User's Manual

ManualsBrandsMetalligence Technology ManualsElectronicsZigbee RF Module

HWM6505-DW

ZigBee Door Window Module User Guide

HWM6505-DW is a door window sensor with ZigBee RF communication. The home

security system is built by a Zigbee networks to combine components as controller panel,

sensors, sirens, keyfob, and keypad. It detects open or close status of door or window,

and informs system controller by ZigBee. HWM6505-DW ascertains open/close status by

a magnet part, when the magnet is close to sensor, it means close; it shows open when

the magnet moves away.

Features

 Small size for easy furnishing

 Long-life 3V lithium battery operated

 Outstanding communication range

 Tamper switch avoids physical attack

Specification

ZigBee RF Characteristic

 RF Protocol: IEEE 802.15.4

 RF frequency: 2405MHz~2480MHz

 Channel Bandwidth: 5MHz

 ZigBee Encryption: AES 128bits

Dimension

 L41.5 x W11 mm

Temperature

 Operating: -10ºC ~ 50ºC (32ºF ~ 132ºF)

 Storage: -10ºC ~ 60ºC (-4ºF ~ 158ºF)

Operating Humidity

 10% ~ 85% Non-Condensing

Compliance

 FCC subpart 15B and subpart 15C

 UL/cUL

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

This device and its antenna(s) must not be co-located or operation in conjunction with any

other antenna or transmitter.

IMPORTANT NOTE

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance

20cm between the radiator & your body.

IMPORTANT NOTE

This module is intended for OEM integrator only and limited to inserted to similar host

device (Brand: Metalligence and Model: HWS6505-DW) which is battery powered host

devices and has a plastic housing without any metal shielding. The OEM integrator is still

responsible for the FCC compliance requirement of the end product, which integrates this

module.

20cm minimum distance has to be able to be maintained between the antenna and the

users for the host this module is integrated into. Under such configuration, the FCC

radiation exposure limits set forth for an population/uncontrolled environment can be

satisfied.

Any changes or modifications not expressly approved by the manufacturer could void the

user's authority to operate this equipment.

Summary of content (2 pages)

PAGE 1
HWM6505-DW ZigBee Door Window Module User Guide HWM6505-DW is a door window sensor with ZigBee RF communication. The home security system is built by a Zigbee networks to combine components as controller panel, sensors, sirens, keyfob, and keypad. It detects open or close status of door or window, and informs system controller by ZigBee. HWM6505-DW ascertains open/close status by a magnet part, when the magnet is close to sensor, it means close; it shows open when the magnet moves away.
PAGE 2
USERS MANUAL OF THE END PRODUCT In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment.