Instructions / Assembly

1
PACKAGING CONTENTS /CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETE
Instruction Manual/Directives/Instrucciones
Questions?/Questions / ¿Preguntas?/ 1-800-334-6871 www.eaton.com/lighting
INSTALLATION INSTRUCTIONS
Note: This product is intended for either single
mount or continuous row applications.
1. Turn off the power at the main fuse/breaker box.
Carefully open carton and remove fixture from
carton.
2. To remove the channel cover with LED’s from main
channel body squeeze beneath the embossed
locking tabs and lift the channel cover. Do this for
all locking tab locations (Fig. 1). Avoid pulling on the
ends of channel cover to prevent bending. Place
channel cover in a safe location.
3. Remove appropriate knockout(s) for power
supply wiring. (Fig. 2)
4. Disconnect ground (green) and LED wires (red and
black) and set channel cover aside.
5. Wiring must comply with all applicable electrical
codes. (Figure 3)
6. Install luminaire using keyholes (surface mount) or
via chain, s-hooks or v-brackets (suspension.)
Hardware not included.
Note: See row mounting section if row mounting
before continuing to step 7.
7. Reconnect ground (green) and LED wires (red
and black), and reinstall channel cover onto
channel by hooking one side of it around channel
and then pushing the other side up and over the
channel embosses. To prevent bending of the
channel cover, start in the middle of the fixture and
work your way toward the ends. (Figure 4)
8. Remove protective film from lens before energizing
fixture.
9. Turn breaker back on to verify light fixture turns
on. If circuit is attached to a switch, be sure to turn
switch on.
ITEMS REQUIRED
Purchase separately
• Stud mount (2) 1 1/2 in. long #8 or larger wood screws and a #10 flat washer
• Drywall mount (2) 3 in. long 3/16” or larger diameter toggle bolt and #10 flat washer
(if joist cannot be located)
• Phillips screwdriver
• Flat head screwdriver
• Pliers
• Hammer
• Safety glasses & Safety gloves
• Ladder
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Read and follow these instructions.
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• Risk of fire/electric shock.
• Ground fixture to avoid potential electric shock.
• Turn off the power at fuse or circuit breaker box before installation and maintenance.
• Edges may cut. Handle with care.
CAUTION
• Connect fixture to power source noted on product identification label. Any
other connection voids the warranty.
• Fixture should be installed by persons with experience wiring or by a qualified
electrician. The electrical system, and the method of electrically connecting the fixture
to it, must be in accordance with the National Electrical Code and local building codes.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
WARNING: FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by the manufacturer
could void the user’s authorization to operate this equipment.
ENGLISH
A. (1) Fixture channel
(1) Canal du luminaire
(1) Canal de la luminaria
WARNING
Strip Model ST
B. (1 or 2) Channel cover with LED’s and lens assembly
(1 or 2) Couvercle du canal avec DEL et ensemble da
la lentille
(1 or 2) Cubierta del canal con luces LED y Unidad de la
lente
C. (3) Push in connectors or wire nuts
(3) Conectores a presión o tuercas
para cables
(3) Emboîtez les connecteurs ou les
serre-fils
D. (1) Row D. Aligner
(1) Mécanisme d’alignement de rangée D
(1) Alineador de la Fila D.
Fig. 2
Fig. 1
Fi
g. 4
Fig. 3
Black - Line
DRIVER/BALLAST
Green/Yellow - Ground
White - Neutral