Installation Guide

ManualsBrandsMetalux ManualsCommercial LightingFPanel 62.2-Watt 2 ft. x 4 ft. White Integrated LED Dimmable Flat Panel Troffer Cool White

IB519062EN Metalux

FP Panel Instructions

Instructions pour panneau FP

Instrucciones del panel FP

IMPORTANT: Read carefully before installing fixture.

Retain for future reference.

WARNING

Risk of fire, electrical shock, cuts and or other casualty

hazards. This product must be installed in accordance

with the applicable installation code by a qualified

electrician or a person familiar with the construction

and operation of the product and the hazards involved.

Eaton assumes no responsibility for claims brought

about by improper or careless installation or handling

of this product.

ATTENTION

Receiving Department: Note actual fixture description

of any shortage or noticeable damage on delivery

receipt. File claim for common carrier (LTL) directly

with carrier. Claims for concealed damage must be

filed within 15 days of delivery. All damaged material,

complete with original packing must be retained.

CAUTION

Edges May Cut. Handle with care.

CAUTION

Risk of burn. Disconnect power and allow fixture to

cool before maintenance.

WARNING

Risk of Fire and Electric Shock. If not qualified, consult

an electrician.

NOTICE

Ground screw provided in proper location. Do not

relocate.

CAUTION

Risk of Electric Shock. The light source contained

in this luminaire shall only be replaced by the

manufacturer or his service agent or a similar qualified

person.

NOTICE

Use 16-18 AWG solid or stranded wire for push-in

terminals.

CAUTION

• Connect fixture to a 120/277 volt, 60 Hz power source. Any other connection voids the warranty.

• This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

WARNING

FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly

approved by the manufacturer could void the user’s authorization to operate this equipment.

Summary of content (8 pages)

PAGE 1
Metalux IB519062EN FP Panel Instructions Instructions pour panneau FP Instrucciones del panel FP CAUTION IMPORTANT: Read carefully before installing fixture. Retain for future reference. Risk of burn. Disconnect power and allow fixture to cool before maintenance. WARNING Risk of fire, electrical shock, cuts and or other casualty hazards.
PAGE 2
FP Panel Instructions For T-Grid Mounting 6. 1. Turn off the power at the main fuse/breaker box. 2. Carefully open carton and remove panel from packaging. 3. Locate fixture junction box cover and slide to remove it (Fig. 1). 4. Remove appropriate knockout(s) for power supply wiring. Grid clips are provided for additional retention to ceiling system. Orient 4 tabs on back of fixture over T-GRID by bending tabs up 90 degrees perpendicular to back of fixture.
PAGE 3
FP Panel Instructions 8. Tuck all wires and wire nuts into the fixture junction box, replace electrical access plate, and snap securely into place (Fig. 6). push Figure 6. 9. To clean fixture use a small amount of water on a cloth and wipe the lens. Do not use chemicals on the lens as this could cause damage. 10. Turn breaker on. Use wall switch to verify light turns on. FP Panel Instructions IB519062EN www.eaton.
PAGE 4
Instructions pour panneau FP AVERTISSEMENT MISE EN GARDE Risques d'incendie, de décharge électrique, de coupures et autres dangers de blessure. Ce produit doit être installé selon le code d'installation applicable par un électricien qualifié ou une personne à l'aise avec la construction et le fonctionnement du produit ainsi qu'avec les dangers potentiels. Eaton n'assume aucune responsabilité pour les réclamations provenant de l'installation ou de la manipulation incorrecte ou négligente de ce produit.
PAGE 5
Instructions pour panneau FP 2x2 1x4 2x4 4,2 kg (9,4 lb) 4,4 kg (9,8 lb) 8,4 kg (18,5 lb) 7. Utilisez une entrée défonçable pour acheminer le câble d’alimentation. Utilisez les trois capuchons de connexion fournis pour raccorder le fil de mise à la terre au câble d’alimentation vert, le câble noir (Li11ne) au câble d’alimentation noir et le câble blanc (neutre) au câble d’alimentation blanc (Fig. 5).
PAGE 6
Instrucciones del panel FP ADVERTENCIA PRECAUCIÓN Riesgo de inflamabilidad, descarga eléctrica, cortes y otros riesgos de muerte. Un electricista cualificado o persona con conocimientos sobre la construcción y el funcionamiento del producto y los riesgos implicados debe instalarlo de conformidad con el código de instalación aplicable. Eaton no se responsabiliza por los reclamos presentados respecto de la instalación y la manipulación inapropiadas o negligentes de este producto.
PAGE 7
Instrucciones del panel FP 2x2 1x4 2x4 9,4 lb (4,2 kg) 9,8 lb (4,4 kg) 18,5 lb (8,4 kg) 7. Utilice el expulsor de apertura para ingresar la línea de alimentación. Utilice los tres empalmes plásticos provistos para conectar el cable de tierra con el cable de alimentación verde, el cable negro (li11ne) con el cable de alimentación negro y el cable blanco (neutro) con el cable de alimentación blanco (Imagen 5).
PAGE 8
Warranties and Limitation of Liability Please refer to www.eaton.com/LightingWarrantyTerms for our terms and conditions. Garanties et limitation de responsabilité Veuillez consulter le site www.eaton.com/LightingWarrantyTerms pour obtenir les conditions générales. Garantías y Limitación de Responsabilidad Visite www.eaton.com/LightingWarrantyTerms para conocer nuestros términos y condiciones. Eaton 1121 Highway 74 South Peachtree City, GA 30269 P: 770-486-4800 www.eaton.