User Manual

ENGLISH en
17
Use only accessories that
are covered by at least 3.4
mm by the safety guard.
Before carrying out any modifications, remove
the battery pack from the machine and pull the
mains plug from the socket. The machine must be
switched off and the spindle must be at a standstill.
For reasons of safety, attach the parting guard
before performing parting work (see chapter
11. Accessories).
7.1 Locking the spindle
Press in the spindle locking button (5) only
when the spindle is stationary!
- Press in the spindle locking button (5) and turn the
spindle (4) by hand until you feel the spindle
locking button engage.
7.2 Placing the grinding wheel in position
See illustration C on page 2.
- Fit the support flange (3) on the spindle. The
flange should not turn on the spindle when prop-
erly attached.
- Place the grinding wheel on the support flange (3).
The grinding wheel must lay flat on the supporting
flange. The metal flange on the parting grinder
disc must lay flat on the support flange.
7.3 Securing/releasing the (tool-free) clamp-
ing nut (depending on features)
Only tighten the (tool-free) clamping nut (2)
manually.
For the machine to operate, the clip (1) must
always lie flat on
clamping nut (2) .
To secure the (tool-free) clamping nut (2):
Do not use the (tool-free) clamping nut if the
accessory has a clamping shank thicker than 6
mm
! In this case, use the clamping nut (18) with 2-
hole spanner (19).
- Lock the spindle (see chapter 7.1).
- Flip up the clip
(1) on the clamping nut.
- Fit the clamping nut (2) on the spindle (4). See
illustration D on page 2.
-
(1)Tighten the clamping nut on the clip manually
in a clockwise direction.
- Flip down the clip
(1) again .
To release the (tool-free) clamping nut (2) :
- Lock the spindle (see chapter 7.1).
- Flip up the clip
(1) on the clamping nut.
- Unscrew the clamping nut
(2) , turning it anticlock-
wise manually .
Note:
If the clamping nut is very tightly secured (2),
you can also use a 2-hole spanner to unscrew it.
7.4 Tightening/loosening the clamping nut
Securing the clamping nut (18):
The 2 sides of the clamping nut are different. Screw
the clamping nut onto the spindle as follows:
See illustration D on page 2.
- A) For thin grinding wheels:
The edge of the clamping nut (18) faces upwards
so that the thin grinding wheel can be attached
securely.
B) For thick grinding wheels:
The edge of the clamping nut (18) faces down-
wards so that the clamping nut can be attached
securely to the spindle.
- Lock the spindle. Turn the clamping nut (18)
clockwise using the 2-hole spanner (19) to
secure.
Releasing the clamping nut:
- Lock the spindle (see chapter 7.1). Turn the
clamping nut (18) anticlockwise using the 2-hole
spanner (19) to unscrew.
8.1 Switching On and Off
Always guide the machine with both hands.
Switch on first, then guide the
accessory
towards the workpiece.
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off, keep it away from dust
deposits. After switching off the machine, only place
it down when the motor has come to a standstill.
Avoid switching on the machine accidentally:
always switch it off when the battery pack is
removed from the machine.
Avoid inadvertent starts: always switch the
tool off when the plug is removed from the
mains socket or if there has been a power cut.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand in a
safe position and concentrate.
Machines with slide switch:
Switching on: Push the slide switch (8) forward.
For continuous activation, now tilt down-
wards until it engages.
Switching off: Press the rear end of the slide
switch (8) and release.
7. Attaching the grinding wheel
8. Use
0
I
8