Installation Guide

Instruction Manaual/Instrucciones/Directives
Questions?/¿Preguntas/Questions ? 1-800-334-6871 [e-mail]
1
LED
PACKAGING CONTENTS/CONTENIDO DEL PAQUETE/CONTENU DU PAQUET
ITEMS REQUIRED
(Purchase separately)
• Phillips Head Screwdriver
WARNINGS AND CAUTIONS
Safety Information • Read carefully for your protection
• Turn off the power at fuse or circuit breaker box before installation and maintenance.
• Wear rubber-soled shoes and work on a sturdy ladder.
• NOTE: This fixture should be used on a 120-Volt fused circuit. (Check fixture labeling)
• Fixture must be installed according to National Electric Code and local building codes.
• Ground fixture to avoid potential electric shock.
• Handle metal parts carefully to prevent cuts.
• To avoid a hazard to children, account for all parts and destroy all packing materials.
• If you are unsure about wiring, consult a qualified electrician.
• If any part is missing or damaged, do not attempt to assemble, install or
operate the product.
• DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT.
• This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
A. Round diffuser
Difusor acrílico
Diffuseur acrylique
B. Fixture housing (Housing shown - 12”, 16”, 20”)
Alojamiento del accesorio (Se muestran los alojamientos de 12”, 16” y 20 “)
Boîtier du luminaire (Boîtier illustré - 30,5 cm [12 po], 40,6 cm [16 po], 50,8 cm [20 po])
ENGLISH
WARNING: FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by the manufacturer
could void the user’s authorization to operate this equipment.
SAVE THESE INSTRUCTIONS.
WIRING AND FIXTURE INSTALLATION
1. TURN POWER OFF AT MAIN FUSE/ BREAKER BOX. Carefully open carton, remove fixture
from carton.
2. Carefully open carton, remove fixture from carton
and remove the diffuser. For safe operation, use only
the machine screws (C) included in the hardware kit.
Screw both 25 mm #8-32 machine screws (C) in the
electrical box until there is approximately 3/8” inch
between the ceiling and the underside of the screw
head (fig. 1).
3. On 12”, 16” and 20” models, open the 3 diffuser
latches and remove diffuser from fixture housing (fig. 2).
NOTE: 8” model does not include diffuser latches but
is twist lock diffuser (see fig. 6 to remove).
4. Locate wires in outlet box. Connect all fixture wires
to power supply wires. White to white, black to
black, and green to green with wire nuts (D).
Caution: If supply wires (or power supply cord) are
located within 3” of the ballast, use wires (cord)
suitable for at least 90ºC (194ºF). Do not use fixture
on dimming circuits.
5. Align the fixture plate with the machine screws
installed in the junction box in step 2, then rotate
fixture plate to lock in place (fig. 3). Use screw driver to
tighten screws firmly against fixture housing (B).
6. For 12”, 16” and 20” models, securely mount the round
diffuser (A) to the fixture housing (fig. 4) by turning the 3
diffuser latches to the right until they are closed (fig. 5).
For 8” model, place diffuser on fixture housing and twist
clockwise to lock into place (fig. 6).
7. To clean diffuser, use a mild detergent and water.
Wipe and allow to air dry.
8. Restore power to the electrical box. Turn the light
switch on to activate the fixture.
C. (2) 8-32 x 25 mm #8-32 machine screws
(2) tornillos para máquinas n.º 8-32 de 8-32 x 25 mm
(2) vis de mécanique no 8-32 x 25 mm (1 1/2 po)
1 2
D. (3) Wire connectors
(3) Conectores de cable
(3) Serre-fils
White Round
LED Flushmount
Luminaria LED blanca, redonda
para montaje rasante
Luminaire fluorescent DEL
rond encastré
FMLED8WH840PR
(8 inch/20 cm)
FMLED12WH840PR
(12 inch/30 cm)
FMLED16WH840PR
(16 inch/41 cm)
FMLED20WH840PR
(20 inch/50 cm)
3
4
5
6