User guide

ManualsBrandsMetal Sales ManualsFor HomeDelta Rib Manual

PDR-1

DELTA RIB

800.406.7387 (Corporate Ofce) • www.metalsales.us.com

Eave Detail ..........................................................PDR-9

Gutter Detail ........................................................PDR-9

Valley Detail ....................................................... PDR-10

Rake Detail ........................................................PDR-10

Rakewall with Counter Flashing Detail .............. PDR-11

Endwall with Counter Flashing Detail ................ PDR-11

Sculptured High Side Eave Detail .....................PDR-12

Ridge/Hip Detail.................................................PDR-12

Universal Ridge Detail .......................................PDR-13

Gravel Stop Detail .............................................PDR-13

Outside Corner Detail ........................................PDR-14

Inside Corner Detail ........................................... PDR-14

Jamb Detail........................................................PDR-15

Head Detail ........................................................ PDR-15

Base Detail ........................................................PDR-16

Notes .................................................................PDR-16

Table of ConTenTs

Product Page No.

Delta Rib Panel Prole ........................................PDR-2

Panel Overview ...................................................PDR-2

Eave (Direct Fasten)............................................PDR-3

Sculptured Gutter ................................................PDR-3

Sculptured Gutter End .........................................PDR-3

Universal Gutter/Downspout Strap ......................PDR-3

Downspout...........................................................PDR-3

95° Elbow ............................................................PDR-3

Downspout Bracket .............................................PDR-3

Gutter Hanger ...................................................... PDR-3

Sculptured Corner Box ........................................PDR-3

Sculptured Peak Box ...........................................PDR-3

Valley ...................................................................PDR-3

Sculptured Rake ..................................................PDR-3

Sculptured Rake End...........................................PDR-3

Pitch Break ..........................................................PDR-3

Sculptured High Side Eave..................................PDR-3

Counter Flashing .................................................PDR-4

Reglet Flashing....................................................PDR-4

20" Ridge/Hip Cover ............................................ PDR-4

Universal Ridge Cover.........................................PDR-4

Vented Ridge Cover ............................................PDR-4

Vent Drip .............................................................. PDR-4

Gravel Stop..........................................................PDR-4

Inside Corner .......................................................PDR-4

Outside Corner ....................................................PDR-4

1.5" Sill/Head ....................................................... PDR-4

1.5" Sill to Soft ...................................................PDR-4

1.25" Base ...........................................................PDR-4

Jamb .................................................................... PDR-4

Head Channel......................................................PDR-4

Head Jamb Cover................................................PDR-4

Cleat ....................................................................PDR-5

Delta Rib Closures...............................................PDR-5

Universal Closure ................................................PDR-5

Vent Material........................................................PDR-5

Tube Sealant .......................................................PDR-5

Tape Sealant........................................................PDR-5

Rubber Roof Jack ................................................ PDR-5

Retro Roof Jack ................................................... PDR-5

Rubber Roof Flashing Kit ....................................PDR-5

Touch-Up Paint .................................................... PDR-5

Continuous Ridge Vent ........................................ PDR-5

Louver with Screen .............................................. PDR-5

Section Properties and General Information .......PDR-6

Fastener Installation Technique ........................... PDR-7

Fastening Information .......................................... PDR-8

Condition of Substructure ....................................PDR-8

Panel Information

Flashing Proles

Accessory Proles

Design/Installation Considerations

Testing Information

Detail Conditions

Notes

Product Page No.

Summary of content (16 pages)

PAGE 1
DELTA RIB Table of Contents Product Page No. Product Page No. Panel Information Detail Conditions Delta Rib Panel Profile.........................................PDR-2 Panel Overview....................................................PDR-2 Eave Detail...........................................................PDR-9 Gutter Detail.........................................................PDR-9 Valley Detail........................................................PDR-10 Rake Detail........................
PAGE 2
DELTA RIB Panel Overview DELTA RIB PROFILE 24" Coverage 8" 13 /16" SLOPE The minimum recommended slope for any Delta Rib roofing panel is 3:12. Metal Sales recommends that in all roof applications sealant be used on sidelaps. SUBSTRATE Delta Rib is designed to be utilized over open structural framing, but can easily be used with a solid substrate. The recommended substrate is 5/8" plywood with a 30 pound felt moisture barrier.
PAGE 3
DELTA RIB Flashing Profiles EAVE (DIRECT FASTEN) SCULPTURED GUTTER SCULPTURED GUTTER END 1 /2" 11/2" 1 47/8" X* 5 C 31/2" X* 3 /2" 150° 51/2" 150° 3" /8" X* 3 /2" 1 1 105° 51/2" 105° 6" Hem Length 10'-2" - *Specify Slope Angle UNIVERSAL GUTTER/ DOWNSPOUT BRACKET 6" Length 10'-2", 20'-3" - *Specify Slope Angle DOWNSPOUT 6" x 4" 4" 6" Hem 950 ELBOW 6" x 4" 4" 6" C C 16" 11/2" DOWNSPOUT BRACKET Length 10'-2", 20'-3" (Also available 4" x 31/2") (Also available 4" x 31/2")
PAGE 4
DELTA RIB Flashing Profiles (cont.
PAGE 5
DELTA RIB Flashing Profiles (cont.) / Accessory Profiles CLEAT 21/2" C- Indicates color side of flashing. 135° C 1 /2" Length 10'-2" DELTA-RIB Accessory Profiles DELTA RIB CLOSURES UNIVERSAL CLOSURE VENT MATERIAL 33/8" Inside Closure /" 7 8 Outside Closure Polyethylene Foam TUBE SEALANT 4" 1" x 11/2" x 50' Polyethylene Foam 1" x 11/2" x 10' Polyethylene Foam TAPE SEALANT / " X / " X 50' Single Bead Butyl - Gray 3 8 10.3 oz.
PAGE 6
DELTA RIB Section Properties and Load Tables 24" Coverage 4" 8" C /16" 13 ALLOWABLE UNIFORM LIVE LOADS PSF (3 or More Equal Spans) SECTION PROPERTIES Ga. Width Yield (in.) KSI Weight PSF Top in Compression Bottom in Compression Ixx In4/ft Sxx In3/ft Ixx In4/ft Sxx In3/ft Inward (Gravity / Deflection) Load Outward Uplift (Stress) Load 2' 3' 4' 5' 6' 7' 2' 3' 4' 5' 6' 26 24" 80 0.80 0.0160 0.0275 0.0135 0.
PAGE 7
DELTA RIB Design / Installation Considerations FASTENER INSTALLATION TECHNIQUE USING NAILS: If nails are used as a fastening method, it is best to use a painted or galvanized steel ring shank nail with a flat neoprene washer. Nails should penetrate the wood support to a depth of at least 1/4”, but should not be to long as to protrude completely through the support. Nails must not be driven to tight. Overdriving may cause damage to washers and/or the steel sheet.
PAGE 8
DELTA RIB Design / Installation Considerations (cont.) FASTENING PATTERN Note: Fastening patterns should be checked to meet applicable loading conditions. 1 4 / "-14 x 7/8" Stitch Screw (1'-0" o.c.) Tape Sealant (roof only) #10 x 1" Woodscrew Typical Screw Fastening Pattern Typical Nail Fastening Pattern CONDITION OF SUBSTRUCTURE Whether over solid substrate or open structural framing, panel distortion may occur if not applied over properly aligned and uniform substructure.
PAGE 9
DELTA RIB Eave Detail 3:12 Slope Minimum Tape Sealant #12-14 x 11/2" SD (see below) Delta Rib Inside Closure Delta Rib Panel #12-14 x 11/2" SD (see below) Eave Tape Sealant 1 /4"-14 x 7/8" Stitch (every rib) Delta Rib Outside Closure Delta Rib Panel / "-14 x 7/8" Stitch Screw (1'-0" o.c.
PAGE 10
DELTA RIB Valley Detail 3:12 Slope Minimum Delta Rib Panel (bevel cut in field) Tape Sealant #12-14 x 11/2" SD (see below) Pro-Panel II Inside Closure Valley Plate Valley 3" Minimum CL / "-14 x 7/8" Stitch Screw (1'-0" o.c.) 1 4 #12-14 x 11/2" SD DELTA-RIB 3:12 Slope Minimum Tape Sealant (roof only) Rake Detail Delta Rib Screw Fastening Pattern Delta Rib Panel #12-14 x 11/2" SD 1 /4"-14 x 7/8" Stitch (1'-0" o.c.
PAGE 11
DELTA RIB 3:12 Slope Minimum DELTA-RIB 3:12 Slope Minimum Rakewall with Counter Flashing Detail Tube Sealant Fasteners (by others) Counter Flashing Rakewall 1 /4"-14 x 7/8" Stitch (1'-0" o.c.) Tape Sealant Delta Rib Panel Endwall with Counter Flashing Detail Tube Sealant Fasteners (by others) Counter Flashing Pitch Break #12-14 x 11/2" SD (see below) 1 /4"-14 x 7/8" Stitch (every rib) Tape Sealant Delta Rib Outside Closure Delta Rib Panel / "-14 x 7/8" Stitch Screw (1'-0" o.c.
PAGE 12
DELTA RIB Sculptured High Side Eave Detail Delta Rib Panel /4"-14 x 7/8" Stitch (every rib) Tape Sealant Delta Rib Outside Closure Tape Sealant Sculptured High Side Eave #12-14 x 11/2" SD (see below) 3:12 Slope Minimum 1 Tape Sealant 1 /4"-14 x 7/8" Stitch (every rib) Delta Rib Outside Closure Delta Rib Panel 1/4"-14 x 7/8" Stitch Screw (1'-0" o.c.
PAGE 13
DELTA RIB Universal Ridge Detail 3:12 Slope Minimum #12-14 x 11/2" SD (see below) Delta Rib Outside Closure 1 /4"-14 x 7/8" Stitch (every rib) Tape Sealant Universal Ridge Cover / "-14 x 7/8" Stitch Screw (1'-0" o.c.
PAGE 14
DELTA RIB Outside Corner Detail Outside Corner 1 /4"-14 x 7/8" Stitch (1'-0" o.c.) Tape Sealant Delta Rib Panel DELTA-RIB Inside Corner Detail Inside Corner 1 /4"-14 x 7/8" Stitch (1'-0" o.c.) Tape Sealant Delta Rib Panel PDR-14 © Metal Sales Manufacturing Corporation/ Subject to change without notice/ Effective Date 9/11 800.406.7387 (Corporate Office) • www.metalsales.us.
PAGE 15
DELTA RIB Jamb Detail Delta Rib Panel #12-14 x 11/2" SD (1'-0" o.c.) Delta Rib Panel Jamb Head/Jamb Cover DELTA-RIB Head Detail Delta Rib Panel #12-14 x 11/2" SD (see below) Delta Rib Inside Closure Tape Sealant Delta Rib Panel Head Channel Head/Jamb Cover / "-14 x 7/8" Stitch Screw (1'-0" o.c.) 1 4 #12-14 x 11/2" SD Tape Sealant (roof only) Delta Rib Screw Fastening Pattern © Metal Sales Manufacturing Corporation/ Subject to change without notice/ Effective Date 9/11 800.406.
PAGE 16
DELTA RIB Base Detail Delta Rib Panel Delta Rib Inside Closure Tape Sealant #12-14 x 11/2" SD (see below) 11/4" Base / "-14 x 7/8" Stitch Screw (1'-0" o.c.) 1 4 #12-14 x 11/2" SD Tape Sealant (roof only) Delta Rib Screw Fastening Pattern DELTA-RIB PDR-16 Notes © Metal Sales Manufacturing Corporation/ Subject to change without notice/ Effective Date 9/11 800.406.7387 (Corporate Office) • www.metalsales.us.