V20230919 CFN-1310 Instruction Manual Read Carefully Before Installation Keep for Future Reference
CONTENTS Introduction.......................................................................................................... 1 Package List........................................................................................................ 2 Safety Information............................................................................................... 3 Preparation.......................................................................................................... 4 Initial Installation.......
Package List 2
Safety Information Warning! 1. T o reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. A ll wiring must be in accordance with national and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. This fan is suitable for use with solid-state speed controls. 4.
Preparation 1. Turn off Your Power Begin installation by removing fuses or turning off circuit breakers to the wiring you will be using. Use your compatible UL listed junction box if you already have one installed. Failure to disconnect the power supply prior to installation may result in serious injury or death. 2. Choose Your Mounting Position If you need to install a new UL listed junction box, secure it directly to your building's structure using appropriate fasteners and materials.
Initial Installation Junction Box Star Washer Mounting Bolt Junction Box Flat Washer Spring Washer Mounting Screw 1. Pass the supply wires through the central hole of the mounting bracket. 2. Secure the mounting bracket to your junction box with appropriate fasteners. For wood or other thinner and weaker ceilings, partially fasten the bracket using the mounting bolts and star washers.
Downrod Mounting 1. Remove the retaining clip and locking pin from the lower part of the 5″ downrod. 2. Unscrew the two Phillips bolts from the mount of this downrod. 3. Slide down the mount away from this downrod. 4. Pull the latch out of the upper slot of this downrod. Latch Mount Locking Pin Retaining Clip 5. Select either the 5″ or the 10″ downrod to match the height of your ceiling. Then, pass the downrod through the coupling cover as shown. 6.
9. Partially fasten the downrod by replacing the previously removed locking pin and retaining clip. 10. Retighten the previously loosened bolts until the downrod is locked into place. Failure to reattach the locking pin and retighten the Phillips bolts can cause the fan to fall from the ceiling during operation. KCY 12 3 KCYY KC 12 3 Locking Pin Retaining Clip 11. Slide down the coupling cover. Place the grommet and canopy onto the downrod’s top and then slide them to the coupling cover as shown. 12.
13. Insert the removed latch back into the downrod’s upper slot. 14. Slide up the downrod’s mount, rotating until the latch is firmly seated inside the mount. 15. Replace and tighten the removed Phillips bolts onto the mount. Latch KCY 12 3 KCY 12 3 16. Release the cable lock by loosening its Phillips bolt. Unwind the safety cable loop, wrap the cable around the mounting bracket, and thread it back through the lock. Retighten the bolt to re-secure the lock. 17.
Circuit Connections Again, ensure that the power has been cut before working with the wiring. Use the wire nuts provided with your fan. Ensure there are no loose wires or connections and secure connectors with electrical tape. 1. Connect the plugs from the receiver to those from the fan motor assembly as shown. 2. Connect the 2 colored wires of the receiver to the 2 identically colored wires from the junction box (Black: Live; White: Neutral).
4. Insert the receiver into the tray with the receiver facing the ceiling. For best results, make sure the white antenna on the end of the receiver remains extended and not tangled with any of the electrical wires. 5. Tuck all the connections neatly into the junction box.
Canopy Installation 1. Slide the canopy up to the mounting bracket and place the key holes over the bolts preinstalled on the bracket. Rotate the canopy until the bolts’ heads lock in place at the narrow sections of the key holes. Tighten these bolts as needed. Key Hole Canopy Bolt 2. Attach the grommet to the bottom of the canopy using its magnets.
Fan Blade Installation 1. Place one blade on the fan motor assembly, aligning their holes. 2. Making sure the blade is straight, attach two blade bolts WITHOUT washers to the UPPER holes. 3. Attach two blade bolts WITH washers to the LOWER holes as shown. 4. Tighten all these bolts completely to secure the blade into place. 5. Repeat for the remaining blades. Blade Bolt Blade Blade Bolt with Washer Light Installation 1. Remove the bolts from the bottom of the fan motor assembly. 2.
4. Position the light’s mounting plate against the motor, aligning their holes. 5. Replace and tighten the removed bolts to secure the LED light kit into place. 6. Fit the shade onto the LED light kit, rotating until it sits well on the tabs of the light plate. Ensure the shade is firmly connected to avoid loosening during use.
Remote Control Operation If needed, install the remote control holder onto a wall or any other suitable flat surface using appropriate fasteners. For wood or other thinner and weaker surfaces, use the provided steel screws and plastic anchors. For reinforced concrete or similar surfaces, use anchor bolts for best results. Key Function Turns the fan off When pressed, starts the fan in preset mode, automatically upshifting or downshifting the speed level in response to changes in the ambient temperature.
Troubleshooting Potential Problems Common Solutions Check fuses and/or circuit breakers and reset if needed. Cut off power to the fan and check its internal electrical connections. Fan blades don't rotate Replace the remote control’s batteries. Check that the fan cover is correctly placed and no fasteners interfere with the movement of the blades. Contact customer service to replace a faulty remote control. Check that all fasteners are well tightened.
Contact Us Thank you for choosing our products! If you have any questions or comments, contact us at contact@b2ccspro.com and we'll resolve your issue ASAP! For a .pdf copy of the latest version of these instructions, use the appropriate app on your smartphone to scan the QR code to the right.
C F N - 1 3 1 0 - B K C F N - 1 3 1 0 - N I C F N - 1 3 1 0 - O Z Rev. 19 Sept.
