MerryIoT Motion Detection Reference Manual MS10-915 MS10-868 Model Name: MS10 BQW_02_0033.
Table of Content 1. Description 1 2. Specifications 2 2.1 Mechanical ....................................................... 2 2.1.1 Sensor ................................................... 2 2.2 Environmental.................................................. 2 2.3 Power ............................................................... 2 2.4 Radio ................................................................ 2 2.5 User Interface .................................................. 2 2.
2. Specifications 2.1 Mechanical 2.1.1 Sensor Length x Width x Height 25mm x 70mm x 70mm Weight 62g without battery 96g with battery Dual Passive Infrared detectors Fresnel Lens with 123° horizontal & 93° vertical view Tamper detection Temperature/Humidity Maximum detect range 7M Sensor 2.2 Environmental 2.3 Power Temperature 0°C to +50°C IP Rating IP 40 equivalent 2.
3. Operation 3.1 Installation Mode Users need to press the button over 5 seconds to activate operation into installation mode. When the Sensor tries to join the network, it will keep blinking for 3 seconds. Once the sensor joins the network, the LED will keep on for 3 seconds and send an uplink. Users can press the button for over 5 seconds to try to join the network again. The device will send uplink three times with fw version when the device joined successfully. 3.
4.1.2 Payload Port 122 Payload Length 9 bytes Bytes 0 1 2 3 Field Status Battery Temp RH Status Battery 4 5 6 Time 7 8 Count Sensors status Bit [0] 1 – occupied, 0 – free Bit [1] 1 – Button pressed, 0 - Button released Bit [2] 1 – Tamper detected, 0 - No tamper detected Bits [7:3] RFU Battery level Bits [3:0] unsigned value ν, range 0 – 15; battery voltage in V = (21 + ν) ÷ 10.
5. Battery 5.1 Replacement Use Alkaline battery (AA) only. Remove the battery cover and replace the batteries. (cross-slot screwdriver required) 5.2 Cautions CAUTION: Disposal of a battery (or battery pack) into a fire or a hot oven, or mechanically crushing or cutting of a battery (or battery pack) can result in an EXPLOSION! Leaving a battery (or battery pack) in an extremely high temperature surrounding environment can result in an EXPLOSION or leakage of flammable liquid or gas.
6. Label format information 6.1 Device back label 6.1.1 All QR code SN:MS10915XXXXXX Model:MS10 FCC ID:2AAS9MS10 IC:26296-MS10 6.1.2 Series Number 6.1.3 Model Name 6.1.4 FCC ID 6.1.5 IC ID 6.1.1 All QR code URN:LW:D0: 0016160000000001:0016160000XXXXXX:01632002 The total maximum resulting character sentence is 48 alphanumeric characters long. 6.1.1.1 JoinEUI 900MHz: 0016160000000001. (US) 800MHz: 0016160000000002. (EU) Uses a hexadecimal representation resulting in 16 characters. 6.1.1.
6.1.2 Serial Number SN: MS10915XXXXXX Not including in QR code. 6.1.3 Model Name MODEL: MS10. Fixed code, not including in QR code. 6.1.4 FCC ID 2AAS9MS10 6.1.5 IC ID 26296-MS10 6.1.6 Caution! For more information please refer to chapter 5.2. and 10. 6.2 Packaging label GS1 DataMatrix The GS1 Application Identifier (21) indicates that the GS1 Application Identifier data field contains a serial number. The GS1 Application Identifier (92) assigned to the company’s internal information is DevEUI.
7. Important Product & Safety Instructions For the most current and more detailed information about Browan features and settings as well as safety instructions, please download the user manual for the products online at www.browan.com before the use of any Browan products or services. Certain sensors contain magnets. Keep away from ALL Children! Do not put it in your nose or mouth. Swallowed magnets can stick to intestines causing serious injury or death.
8. Warnings Do not place naked flame sources, such as lighted candles, on or near the equipment. Observe the plus (+) and minus (-) marks on the battery and equipment and ensure correct use. The battery shall not be exposed to excessive heat such as sunshine, fire, or the like. Do not use any which is not designed for use with the product. Do not dismantle, open or shred battery packs or cells. Do not mix cells of different manufacture, capacity, size, or type within a device.
10. Cautions CAUTION: Disposal of a battery (or battery pack) into a fire or a hot oven, or mechanically crushing or cutting of a battery (or battery pack) can result in an EXPLOSION! Leaving a battery (or battery pack) in an extremely high temperature surrounding environment can result in an EXPLOSION or leakage of flammable liquid or gas. A battery (or battery pack) subjected to extremely low air pressure may also result in an EXPLOSION or leakage of flammable liquid or gas.
11. Regulatory Hereby, Browan Communications Inc. declares that the radio equipment for Browan products complies with Directive 2014/53/EU. This device complies with Part 15 of the FCC Rules and RSS Standards of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Radiation Exposure Statement: The product complies with the US portable RF exposure limit set forth for an uncontrolled environment and is safe for intended operation as described in this manual. Further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such a function is available. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 11.
12. Configuration Downlink Command Note: Only For PIR Parameters Settings Port 102 Payload Length 5 bytes *Note: Configuration Down-link Command should consider the duty cycle. 12.1 Payload Bytes 0 Field Cmd Cmd Command Bit [7:0] Config 1 2 3 4 Config 0x01 – Set configuration, other values – RFU PIR Sensor Configuration Bits [4:0] RFU Bit [5] 0 – use band-pass filter, 1 – use low-pass filter.
Payload Content Command content Ex: 01000e02100 01 00e02100 => PIR parameter : 0x0021e000 Example: =>Room Occupied: 0100e02100 => Desk Occupied:(<=60cm) 0100148101 BROWAN COMMUNICATIONS All rights reserved 14
12.2 For Sensor Settings 12.2.1 Payload Port 204 Bytes 0 1~4 Field Cmd Config Cmd Command 1 byte Bit [7:0] 0x00 – Set keepalive interval in sec. default value : 3600 sec value range: 15~65535 0x02 – Set occupied interval in sec. default value : 600 sec value range: 0~65535 0x03 – Set free detection time in min. default value: 5 min value range: 0~255 0x04 - Set trigger count in the occupied status. default value : 0 value range: 0~65535 0x05 - Set PIR parameters. default value: please see 12.
Config Configuration (0~4 bytes ) See the table as follows: Cmd Command Description Config Length 0x00 Get Sensor Configuration (Only for unconfirmed downlink) *Note: little-endian format. 0 bytes 0x00 Set keepalive interval in sec *Note: little-endian format. 2 bytes 0x02 Occupied interval in sec *Note: little-endian format. 2 bytes 0x03 Free detection time in min 1 byte 0x04 Trigger Count in the occupied status *Note: little-endian format. 2 bytes 0x05 PIR Parameters (see 5.
12.3 Response Content (Only for unconfirmed downlink) Port 204 Payload Length 18 bytes Payload Content Response content Ex: 00100e 025802 0305 040000 0500e02100 0600 00 100e => Reporting interval : 0x0e10 -> 3600 sec 02 5802 => Occupied override : 0x0258 -> 600 sec 03 05 => Free detection time : 0x05 -> 5 min 04 0000 => Trigger Count in the occupied status 05 00e02100 => PIR parameter : 0x0021e000 06 00 => Disable tamper detection 12.
