Instructions / Assembly
FAILURE TO UNDERSTAND AND FOLLOW ALL SAFETY RULES AND ASSEMBLY INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH.
DO NOT OVERLOAD:
This portable work platform is designed to support a maximum load of 250 lb (113 kg).
METAL CONDUCTS ELECTRICITY:
Do not use this equipment where contact may be made with power lines or other live electrical circuits.
OPERATIONAL SAFETY
PROPER SETUP
1. Before using the plank, check that all parts function properly and
there is no damage. Make sure rivets and joints are secure and
tight.
2. A damaged plank shall be removed immediately from service and
shall not be used until repairs have been completed and tested by
the manufacturer.
3. If the plank is exposed to excessive heat or re, it shall be removed
immediately from service and destroyed due to loss of structural
strength.
4. DO NOT apply impact loads to the plank. NEVER attempt to
straighten a deformed plank section or part.
5. Oil, grease or any other slippery material shall not be permitted on
the surface of the plank.
6. Users shall never use the planks when it is covered with ice or snow,
unless all ice and snow is removed and the plank is spread with
sand to prevent slipping.
7. Users shall never use the plank during storms or high winds.
8. Keep your footwear dry and clean. Footwear with leather soles shall
NOT be worn whilst using the plank. Wear slip-resistant shoes.
9. Do NOT use the plank for cantilever applications. NEVER stand on
the part of the plank that extends beyond the supporting point of
the ladder.
10. Ropes and other binding materials shall NEVER be used to sus-
pend the plank.
11. Free-standing plank supports with a height to base ratio of more
than 4:1 must be prevented from tipping by securing with ropes or
other steadying means.
12. The total combined weight of each user and materials shall NOT
exceed the rated working load. DO NOT overload.
13. The ends of the plank must be properly supported and exceed the
supports no less than 12 in. (30 cm) and no more than 18 in. (45
cm).
14. The plank shall only be used when the work surface is level.
15. The support footing for the plank trestles shall be rigid, secure and
capable of carrying the maximum intended load without displace-
ment or settling.
16. Unstable objects, such as barrels, boxes, loose bricks or concrete
blocks shall not be used to support this plank.
17. Only extend the plank sections when on the ground, NEVER by
bouncing while on the supports.
18. DO NOT extend/retract the plank while standing on it.
19. Tag lines shall be attached to materials hoisted onto the plank.
20. Unstable objects, such as barrels, boxes, loose bricks, tools and
debris shall not be allowed to accumulate on the plank.
21. Safety harnesses and fall prevention lifelines shall be used by each
user if the plank is used more than 10 ft (3 m) above the ground or
oor. The lifelines must be secured to a suitable structural member
other than the one of the plank.
22. Setup and keep the plank close to the work. Avoid pushing or pull-
ing while on the plank. DO NOT overreach.
23. Overhead protection shall be provided to users on the plank when
in the vicinity of overhead hazards.
24. DO NOT use ladders or other items to attain greater heights when
on the plank.
25. Do not use planks if you tire easily or are subject to fainting spells,
or are using medication or alcohol, or are physically impaired.
26. Never climb onto the plank from another ladder unless both the
plank and the ladder are secured rmly from moving or shifting in
all directions.
27. When moving the plank, DO NOT use the plank to ride on or trans-
port tools and equipment.
28. DO NOT alter or remove any part or device that limits the minimum
or maximum length of the plank.
29. DO NOT setup and leave the plank unattended when children are
present.
30. DO NOT setup the plank where objects may strike the plank eg. in
front of doors and windows.
31. NEVER apply an impacting or prying force to the plank or drop
items onto the plank.
32. DO NOT use the plank near acids or corrosive substances or any
other material that could damage the plank.
PROPER CARE AND STORAGE
1. Store the plank in a safe and dry place.
2. The plank shall be secured when being transported.
3. NEVER store materials on the plank.
4. Keep the plank free and clean of any foreign materials.
5. Destroy plank if broken, worn or if exposed to re or chemical cor-
rosion.
ENGLISHENGLISH