Instruction Manual
netLiNKControls.com - 214.net.LiNK - Made in USA
Before aempng to Install the netLiNK
TM
Controls System, read these
instrucons carefully. Failure to do so may result in damage or malfuncon
to the system and will immediately void the warranty. Do Not Wire Hot!
netLiNK Controls, a Texas limited partnership (hereinaer the “Manufacturer”) sole and exclusive warranty regarding the
netLiNK Control Device (brands manufactured by netLiNK Controls hereinaer the “Control Device”) is that such Control
Device shall be free of defects in materials and workmanship at the date of invoice and shipment from the Manufacturer’s
dock, and for a period of two (2) years.
The Manufacturer’s sole obligaon under this warranty is to repair or replace the Control Device if such Control Device does
not funcon properly due to any component which proves to be defecve as a result of defecve materials or workmanship
of the Manufacturer; provided, however, that said malfuncon was not caused by: (i) lightning or other natural forces; (ii)
units not installed, operated, or maintained in accordance with instrucons provided, applicable local codes, ordinances, or
accepted trade pracces; (iii) failures resulng from abuse, misuse, accident, or negligence; (iv) units repaired, opened
and/or modified without prior authorizaon from the Manufacturer; or (v) any connected electrical malfuncon through
other acts or omissions of any end-user, distributer, contractor, or ESCO Customer (hereinaer the “Customer”).
To obtain warranty service, the Customer shall assume all responsibility and expense for removal, reinstallaon, and round
trip freight. Any item to be repaired or replaced under this warranty must be returned to the Manufacturer, or such place
as designated by the Manufacturer. Customer must contact the Manufacturer’s Customer Service prior to returning any
Control Device of the Manufacturer. Call 214.netLiNK (638-5465) or email support@netlinkcontrols.com for a Return
Material Authorizaon (RMA) number for any warranty claim.
LiNK Contro
ls
,aTexas
li
mited partners
hi
p
(h
ereina
e
r
th
e
“M
an
uf
acture
r”
)
so
le
and exc
lu
sive warranty regarding
t
netlink controls warranty
NOTE: If the light fixtures are not brand new, completely installed, and fully funconal you must ensure all lamps and
ballasts/drivers are in good working condion, and no electrical problems are present. If any lamps/fixtures are out, note
them on the site map and report them to netLiNK Controls before proceeding. It is recommended that a complete audit of
the exisng site lighng electrical system is done before installing netLiNK. The netLiNK Controls System must only be
installed on a completely operaonal system and by a qualified installer.
WARNING: The Base Staon and Wireless Nodes must be installed and wired in accordance with the Naonal Electrical
Code (NEC), all applicable Federal, State, and Local electrical codes as well as the specific U.L. safety standards for the
intended locaon/applicaon. A proper NEC ground must be aached to all terminal blocks, if conduit ground is not
sufficient or the warranty may be void.
CAUTION: These instrucons are only to be used as a guideline. Installaon may vary for different fixtures/devices and
applicaons. Please direct any quesons to netLiNK Controls Support.
INSTRUCTION TO THE USER: This equipment has been tested and found to comply with the limits for a class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful
interference in a residenal installaon. This equipment generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However,
there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful
interference to radio or television recepon, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separaon between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
To sasfy RF exposure requirements, this device and its antennas must operate with a separaon distance of at least 20 cm
from all persons and must not be co-located or operang in conjuncon with any other antenna or transmier.
In order to maintain compliance with FCC regulaons, shielded cables must be used with this equipment. Operaon with
non-approved equipment or unshielded cables is likely to result in interference to radio and TV recepon. The user is
cauoned that changes and modificaons made to the equipment without the approval of manufacturer could void the
user's authority to operate this equipment.