Installation Guide

ManualsBrandsMetalbest ManualsHVAC8" Inner Diameter - DSP Stove Pipe - Double Wall -36" Pipe Length

RM19896-1

SELKIRK CANADA CORPORASELKIRK CANADA CORPORA

SELKIRK CANADA CORPORA

TIONTION

TION

P.O. Box 526, Depot 1

Hamilton, Ontario L8L 7X6

905-662-6600

Fax 905-263-9308

1-800-263-9308

Toll Free Fax 1-866-835-9624

www.selkirkcanada.com

19/03/04

SELKIRK LLCSELKIRK LLC

SELKIRK LLC

14801 Quorum Drive

Dallas, Texas, USA 75240

972-560-2000

Fax 972-560-2428

1-800-992-VENT (8368)

Toll Free Fax 1-877-393-4145

www.selkirkinc.com

US C

PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING YOUR

INSTALLATION. FAILURE TO INSTALL THIS SYSTEM IN ACCORDANCE WITH

THESE INSTRUCTIONS WILL VOID THE CONDITIONS OF CERTIFICATION AND

THE MANUFACTURERS WARRANTY . KEEP THESE INSTRUCTIONS IN A SAFE

PLACE FOR FUTURE USE.

Tested to

*UL103HT & ULC-S641

A MAJOR CAUSE OF CHIMNEY CONNECTOR RELATED FIRES

IS FAILURE TO MAINTAIN REQUIRED CLEARANCES

(AIR SPACES) TO COMBUSTIBLE MATERIALS.

IT IS OF THE UTMOST IMPORTANCE THAT THIS

DOUBLE WALL CHIMNEY CONNECTOR BE INSTALLED

ONLY IN ACCORDANCE WITH THESE INSTRUCTIONS

FACTORY BUILT CHIMNEY CONNECTOR

LISTED

INSTALLATION

INSTRUCTIONS

Summary of content (7 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FACTORY BUILT CHIMNEY CONNECTOR A MAJOR CAUSE OF CHIMNEY CONNECTOR RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS. IT IS OF THE UTMOST IMPORTANCE THAT THIS DOUBLE WALL CHIMNEY CONNECTOR BE INSTALLED ONLY IN ACCORDANCE WITH THESE INSTRUCTIONS C ® US LISTED Tested to *UL103HT & ULC-S641 PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING YOUR INSTALLATION.
PAGE 2
TYPES OF APPLIANCES ATTENTION! The orientation of all chimney connector components must be with the crimped end (outer black pipe) pointing up, towards the chimney (see diagram below). Your Chimney Connector is intended to connect a gas, liquid, or solid fuel appliance normally producing flue gases of 650°C/ 1200°F (Canada), 540°C/1000°F (US - to the Temperature requirements of UL103HT) or less to a factory built or masonry chimney.
PAGE 3
INSTALLATION OF THE UNIVERSAL CHIMNEY ADAPTER STEP 1 : Slide the Universal Chimney Adapter (CA) over the male end of either the Stove Pipe Adapter (ASE) or the Smoke Pipe Adaptor all the way until snug to bead and beveled edge. See Figure 1. Step 2. Pre-drill 3 evenly spaced holes into the crimped end of the DSP through the Chimney Pipe Adaptor with a 3/32 metal drill bit. Secure in place with 3 #8 X 1/2” stainless steel sheet metal screws (not supplied).
PAGE 4
INSTALLATION TYPE #1 (See Figure A) This installation is used when the chimney system is located immediately above the appliance. 1. Place the Telescopic Length on top of the appliance with the male (crimped) end up, and the female end over the appliance outlet collar. Attach it with the 3 metal screws supplied. If the collar of your appliance is too large for the Telescopic Length to fit over you will have to use a stove adapter on top of the stove before installing the Telescopic Length. 2.
PAGE 5
3. Extend the Telescopic Length until it connects with the 90o Elbow and secure the upper and lower sections of the Telescopic Length in place with the 3 metal screws supplied. Fasten the Telescopic Length and the 90o Elbow together with the 3 metal screws provided. If the installation requires more length than provided by the telescopic length then install the fixed length(s) on the appliance and the telescopic length next to the 90o Elbow.
PAGE 6
LIMITED LIFETIME WARRANTY LIMITED LIFETIME WARRANTY: Selkirk Canada Corporation, ( “we”, “us”, “our”) warrants Chimney & Venting products * to be free from defects in material and workmanship for as long as the original consumer owns the system. For products installed after January 1, 2000, for a period of Ten (10) years from original installation, we will provide replacement product with a similar or like quality of available product, free of charge excluding any installation costs.
PAGE 7
INSTALLATION INFORMATION keep in safe place for future reference MODEL OF CHIMNEY: _______________________________ TYPE OF APPLIANCE: ______________________________ INSTALLATION DATE: ____________________________ DESCRIPTION OF INSTALLATION (Chimney and Chimney Connector configuration) ______________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________