ê " - Ê Ã "1/*1/ *1/ }Ì>Ê ÕÌ«ÕÌ }Ì>Ê «ÕÌÃ Digital connections The following table gives details of the digital audio co
CONNECTING UP THE DSP LOUDSPEAKERS provide adequate shielding in the 1–30MHz region. Communications connections The following table gives details of the communications connections: Use this connection To connect to this COMMS INPUT The COMMS connection on a Meridian control unit or preamplifier. COMMS OUTPUT The COMMS INPUT on a second DSP loudspeaker. RS232 The serial port of a PC, to control the DSP loudspeaker using a computer. For more information see the Meridian Web site, http://www.
CONNECTING UP THE DSP LOUDSPEAKERS Connecting to other equipment To connect two DSP loudspeakers to a Meridian CD Player, Control Unit, or other digital source iÀ`>Ê Ê*>ÞiÀÊÀÊ ÌÀÊ1Ì / " - "1/*1/ xÊi>` -*ÊÕ`ëi>iÀÊqÊ->Ûi / Ê *1/ Ó £ -*ÊÕ`ëi>iÀÊqÊ >ÃÌiÀ / " "1/*1/ "1/*1/Ê *1/ / Ê *1/ Ó £ / " "1/*1/ "1/*1/Ê *1/ -xÊi>` You can create a complete system by connecting a pair of DSP loudspeakers directly to a digital source.
To connect three or more DSP loudspeakers in a Meridian surround system / " "1/*1/ "1/*1/Ê *1/ -*ÊÕ`ëi>iÀ iÌÀiÊ>ÃÌiÀ® iÀ`>Ê-ÕÀÀÕ`Ê*ÀViÃÃÀ " - / Ê"1/*1/- xÊi>` / Ê *1/ Ó £ CONNECTING UP THE DSP LOUDSPEAKERS x££Ê-«>ÌV ÊLÝ -xÊi>` -xÊi>`Ê`}Ì>ÊÕÕÃi`® -*ÊÕ`ëi>iÀÊqÊ >Ê, / Ê *1/ Ó £ / " "1/*1/ "1/*1/Ê *1/ -*ÊÕ`ëi>iÀÊqÊ >Ê / Ê *1/ Ó £ / " "1/*1/ "1/*1/Ê *1/ -xÊi>` If your system includes more than two Meridian DSP loudsp
CONNECTING UP THE DSP LOUDSPEAKERS To use a DSP loudspeaker as a centre speaker iÀ`>Ê-ÕÀÀÕ`Ê*ÀViÃÃÀ /, / " - "1/*1/ xÊi>` -*ÊÕ`ëi>iÀÊqÊ iÌÀi / Ê *1/ Ó £ / " "1/*1/ "1/*1/Ê *1/ You can use a single DSP loudspeaker as a centre speaker in a Meridian surround system. • Connect the speaker to the CENTRE digital output using an M5 lead, as shown in the illustration.
CONNECTING UP THE DSP LOUDSPEAKERS Positioning the digital loudspeakers To obtain the best sound For best results adjust the position of the loudspeakers while listening to music. If possible, have the most acoustically absorbent wall in the room behind the front speakers. Ideally have each DSP loudspeaker at least 0.5m (20") from a corner, and position them approximately 0.25m (10") from the wall.
CONNECTING UP THE DSP LOUDSPEAKERS 44
Using the DSP loudspeakers In systems with a Meridian preamplifier or control unit all of the functions of the DSP loudspeakers, including volume, treble, and bass, are operated via the controller. For more information refer to the user guide for the preamplifier or control unit, and you can ignore this chapter. The DSP loudspeakers can also be connected directly to up to two digital sources to create a complete, minimum system.
USING THE DSP LOUDSPEAKERS Selecting a source When not playing, the DSP loudspeakers should be left in the standby state. This uses a negligible amount of electricity, but ensures that the components of the loudspeakers operate at maximum efficiency from the moment you start. If you are not going to use the DSP loudspeakers for several days you should switch each unit completely off at the back panel, and disconnect it from the AC power supply.
USING THE DSP LOUDSPEAKERS Changing the display The DSP loudspeakers display information about the current settings on the 8-character front-panel display. In addition, three coloured indicators show status information. To change the displayed information • Press Display.
USING THE DSP LOUDSPEAKERS Adjusting the volume The DSP loudspeakers adjust the volume in precise steps of 1dB, where 9dB is equivalent to doubling the loudness, and can be varied in the range 1 to 99dB. When you first connect power to the DSP loudspeakers the volume is set to 65, which is similar to the midway position of the rotary volume control on a conventional preamplifier. To change the volume • Press the red A or V keys on the remote.
USING THE DSP LOUDSPEAKERS Changing the treble, bass, or phase The DSP loudspeakers provide sophisticated treble and bass controls, to allow you to adjust the broad balance of the system to correct for the acoustics of your listening room, or for a misbalanced recording. If you have a Meridian Surround Controller these functions are performed via the surround controller.
USING THE DSP LOUDSPEAKERS Changing the listening position The balance control of the DSP loudspeakers uses digital signal processing to compensate for an off-centre listening position by delaying and diminishing the sound in one speaker, thus effectively If you have a shifting the speaker’s image back. Meridian Surround Controller these functions are performed via the surround controller.
Configuring the DSP loudspeakers This chapter explains how to configure the DSP loudspeakers to suit the other equipment in your system. The first stage in configuring the DSP loudspeakers is to choose one of the standard settings, and these are designed to set all of the parameters to their most common values. You can also configure each setting individually for applications not catered for by one of the standard settings.
CONFIGURING THE DSP LOUDSPEAKERS Choosing standard settings The DSP loudspeakers provide the following five alternative standard settings, called Types, which configure all aspects of the DSP loudspeakers into the most commonly needed configurations: Type Description 1 Selects D1 for all sources. For use with a stereo system; eg a CD or DVD player such as the G08 or G91. 5 For use with a CD player connected to D1; all other sources use D2. 6 For use with a Meridian Surround Controller.
CONFIGURING THE DSP LOUDSPEAKERS To specify the speaker position • Press A or V to specify the speaker position. The options are shown in the following table: Display Position L. Left. R. Right. C. Centre (Type 6 only). S.L. Left surround (Type 6 only). S.R. Right surround (Type 6 only). To choose master or slave You should select one loudspeaker to be the master; this will normally be the centre channel. For more information see the chapter Connecting up the DSP loudspeakers, page 37.
CONFIGURING THE DSP LOUDSPEAKERS Specifying information about your system You can configure the operation of the DSP loudspeakers to suit the way your system is set up, and the way in which you want to use it. These settings are configured automatically to appropriate values when you choose one of the standard Type settings, and you should not normally need to alter them; see Choosing standard settings, page 52.
CONFIGURING THE DSP LOUDSPEAKERS Configuring the sources When the master DSP loudspeaker is set to one of the standard Types the 12 source selection keys on the remote select inputs D1 and D2 as shown in the table on page 52. If the configuration you want is not catered for by one of the standard settings, you can configure each source individually.
CONFIGURING THE DSP LOUDSPEAKERS The options are summarised in the table below: Option Initial value Alternatives Explanation Label Radio CD, Radio, LP, etc. The label used to identify the source on the front panel display. Audio input D1 D1 or D2. Choose D1 or D2 to specify the input. Comms type 2C 1C – 9C, or NC. Choose 1C for a Meridian CD player, 2C for a Meridian FM Tuner, 3C for a Meridian DVD player, or NC otherwise. Address 1A 1A – 8A. Allows you to have up to eight of type.
CONFIGURING THE DSP LOUDSPEAKERS Configuring the setup options When configuring the DSP loudspeakers, point the remote at the speakers, even if you have a Meridian Surround Controller. The setup options allow you to adjust the frequency response of the loudspeakers to compensate for their position. You only need to configure the master loudspeaker. To select Setup mode • Turn off the DSP loudspeaker using the power switch on the back panel.
CONFIGURING THE DSP LOUDSPEAKERS To adjust the centre frequency response and tilt offset If your system includes a DSP centre speaker you should set Centre Y on the master speaker. An additional frequency response option is then provided to allow you to adjust the centre speaker, with the options: C.Fre, C.bou, C.Sb1, C.Sb2, and C.Cor. • Press Function > or Function < until the display shows the current centre frequency response. C.
Troubleshooting This chapter provides suggested solutions to typical problems that may occur when setting up the DSP loudspeakers. If you are still not able to resolve a difficulty with the help of this guide and the suggestions in the following pages, please contact your Meridian dealer or Meridian Audio Ltd.
TROUBLESHOOTING Troubleshooting Display on front panel not lit Check the following: • There is AC power connected to the socket on the back of the DSP loudspeaker. • The power switch on the back panel of the DSP loudspeaker is turned on. If the display will still not illuminate, check any fuses in your power supply and the fuse in the inlet of the DSP loudspeaker. If these are all intact, contact your dealer. Remote not working Check the following: • The battery in the MSR+ remote.
TROUBLESHOOTING Drive units move when the speaker is switched on or off This is normal as the speaker active electronics settle. Configuring the DSP loudspeaker does not have any effect Make sure that you are configuring the DSP loudspeaker used as the master digital loudspeaker in the system. This determines the configuration of all digital loudspeakers in the system. Unit stays in standby • Check that it is connected correctly. • Turn the system on from another Meridian product in the system.
TROUBLESHOOTING Cleaning Cleaning (DSP5200, DSP5200HC, DSP6000, DSP6000C, and DSP7000 only) On black speakers, small marks on the lacquer surface can usually be removed by treating with Black Turtle Wax Color Magic. Do not use any coarse polish such as Auto Colour restorer, and always test any polish on a non-visible area first. Do not use any polish containing a solvent; these can cause crazing of the surface.
TROUBLESHOOTING Service and guarantee Service The Meridian components have been carefully designed to give years of untroubled service. There are no user-serviceable parts inside the case, nor do the units require any form of maintenance. In the unlikely event that your DSP loudspeaker fails to function correctly, it should be returned, in its original packaging, to your Meridian dealer. In case of difficulty within the UK or USA please contact the appropriate sales and service address shown on page v.
TROUBLESHOOTING 64
Index A absolute phase, changing accessories axis, changing F 49 6 50 frequency response, configuring G guarantee B back panel balance, changing bass, changing head units, installing 27 L lacquer finish 14, 26, 32 polishing 62 listening position, changing 50 3 58 42 58 62 39 39 39 54 57 55 38 40 M master, selecting Meridian comms Meridian Digital Music System Meridian Digital Theatre™ Meridian High Resolution (MHR) mounting options muting the sound 53 4 5 5 4 3 48 P phase, changing positioning t
speaker positioning specification DSP5000 and DSP5000C DSP5200 and DSP5200HC DSP5500, DSP5500HC, and DSP5500C DSP6000 and DSP6000C DSP7000 standard settings, selecting standby, switching to status indicators storing settings switching to standby 43 tilt offset, configuring treble, changing troubleshooting 10 17 22 29 34 52 46 47 58 46 U unpacking DSP5000 AND DSP5000C DSP5200 and DSP5200HC DSP5500, DSP5500HC, and DSP5500C DSP6000 AND DSP6000C DSP7000 8 14 20 26 32 V T tightening the drive units 58 49