Designed for operating in USA & Canada only. When this product is used in areas other than the USA & Canada, we cannot guarantee the product quality and performance. Model Modèle Modelo WH 18DBFL2 Cordless Impact Driver Marteau à choc sans fil Atornillador de impacto inalámbrico SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL WARNING IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury! This manual contains important information about product safety.
English IMPORTANT SAFETY INFORMATION Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this power tool. Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety procedures.
English 3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection.
English – WARNING – To reduce the risk of injury, user must read instruction manual. SPECIFIC SAFETY RULES AND SYMBOLS 1. Hold power tools by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. 2. ALWAYS wear ear protectors when using the tool for extended periods.
English IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE CORDLESS IMPACT DRIVER WARNING Death or serious bodily injury could result from improper or unsafe use of the cordless impact driver. To avoid these risks, follow these basic safety instructions: 1. NEVER use this impact driver handle for any application other than those in this manual. 2. NEVER place hands or other body parts near the drill bit or chuck during operation. Hold the impact driver by its handle only. 3.
English 8. Do not operate battery charger with damaged cord or plug-replace them immediately. 9. Do not operate battery charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. 10. Do not disassemble battery charger; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire. 11.
English 5. Do not connect directly to an electrical outlets or car cigarette lighter sockets. 6. Do not use the battery for a purpose other than those specified. 7. If the battery charging fails to complete even when a specified recharging time has elapsed, immediately stop further recharging. 8. Do not put or subject the battery to high temperatures or high pressure such as into a microwave oven, dryer, or high pressure container. 9. Keep away from fire immediately when leakage or foul odor are detected.
English FUNCTIONAL DESCRIPTION NOTE The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety instructions contained in this manual. Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own power tool. NAME OF PARTS 1.
English 3. Battery Charger Cord Pilot lamp Body Pilot lamp Nameplate Cord Guide rail Guide rail Nameplate Fig. 4 SPECIFICATIONS 1.
English ASSEMBLY AND OPERATION APPLICATIONS ○ Driving and removing of machine screws, wood screws, tapping screws, etc. 1. Insert the plug of battery charger into the receptacle. When the plug of battery charger has been inserted into the receptacle, pilot lamp will blink in red. (At 1-second intervals) REMOVAL AND INSTALLATION METHOD OF BATTERY WARNING Do not use the electrical cord if damaged. Have it repaired immediately. 1.
English Table 2 Indications of the pilot lamp Pilot lamp (red) Lights for 0.5 seconds. Does not light for 0.5 seconds. (off for 0.5 seconds) Before charging Blinks While charging Lights Charging complete Blinks Lights for 0.5 seconds. Does not light for 0.5 seconds. (off for 0.5 seconds) Overheat standby Blinks Lights for 1 second. Does not light for 0.5 seconds. (off for 0.5 seconds) Lights continuously Lights for 0.1 seconds. Does not light for Flickers 0.1 seconds. (off for 0.
English (2) Avoid recharging at high temperatures. A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while. CAUTION ● When the battery charger has been continuosly used, the battery charger will be heated, thus constituting the cause of the failures.
English 6. Using the hook (for models with attached hook) The hook is used to hang up the power tool to your waist belt while working. CAUTION ● When using the hook, hang up the power tool firmly not to drop accidentally. If the power tool is dropped, it may lead to an accident. ● When electing to carry the tool hooked to your hip belt, make sure to detach the tool bit and side handle. Failure to do so may result in unexpected injury. ● Install securely the hook.
English 8. Remaining battery indicator You can check the battery’s remaining capacity by pressing the remaining battery indicator switch to light the indicator lamp. (Fig. 12, Table 7) The indicator will shut off approximately 3 seconds after the remaining battery indicator switch is pressed. It is best to use the remaining battery indicator as a guide since there are slight differences such as ambient temperature and the condition of the battery.
English 10. Tightening and loosening screws Install the bit that matches the screw, line up the bit in the grooves of the head of the screw, then tighten it. Push the impact driver just enough to keep the bit fitting the head of the screw. CAUTION ● Applying the impact driver for too long tightens the screw too much and can break it. ● Tightening a screw with the impact driver at an angle to that screw can damage the head of the screw and the proper force will not be transmitted to the screw.
English 5. Holding the tool Hold the tool firmly with both hands. In this case hold the tool in line with the screw or bolt. It is not necessary to push the tool very hard. Hold the tool with a force just sufficient to counteract the impact force. 6. Confirm the tightening torque The following factors contribute to a reduction of the tightening torque. So confirm the actual tightening torque needed by screwing up some bolts before the job with a hand torque wrench.
English 7. Storage Storing in a place below 104°F (40°C) and out of the reach of children. NOTE Storing lithium-ion batteries Make sure the lithium-ion batteries have been fully charged before storing them. Prolonged storage (3 months or more) of batteries with a low charge may result in performance deterioration, significantly reducing battery usage time or rendering the batteries incapable of holding a charge.
English TROUBLESHOOTING GUIDE WARNING ● To avoid injury from an accidental start, turn the switch OFF and remove the plug from the power source or remove the battery from the main body before making any adjustments. ● All electrical or mechanical repairs should be done only by qualified service technicians. Contact metabo HPT Authorized Service Center. Problem Tool doesn’t run Possible Cause No remaining battery power The trigger switch was held down while the battery was inserted.
English ACCESSORIES WARNING ALWAYS use Only authorized metabo HPT replacement parts and accessories. Never use replacement parts or accessories which are not intended for use with this tool. Contact metabo HPT if you are not sure whether it is safe to use a particular replacement part or accessory with your tool. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage.
English 2 1 3 WH18DBFL2 (LEG) 1 Battery (BSL1815) ................................................................................. 1 2 Battery Charger (UC18YKSL) ............................................................... 1 3 Battery cover (Code No. 329897) ......................................................... 1 1 2 4 WH18DBFL2 (2LMRX) 1 2 3 4 5 3 5 Battery (BSL1830C) .............................................................................. 1 Battery (BSL36A18) ......................
English OPTIONAL ACCESSORIES.....sold separately 1. Battery (BSL1815 / BSL1830C / BSL36A18) 2. Hook 3. Phillips bit 2"(50mm) Bit No. No.2 No.3 Code No. 992671 992672 4. Hexagonal socket Engraved characters L B Code No.
Français INFORMATIONS IMPORTANTES DE SÉCURITÉ Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions de fonctionnement dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé. La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé proviennent d’un non respect des règles ou précautions de base de sécurité.
Français Maintenir le cordon loin de la chaleur, de l'huile, des bords pointus ou des pièces mobiles. Les cordons endommagés ou usés augmentent les risques de choc électrique. e) En cas d'utilisation d'un outil électrique à l'extérieur, utiliser un cordon de rallonge adapté à un usage extérieur. L'utilisation d'un cordon adapté à l'usage extérieur réduit les risques de choc électrique.
Français Un chargeur inadéquat pour le type de batterie peut entraîner un risque d’incendie en cas d’utilisation avec une autre batterie. b) Utiliser les outils électriques uniquement avec les batteries spécifiées. L’utilisation d’autres batteries peut entraîner un risque de blessures et d’incendie.
Français 10. Manipuler l’outil correctement Utiliser l’outil de la façon indiquée dans ce mode d’emploi. Ne pas laisser tomber ou lancer l’outil. NE JAMAIS permettre que l’outil soit utilisé par des enfants, des personnes non familiarisées avec son fonctionnement ou un personnel non autorisé. 11. Maintenir toutes les vis, tous les boulons et les couvercles fermement en place. Maintenir toutes les vis, tous les boulons et les couvercles fermement montés. Vérifier leurs conditions périodiquement. 12.
Français 4. L’utilisation d’un accessoire non recommandé ou non vendu par le fabricant du chargeur de batterie risque de provoquer un feu, une décharge électrique ou des blessures. 5. Pour réduire tout risque de dommage de la fiche et du cordon électrique, débrancher le cordon du chargeur en tirant sur la fiche. 6. Vérifier que le cordon est placé de façon que personne ne puisse marcher dessus, se prendre les pieds dedans, ni l’endommager ou le soumettre à des contraintes. 7.
Français 4. NE JAMAIS insérer d’objets dans les ouïes d’aération du chargeur. Il pourrait en résulter un choc électrique ou des dommages du chargeur. 5. NE JAMAIS effectuer la recharge à l’extérieur. Eloigner la batterie des rayons directs du soleil et utiliser exclusivement dans des endroits à faible humidité et bien aérés. 6. NE JAMAIS effectuer la recharge si la température est inférieure à 32°F (0°C) ou supérieure à 104°F (40°C). 7. NE JAMAIS raccorder deux chargeurs de batterie ensemble. 8.
Français PRECAUTION 1. En cas de projection dans les yeux de liquide ayant fuit de la batterie, ne vous frottez pas les yeux, rincezles à l’eau claire et contactez immédiatement un médecin. En l’absence de traitement, le liquide peut détériorer l’oeil. 2. En cas de projection de liquide ayant fuit de la batterie sur votre peau ou vos vêtements, rincez immédiatement ces derniers à l’eau claire (au robinet). Le liquide peut provoquer une irritation de la peau. 3.
Français DESCRIPTION FONCTIONNELLE REMARQUE Les informations contenues dans ce mode d’emploi sont conçues pour assister l’utilisateur dans une utilisation sans danger et un entretien de l’outil motorisé. NE JAMAIS utiliser ni entreprendre une révision de l’outil sans avoir d’abord lu et compris toutes les instructions de sécurité contenues dans ce manuel. Certaines illustrations dans ce mode d’emploi peuvent montrer des détails ou des accessoires différents de ceux de l’outil motorisé utilisé.
Français 3. Chargeur de batterie Lampe Cordon témoin Cordon Corps Lampe témoin Plaque signalétique Rail guide Rail guide Plaque signalétique Fig. 4 SPECIFICATIONS 1.
Français ASSEMBLAGE ET FONCTIONNEMENT UTILISATIONS ○ Enfoncement et extraction de vis mécaniques, vis de bois, vis de taraudage, etc. 1. Insérez la fiche du chargeur de batterie dans la prise. Une fois que la fiche du chargeur de batterie est branchée dans la prise, la lampe témoin clignote rouge. (À intervalles de 1 seconde) AVERTISSEMENT MÉTHODE DE RETRAIT ET D’INSTALLATION DE LA BATTERIE 1.
Français Tableau 2 Explications de la lampe témoin S’allume pendant 0.5 seconde. Ne s’allume pas pendant 0.5 seconde. (Eteint Clignote pendant 0.5 seconde) Avant la recharge Pendant la recharge Lampe témoin (rouge) S’allume S’allume sans interruption S’allume pendant 0.5 seconde. Ne s’allume pas pendant 0.5 seconde. (Eteint Clignote pendant 0.5 seconde) Recharge terminée Batterie en surchauffe. S’allume pendant 1 seconde. Ne s’allume Chargement impossible (le pas pendant 0.5 seconde.
Français Comment prolonger la durée de vie des batteries (1) Recharger les batteries avant qu’elles ne soient complètement épuisées. Quand la puissance de l’outil utilisé faiblit, l’éteindre et recharger la batterie. Si l’outil continue d’être utilisé jusqu’à épuisement du courant électrique, la batterie risque d’être endommagée et sa durée de vie se raccourcira. (2) Eviter d’effectuer la recharge sous des températures élevées. Une batterie est toujours chaude immédiatement après son utilisation.
Français 5. Fonctionnement de l’interrupteur ○ Quand on tire sur la gâchette de l’interrupteur, l’outil tourne. Quand on relâche la gâchette, l’outil s’arrête. ○ La vitesse de rotation peut être contrôlée en faisant varier la force avec laquelle on appuie sur la gâchette. Quand on appuie légèrement sur la gâchette, la vitesse est lente, et elle augmente quand on appuie plus fort. ○ Lorsque le déclencheur est libéré, le frein arrête immédiatement l’outil. (2) Remplacer le crochet et serrer les vis.
Français Panneau d’affichage Déclencheur Témoin lumineux de puissance batterie résiduelle Fig. 11 REMARQUE Ne pas faire subir de choc violent au panneau d’affichage ou l’endommager. Cela peut provoquer des défaillances. 8. Témoin de batterie résiduelle Vous pouvez vérifier la capacité résiduelle de la batterie en appuyant sur le commutateur d’indicateur de batterie résiduelle pour allumer le témoin de l’indicateur. (Fig.
Français 9. Comment utiliser la DEL d’éclairage Lorsque le commutateur est activé, la DEL illumine automatiquement la pointe de l’outil. (Fig. 13) La DEL lumineuse s’éteint automatiquement 10 secondes après avoir relâché le commutateur. Déclencheur Fig. 13 PRECAUTION ● N’exposez pas vos yeux directement à la lampe en la regardant. Une exposition continue de vos yeux à la lampe pourrait les blesser.
Français Fonction de protection Protection surcharge Protection température Tableau 8 Affichage du témoin DEL Marche 0.1 seconde/Arrêt 0.1 seconde Action corrective Éliminer la cause de la surcharge. Marche 0.5 seconde/Arrêt 0.5 seconde Laisser l'outil et la batterie refroidir complètement. PRECAUTIONS D'UTILISATION 1.
Français ENTRETIEN ET INSPECTION PRECAUTION Sortir la batterie avant toute opération d’inspection ou d’entretien. 1. Vérifier l’état de la mèche. Les mèches doivent être vérifiées régulièrement. Si elles sont usées ou cassées, elles risquent de glisser ou de réduire le rendement du moteur et de le brûler. Remplacer les mèches usées par des neuves. PRECAUTION Si l’on utilise une mèche dont la pointe est usée ou cassée, elle sera dangereuse car elle risque de glisser. La remplacer par une neuve. 2.
Français Avis important sur les batteries pour outils électriques sans fil metabo HPT Toujours utiliser une de nos batteries originales spécifiées. Nous ne saurions garantir la sécurité et la performance de notre outil électrique sans fil s’il est utilisé avec une batterie autre que celle que nous avons spécifié, ou encore si la batterie est démontée et modifiée (par exemple, le démontage et remplacement des cellules ou autres composants internes).
Français ACCESSOIRES AVERTISSEMENT TOUJOURS utiliser UNIQUEMENT des pièces de rechange et des accessoires metabo HPT. Ne jamais utiliser de pièce de rechange ou d’accessoires qui ne sont pas prévus pour être utilissl avec cet outil. En cas de doute, contacter metabo HPT pour savoir si une pièce de rechange ou un accessoire particulier peuvent être utilisés en toute sécurité avec votre outil.
Français 2 1 3 WH18DBFL2 (LEG) 1 Batterie (BSL1815) ................................................................................ 1 2 Chargeur de batterie (UC18YKSL) ........................................................ 1 3 Couvercle de batterie (N° de code 329897) ......................................... 1 1 2 4 WH18DBFL2 (2LMRX) 1 2 3 4 5 3 5 Batterie (BSL1830C) ............................................................................. 1 Batterie (BSL36A18) ............................
Français ACCESSOIRES EN OPTION.....vendus séparément 1. Batterie (BSL1815 / BSL1830C / BSL36A18) 2. Crochet 3. Mèche Phillips 2"(50mm) N° de mèche N° 2 N° 3 N° de code 992671 992672 4.
Español INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD Antes de utilizar o de realizar cualquier trabajo de mantenimiento de esta herramienta eléctrica, lea y comprenda todas las precauciones de seguridad, advertencias e instrucciones de funcionamiento de este Manual de instrucciones. La mayoría de los accidentes producidos en la operación y el mantenimiento de una herramienta eléctrica se deben a la falta de observación de las normas o precauciones de seguridad.
Español Mantenga el cable alejado del calor, del aceite, de bordes afilados o piezas móviles. Los cables dañados o enredados aumentan el riesgo de descarga eléctrica. e) Cuando utilice una herramienta eléctrica al aire libre, utilice un cable prolongador adecuado para utilizarse al aire libre. La utilización de un cable adecuado para usarse al aire libre reduce el riesgo de descarga eléctrica.
Español La utilización de la herramienta eléctrica para operaciones diferentes a pretendidas podría dar lugar a una situación peligrosa. 5) Utilización y cuidado de las herramientas a pilas a) Recargue sólo con el cargador especificado por el fabricante. Un cargador que es apto para un tipo de paquete de pilas podría crear un riesgo de incendio cuando se utiliza con otro paquete de pilas. b) Utilice herramientas eléctricas sólo con paquetes de pilas específicamente diseñados.
Español 10. Maneje correctamente la herramienta. Maneje la herramienta de acuerdo con las instrucciones ofrecidas aquí. No deje caer ni tire la herramienta. NO permita NUNCA que los niños ni otras personas no autorizadas ni familiarizadas con la operación de la herramienta utilicen ésta. 11. Mantenga todos los tornillos, pernos, y cubiertas firmemente fijados en su lugar. Mantenga todos los tornillos, pernos, y cubiertas firmemente montados. Compruebe periódicamente su condición. 12.
Español INSTRUCCIONES IMPORTANTES DE SEGURIDAD PARA EL CARGADOR DE BATERÍAS ADVERTENCIA La utilización inadecuada del Atornillador de impacto inalámbrico puede resultar en lesiones serias o en la muerte. Para evitar estos riesgos, siga las instrucciones de seguridad ofrecidas a continuación. LEA TODAS LAS INSTRUCCIONES 1. Este manual contiene instrucciones importantes de seguridad para el cargador de baterías modelo UC18YKSL / UC18YFSL. 2.
Español INSTRUCCIONES IMPORTANTES DE SEGURIDAD PARA LA BATERÍA Y EL CARGADOR DE BATERÍAS Usted deberá cargar la batería antes de utilizar el atornilladores de percusion inalámbrico. Antes de utilizar el cargador de baterías modelo UC18YKSL / UC18YFSL, cerciórese de leer todas las instrucciones y precauciones del mismo, de la batería, y de este manual. PRECAUCIÓN ¡UTILICE SOLAMENTE BATERÍA metabo HPT DEL TIPO DE LAS SERIES BSL18 Y BSL36A18.
Español 7. Si la carga de la batería no finaliza incluso cuando ha transcurrido un determinado tiempo de recarga, detenga inmediatamente la recarga. 8. No coloque o exponga la batería a temperaturas elevadas o alta presión como en un microondas, una secadora o un contenedor de gran presión. 9. Aléjela del fuego inmediatamente cuando se detecte una fuga o un olor raro. 10. No la utilice en un lugar donde se genere gran electricidad estática. 11.
Español DESCRIPCIÓN FUNCIONAL NOTA La información contenida en este Manual de instrucciones ha sido diseñada para ayudarle a utilizar con seguridad y mantener esta herramienta eléctrica. NUNCA haga funcionar ni efectúe el mantenimiento de la herramienta antes de leer y comprender todas las instrucciones de seguridad contenidas en este manual. Algunas ilustraciones de este Manual de Instrucciones pueden mostrar detalles o accesorios diferentes a los de la propia herramienta eléctrica. NOMENCLATURA 1.
Español 3. Cargador de baterías Lámpara piloto Cable Cuerpo Lámpara piloto Placa de características Cable Riel de guía Riel de guía Placa de características Fig. 4 ESPECIFICACIONES 1.
Español MONTAJE Y OPERACIÓN APLICACIONES ○ Atornillamiento y desatornillamiento de tornillos para metales, tornillos para madera, tornillos que no necesitan abrir antes su agujero, etc. 1. Inserte el conector del cargador de baterías en el receptáculo. Cuando el conector del cargador de baterías haya sido insertado en el receptáculo, la lámpara piloto parpadeará en rojo (en intervalos de 1 segundo). ADVERTENCIA MÉTODO DE EXTRACCIÓN E INSTALACIÓN DE LA BATERÍA 1.
Español Tabla 2 Indicaciones de la lámpara indicadora Se encenderá durante 0.5 segundos. No se encenderá durante 0.5 segundos. Parpadeo (Apagada durante 0.5 segundos) Antes de la carga Durante la carga Lámpara piloto (rojo) Iluminación Iluminación permanente Parpadeo Se encenderá durante 0.5 segundos. No se encenderá durante 0.5 segundos. (Apagada durante 0.5 segundos) Espera por recalentamiento Parpadeo Se encenderá durante 1 segundo. No se encenderá durante 0.5 segundos. (Apagada durante 0.
Español (2) Evite realizar la recarga a altas temperaturas. Una batería se calentará inmediatamente después de haberla utilizado. Si recargase tal batería inmediatamente después de haberla utilizado, su substancia química interna se deterioraría, y la duración útil de la batería se acortaría. Deje la batería y recárguela después de que se haya enfriado durante cierto tiempo. PRECAUCIÓN ● Si utiliza continuamente el cargador de baterías, éste se calentará, lo que puede causar averías.
Español 6. Uso del gancho (para modelos con gancho adjunto) El gancho se usa para colgarse la herramienta con alimentación eléctrica del cinturón mientras se trabaja. PRECAUCIÓN ● Cuando se utiliza el gancho, se debe sujetar la herramienta con firmeza para que no se caiga por accidente. Al caer, puede provocar un accidente. ● Cuando elija transportar la herramienta enganchada a su cinturón, asegúrese de desensamblar el taladro de la herramienta y el asa lateral.
Español 8. Indicador de batería restante Puede comprobar la capacidad restante de la batería presionando el interruptor del indicador de batería restante para encender la lámpara indicadora. (Fig. 12, Tabla 7) El indicador se apaga aproximadamente 3 segundos después de pulsar el interruptor del indicador de batería restante. Se recomienda utilizar el indicador de batería restante como guía dado que hay ligeras diferencias tales como la temperatura ambiente y el estado de la batería.
Español 10. Apretado y aflojado de pernos (Llave de impacto) Instale la punta de destornillador adecuada al tornillo, alinéela con las ranuras de la cabeza del mismo, y después apriételo. Empuje el atornillador de percusión lo suficientemente como para que la punta de destornillador encaje en la cabeza del tornillo. PRECAUCIÓN ● Si aplica demasiado tiempo el atornillador de impacto sobre el tornillo, éste se apretará demasiado y se romperá.
Español 4. Tensiónde apriete apropiada para los pernos y tuercas La tensión de apriete óptima para pernos y tuercas difiere según su material y tamaño. Una tensión de apriete excesiva para un perno pequeño podría deformarlo o romperlo. La tensión de apriete aumenta proporcionalmente al teimpo de operación. Utilice la indicación de la escala y el tiempo de operación adecuados a cada perno. 5. Sujetar la herramienta Sujete la herramienta con firmeza con ambas manos.
Español MANTENIMIENTO E INSPECCIÓN PRECAUCIÓN Extraiga la batería antes de realizar cualquier trabajo de inspección o de mantenimiento. 1. Comprobación de las condiciones de la broca. Las brocas deberán comprobarse regularmente. Si una broca está desgastada o rota, puede patinar o reducir la eficacia del motor, o hacer que se queme. Reemplace las brocas gastadas por otras nuevas. PRECAUCIÓN Si utiliza una broca de destornillador con su punta desgastada o rota, puede resultar peligroso, porque patinará.
Español MODIFICACIONES: metabo HPT Power Tools introduce constantemente mejoras y modificaciones para incorporar los últimos avances tecnológicos. Por consiguiente, algunas partes pueden ser modificadas sin previo aviso. Aviso importante sobre las pilas de las herramientas inalámbricas de metabo HPT Utilice siempre una de nuestras pilas genuinas.
Español ACCESSORIOS ADVERTENCIA UTILICE únicamente repuestos y accesorios autorizados por metabo HPT. No utilice nunca repuestos o accesorios no previstos para usar con esta herramienta. Si tiene dudas en cuanto a la seguridad de usar determinado repuesto o accesorio junto con su herramienta, póngase en contacto con metabo HPT. La utilización de otros accesorios puede resultar peligrosa y causar lesiones o daños mecánicos.
Español 2 1 3 WH18DBFL2 (LEG) 1 Batería (BSL1815) ................................................................................. 1 2 Cargador de baterías (UC18YKSL) ....................................................... 1 3 Taps de batería (No de código 329897) ................................................ 1 1 2 4 WH18DBFL2 (2LMRX) 1 2 3 4 5 3 5 Batería (BSL1830C) .............................................................................. 1 Batería (BSL36A18).............................
Español ACCESORIOS OPCIONALES.....de venta por separado 1. Batería (BSL1815 / BSL1830C / BSL36A18) 2. Gancho 3. Broca Phillips 2"(50mm) No. de destornillador No.2 No.3 No. de código 992671 992672 4. Receptáculo hexagonal para tuercas y pernos Nombre de la pieza Caracteres grabados L B No.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● Lead from lead-based paints, ● Crystalline silica from bricks and cement and other masonry products, and ● Arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.