INSTALLATION INSTRUCTIONS FOR PART 95-2009 APPLICATIONS GM/SUZUKI MULTI KIT 95-2009 KIT FEATURES • Double DIN Radio Provision • Stacked ISO Mount Units Provision KIT COMPONENTS • A) Double DIN Brackets • B) Double DIN Trim Plate • C) Spacers • D) (4) Carriage Bolts • E) (4) Kep Nuts • F) (3) Screws-(3) Speed Clips B A C D E WIRING AND ANTENNA CONNECTIONS (Sold Separately) • Wiring Harness - Please see www.metraonline.
95-2009 VEHICLE APPLICATION CONTENTS *Note: Refer also to the instructions included with the aftermarket radio.
95-2009 DASH DISASSEMBLY BUICK • CENTURY 1997-2005 / REGAL 1995-2004 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove the plastic trim piece to the left of the glove box and (1) Phillips screw exposed. 3 Unsnap the top edge of the knee bolster panel. 4 Remove (1) Phillips screw from the panel. 5 Remove the ashtray cluster and (2) Phillips screws from each side. 6 Unclip the entire dash trim bezel and remove. 7 Open doors and unsnap end caps from each side of dash.
95-2009 DASH DISASSEMBLY BUICK • LESABRE / PARK AVENUE 1995-1999 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unsnap the climate control trim panel (from door to door) and remove (4) Phillips screws exposed. 3 Pop out the a/c vents and remove (1) Phillips screw exposed in each vent cavity. 4 Unclip the radio trim bezel and remove. 5 Remove the screws securing the factory head unit and disconnect the wiring. Continue to kit assembly.
95-2009 DASH DISASSEMBLY BUICK • LESABRE / PARK AVENUE 2000-2005 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Open drivers door and unsnap and remove dash end cap. 3 Unsnap and remove trim along center of dash. (One piece on right and one on left of wheel) 4 Unsnap and remove radio/instrument bezel. 5 Remove (2) screws in order to remove radio. Continue to kit assembly.
95-2009 DASH DISASSEMBLY BUICK • RENDEZVOUS 2002-2007 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Open center console and remove 2 screws at front of console opening. 3 Remove liners from cup holders and storage pocket next to cup holders, then remove screws. Unsnap and remove panel. 4 Remove (2) screws from bottom of radio/climate control bezel, unclip and remove. 5 Remove (3) 9/32" hex head screws to remove radio. Continue to kit assembly.
95-2009 DASH DISASSEMBLY BUICK • RIVIERA 19961 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unsnap left side panel exposing (1) Phillips screw to remove. 3 Remove (1) Phillips screw and unsnap right side panel to expose (1) Phillips screw beneath panel and remove. 4 Unsnap underside of overhanging dash to unsnap (6) plastic rivets and remove panel. 5 Remove (5) hex head screws now exposed under overhang.
95-2009 DASH DISASSEMBLY BUICK • ROADMASTER 1995-1996 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip dash panel sides and remove. 3 Unclip panel below steering column and remove. 4 Remove (2) 7mm screws above instrument cluster. 5 Set parking brake, turn car on, and move shifter to the lowest gear. Tilt steering wheel down then unsnap entire instrument cluster/radio panel and remove. 6 Remove (3) 7mm screws to remove radio. Continue to kit assembly.
5-2009 DASH DISASSEMBLY BUICK • SKYLARK 1996-1998 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove (6) 9/32" screws inside glove box. 3 Under glove box and drivers knee bolster, remove (2) plastic panels by turning (2) 1/4 turn fasteners per side. 4 Remove (4) 9/32" screws revealed. (2 per side). 5 Unsnap panel from driver's side to passenger's side. 6 Remove (3) 9/32" screws to remove radio. Continue to kit assembly.
95-2009 DASH DISASSEMBLY CADILLAC • ESCALADE 2003-2006 CHEVROLET • AVALANCHE 2003-2006 SILVERADO 2003-2007 / SUBURBAN 2003-2006 TAHOE 2003-2006 GMC • SIERRA 2003-2007 YUKON / DENALI / XL 2003-2006 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unsnap and remove dash bezel. 3 Remove (3) 9/32" screws and remove radio. Continue to kit assembly.
95-2009 DASH DISASSEMBLY CADILLAC • FLEETWOOD FLEETWOOD BROUGHAM 1990-1996 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Carefully unsnap trim panel above a/c controls. 3 Remove (2) 7mm screws at the top of the radio/air conditioning bezel, then unclip panel and remove. 4 Remove (4) 7mm screws that hold the radio in, slide radio out, unplug the radio harnesses and remove radio. Continue to kit assembly.
95-2009 DASH DISASSEMBLY CADILLAC • FLEETWOOD FLEETWOOD BROUGHAM 1990-1996 RADIO BRACKET DISASSEMBLY 1 Remove (4) 10mm nuts, (2) on top of the radio and (2) on the bottom of the radio, that hold the factory mounting brackets on. save brackets and nuts for kit assembly.
95-2009 DASH DISASSEMBLY CADILLAC • ELDORADO 1992-1995 SEVILLE 1992-1995 1 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Using a panel removal tool, pry out on the radio trim ring and remove. Use extreme care when removing). 3 Gently pry up on the ashtray/gear shifter trim bezel and remove. (CAUTION: Some models are equipped with bezels made of real wood. 4 Remove (2) nuts securing the bottom of the factory head unit and disconnect the wiring.
95-2009 DASH DISASSEMBLY CHEVROLET • BLAZER 2002-2005 S-10 2002-2004 (WITH DOUBLE DIN RADIO) GMC • SONOMA 2002-2004 OLDSMOBILE • BRAVADA 1998-2001 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove (2) 9/32" hex-head screws from the knee bolster panel. 3 Pull down on the panel and remove the 9/32" hex-head screws exposed on the bottom of the dash trim bezel. 4 Remove (1) Phillips screw above the instrument cluster. 5 Unclip the dash trim bezel and remove.
95-2009 DASH DISASSEMBLY CHEVROLET • CAVALIER 2000-2005 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Open drivers door and remove fuse panel on end of dash. 3 Open passenger door and remove panel on end of dash. 4 Remove (1) Phillips screw from each side exposed. 5 Remove (3) screws from top of glove box liner. 6 Remove (2) screws from the top-left corner of the glove box cavity. 7 Remove (1) Phillips screw from the defroster duct.
95-2009 DASH DISASSEMBLY CHEVROLET • COLORADO 2004-2010 GMC • CANYON 2004-2010 ISUZU • I-290/I-370 2007-2008 I-280/I-350 2006 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unsnap and remove the entire panel surrounding the radio and A/C controls. (Figure A) 3 Remove (3) 9/32”screws securing the radio to remove. (Figure B) Continue to kit assembly.
95-2009 DASH DISASSEMBLY CHEVROLET • EXPRESS VAN 2001-2002 GMC • SAVANNA 2001-2002 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unsnap and remove small trim panel below steering column. 3 Unsnap radio/climate/instrument panel. 4 Move shift lever to first gear position. 5 Rotate panel counterclockwise to lift over steering column and remove. 6 Remove (3) 9/32" hex head screws to remove radio. Continue to kit assembly.
95-2009 DASH DISASSEMBLY CHEVROLET • EXPRESS VAN 2003-2007 GMC • SAVANNA 2003-2007 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove (2) 10mm bolts from below knee bolster under steering column and remove panel. 3 Remove (2) 10mm bolts from panel below passenger dash airbag and remove panel. 4 Remove (2) 10mm nuts from inside center pocket between power outlets. 5 Unsnap and remove radio and instrument cluster panel.
95-2009 DASH DISASSEMBLY CHEVROLET • IMPALA 2000-2005 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip each side of the dash trim bezel (fuse access) and remove (1) Phillips screw exposed on each side. 3 Remove (2) Phillips screws under the instrument cluster. 4 Unclip the trim panel above the pedals. (It is not necessary to remove the panel it can be left hanging). 5 Remove (2) Phillips screws from the knee panel.
95-2009 DASH DISASSEMBLY CHEVROLET • MALIBU 2001-2003 MALIBU CLASSIC 2004 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unsnap and remove radio bezel. 3 Remove (3) bolts and remove radio. Continue to kit assembly.
95-2009 DASH DISASSEMBLY CHEVROLET • METRO 1995-2001 SUZUKI • SWIFT 1995-2001 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove the ashtray and (2) Phillips screws exposed. 3 Remove (2) Phillips screws above the radio opening. 4 Unclip the radio trim bezel and disconnect the cigarette lighter wiring. 5 Remove (2) screws securing each side of the factory head unit and (1) screw from the rear support. 6 Slide the unit out and disconnect the wiring.
95-2009 DASH DISASSEMBLY CHEVROLET • MONTE CARLO 2000-2005 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip the trim panel above the pedals. (It is NOT necessary to remove the panel it may be left hanging). 3 Remove (2) 9/32" screws from the knee panel and unclip the panel. 4 Unsnap the driver's side fuse panel cover and remove (1) 9/32" screw. 5 Open the glove box and remove (1) 9/32" screw from the upper left corner.
95-2009 DASH DISASSEMBLY CHEVROLET • SSR 2003-2006 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the (3) climate control knobs. (Figure A) 1 23 3 Unclip and remove the long trim panel below the radio and passenger air bag. (Figure B) A 4 Unclip and remove the small trim panel to the left of the steering wheel. (Figure C) 5 Remove the (5) 9/32” screws securing the radio/instrument panel then unclip and remove the panel.
95-2009 DASH DISASSEMBLY CHEVROLET • TRACKER 1992-2004 SUZUKI • SIDEKICK 1992-1998 / VITARA 1999-2005 GRAND VITARA 1999-2002 XL-7 2001-2002 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove the cigarette lighter and climate control knobs. 3 Remove the ashtray and (1) screw exposed. 4 Pull out on the climate control cluster and remove (2) screws exposed. 5 Unclip the radio trim bezel.
95-2009 DASH DISASSEMBLY CHEVROLET • TRAILBLAZER 2002-2009 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove (2) Phillips screws inside instrument cluster. 3 Remove (1) Phillips screw under climate controls to the left of the power outlet. 4 Remove (2) 7mm hex heads from under steering column and lower the panel. Remove (3) Phillips screws around steering wheel. 5 Unsnap and remove bezel. (Use caution pulling over hazard switch.
95-2009 DASH DISASSEMBLY CHEVROLET • VENTURE 2000 OLDSMOBILE • SILHOUETTE 2000 PONTIAC • MONTANA (EXCEPT SV6) 2000 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove the ashtray and (1) phillips screw exposed in the ashtray cavity. 3 Remove (1) Phillips screw from the cigarette lighter compartment. 4 Remove (2) Phillips screws securing the factory head unit and disconnect the wiring. Continue to kit assembly.
95-2009 DASH DISASSEMBLY CHEVROLET • VENTURE 2001-2005 OLDSMOBILE • SILHOUETTE 2001-2004 PONTIAC • MONTANA (EXCEPT SV6) 2001-2005 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove the ashtray and (1) phillips screw exposed in the ashtray cavity. 3 Remove (1) Phillips screw from the cigarette lighter compartment. 4 Remove (2) Phillips screws securing the factory head unit and disconnect the wiring. Continue to kit assembly.
95-2009 DASH DISASSEMBLY GMC • ENVOY 2002-2009 / ISUZU ASCENDER 2003-2009 OLDSMOBILE • BRAVADA 1998-2004 BUICK • RAINIER 2004-2007 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2. Remove (4) Phillips screws, (2) from left and (2) from right of carpeted panel. 3. Slide carpeted panel down and backwards to reveal (2) Phillips screws and remove. 4. Unsnap radio bezel and unplug cigarette lighter and accessories. 5. Remove (3) screws and remove radio.
95-2009 DASH DISASSEMBLY HONDA • PASSPORT 1998-2002 ISUZU • AMIGO 1998-2000 / RODEO 1998-2004 RODEO SPORT 2001-2003 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove the ashtray and (1) Phillips screw exposed in the ashtray cavity. Unclip and remove the trim panel surrounding the factory radio. Remove (4) Phillips screws securing the factory radio and disconnect the wiring. Continue to kit assembly.
95-2009 DASH DISASSEMBLY HUMMER • H2 2003-2007 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Open center console and remove (4) 9/32” screws from console box and remove box. 3 Remove (4) phillips screws from hinge on console door inside console and remove door. 4 Loosen (1) T-15 torx on forward facing side of shift lever and pull up to remove. 5 Unclip cup holder/shifter trim assembly and remove. 6 Remove (6) Phillips screws from top of center console.
95-2009 DASH DISASSEMBLY HUMMER • H2 2003-2007 Continued from page 30. 8 Remove (1) 10mm bolt to right of shift lever. 9 Remove (2) Phillips screws from under console box on drivers side and (2) Phillips screws from under console trimtop on passenger side. 10- Slide control assembly rearwards. 11 Remove (2) T-30 torx bolts from top of rado/climate control trim and unclip and remove. 12 Remove (3) 9/32” screws that hold the radio in. Continue to kit assembly.
95-2009 DASH DISASSEMBLY OLDSMOBILE • ACHIEVA 19961 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Open the glove box, press inward on the walls of the glove box liner and remove the liner. 3 Remove (10) torx-head screws from the glove box location. 4 Remove (2) 9/32" hex-head screws under the steering column. 5 Unclip the dash trim bezel. 6 Remove the screws securing the factory head unit and disconnect the wiring. Continue to kit assembly.
95-2009 DASH DISASSEMBLY OLDSMOBILE • ALERO 1999-2004 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove shift knob by using a small screwdriver to remove U-clip from front of shifter and pull upward. 3 Unclip and remove shifter trim panel. 4 Unclip and remove radio and climate control panel by pulling from bottom. 5 Remove (3) 9/32" screws from radio and remove. Continue to kit assembly.
95-2009 DASH DISASSEMBLY OLDSMOBILE • AURORA 1995-2003 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip the radio trim bezel and remove the bezel. 3 Remove (2) 7mm screws securing the factory head unit and disconnect the wiring. Continue to kit assembly.
95-2009 DASH DISASSEMBLY OLDSMOBILE • CUTLASS 1997-1999 CUTLASS SUPREME 1995-1997 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip the radio trim bezel and remove. 3 Remove (2) ) 9/32" hex-head screws securing the factory head unit and disconnect the wiring. Continue to kit assembly.
95-2009 DASH DISASSEMBLY OLDSMOBILE • EIGHTY EIGHT 1994-1999 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip the radio trim bezel and remove. 3 Remove (2) ) 9/32" hex-head screws securing the factory head unit and disconnect the wiring. Continue to kit assembly. OLDSMOBILE • NINETY EIGHT 1994-1996 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Open the glove box and remove (2) hex-head screws securing the wood trim.
95-2009 DASH DISASSEMBLY OLDSMOBILE • INTRIGUE 1998-2003 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Open the center console storage compartment and remove (2) 9/32" hex-head screws exposed. 3 Remove the center console. 4 Unclip the radio trim bezel and remove. 5 Remove (2) 9/32" hex-head screws securing the factory head unit and disconnect the wiring. Continue to kit assembly.
95-2009 DASH DISASSEMBLY OLDSMOBILE • LSS 1996-1999 / REGENCY 1997-1998 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Open glove box and remove two-center trim bezels attached by screws. 3 Unsnap and remove radio trim bezel. 4 Remove (3) 9/32" hex-head screws and remove radio. Continue to kit assembly.
95-2009 DASH DISASSEMBLY PONTIAC • AZTEC 2001-2005 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Pull out cup holder inserts. 3 Remove (1) Phillips screw exposed inside bottom cup holder. 4 Unsnap and remove shifter trim with cup holders. 5 Remove (2) #15 torx at bottom of radio/climate bezel. Continue to kit assembly.
95-2009 DASH DISASSEMBLY PONTIAC • BONNEVILLE 2000-2005 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove (2) Phillips screws from the instrument cluster. 3 Unclip the ignition trim and remove. 4 Unclip the climate control/radio trim bezel and remove. 5 Depress the spring clips on each side of the factory head unit and remove. Continue to kit assembly.
95-2009 DASH DISASSEMBLY PONTIAC • GRAND AM 2001-2005 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unsnap and remove radio trim bezel. 3 Remove (3) 9/32” screws from radio brackets and remove radio. Continue to kit assembly.
95-2009 DASH DISASSEMBLY PONTIAC • SUNFIRE 2000-2005 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Open the glove box and remove (2) Phillips screws exposed on the right edge of the radio trim bezel. 3 Unclip the bezel and remove. 4 Remove (2) 7mm hex-head screws securing the factory head unit and disconnect the wiring. Continue to kit assembly.
95-2009 DASH DISASSEMBLY TOYOTA • MATRIX 2003-2004 PONTIAC • VIBE 2003-2008 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip the bottom edge of the radio trim panel then lift up and out to remove. (Figure A) 3 Remove (4) 10MM bolts securing the factory radio. (Figure B) Continue to kit assembly.
95-2009 DASH DISASSEMBLY SUZUKI • AERIO 2002 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip the dash trim bezel and remove. 3 Remove (4) Phillips screws securing the factory head unit and disconnect the wiring. Continue to kit assembly.
95-2009 DASH DISASSEMBLY SUZUKI • ESTEEM 19951 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove the climate control knobs. 3 Remove (1) Phillips screw located above the radio opening. 4 Unclip the radio trim bezel. 5 Remove (4) screws from the factory head unit, slide the unit out and disconnect the wiring. Continue to kit assembly.
95-2009 TAB INSTRUCTIONS CHEVY/GM/METRO/SUZUKI CADILLAC-FLEETWOOD/BROUGHAM *Note: Refer also to the instructions included with the aftermarket radio. A 1 GM vehicles. Cut tabs highlighted on both sides of both brackets. (Figure A) 2 CHEVY Tracker/METRO/SUZUKI. Cut tabs highlighted on both sides of both brackets. (Figure B) 3 CADILLAC Fleetwood/Broughham. Cut all tabs highlighted on both sides of both brackets. (Figure C) Continued on page 46.
95-2009 TAB INSTRUCTIONS ISUZU-PONTIAC/TOYOTA/ CADILLAC-ELDORADO/SEVILLE *Note: Refer also to the instructions included with the aftermarket radio. D Continued from page 46. 4 ISUZU Amigo/Rodeo/Rodeo Sport. Cut tabs highlighted. (Figure D) 5 TOYOTA Matrix/PONTIAC Vibe. Cut tabs highlighted. (Figure E) Cut (4) tabs highlighted on double DIN trim plate. (Figure H) 6 CADILLAC Eldorado/Seville. Cut tabs highlighted on double DIN brackets.
95-2009 KIT ASSEMBLY CADILLAC • FLEETWOOD FLEETWOOD BROUGHAM 1990-1996 KIT ASSEMBLY WITH FACTORY BRACKETS 1 Using carriage bolts and Keps nuts supplied, mount the factory brackets to the double DIN trim plate/double DIN bracket assembly, keeping in mind which bracket is top and which one is bottom.
95-2009 KIT ASSEMBLY CADILLAC • ELDORADO 1992-1995 SEVILLE 1992-1995 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Align the tabs on the bottom of the double DIN trim plate with notches in sub dash. 3 Secure with the (2) Carriage bolts and (2) Kep nuts provided. Continue to kit assembly.
95-2009 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION STACKED ISO MOUNT UNIT(S) PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the Double DIN brackets to the edge of the Double DIN trim plate. (Figure A) 2 Slide the Double DIN head unit or stacked ISO head units into the bracket/radio housing assembly and secure the Double DIN head unit or stacked ISO head units to the assembly using the screws supplied with the radio.
95-2009 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation.
95-2009 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV.
