Car Stereo System User Manual

ManualsBrandsMetra Electronics ManualsCar Stereo System95-7331

INSTALLATION INSTRUCTIONS FOR PART 95-7331

95-7331

KIT FEATURES

• Double DIN Radio Provision

• Stacked ISO Mount Units Provision

A) Radio Housing B) Double DIN Brackets

KIT COMPONENTS

Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver • Socket set

1-800-221-0932

TION

www.metr

aonline.com

TOOLS REQUIRED:

APPLICATIONS

KIA Amanti

2007-2009

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 95-7331 APPLICATIONS KIA Amanti 2007-2009 95-7331 KIT FEATURES • Double DIN Radio Provision • Stacked ISO Mount Units Provision KIT COMPONENTS A) Radio Housing B) Double DIN Brackets A B TOOLS REQUIRED: Small Flat Blade Screwdriver/ Panel Removal Tool • Phillips Screwdriver • Socket set 1-800-221-0932 © COPYRIGHT 2007-2008 www.metraonline.
PAGE 2
95-7331 TABLE OF CONTENTS Dash Disassembly - KIA Amanti 2007-2009. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2 Kit Assembly - Double DIN Radio Provision /Stacked ISO Mount Units Provision . . . . . . . . .3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 *Note: Refer also to the instructions included with the aftermarket radio.
PAGE 3
95-7331 DASH DISASSEMBLY KIA AMANTI 2007-2009 1 Disconnect the negative battery terminal to prevent an accidental short circuit. A 2 Unclip the top half of the shift knob and remove the “C” clip securing the shifter. Pull up on shifter to remove. (Figure A) 1 3 Unclip and remove the panel surrounding the shifter. (Figure B) 4 Unclip and remove top half of center console including the cup holders. (Figure C) B 5 Open center console and remove screw cover in bottom.
PAGE 4
95-7331 DASH DISASSEMBLY KIA AMANTI 2007-2009 7 Unclip the rear trim panel from the center console including a/c vents. Unplug and remove the rear trim panel. (Figure E) E 8 Remove (1) Phillips screw from each side at the rear of the center console. (Figure E) 9 Unclip the side panels from the front of the center console. It is not necessary to remove these panels. (Figure F) 10 Remove (4) Phillips screws securing center console then lift and slide the center console back out of the way.
PAGE 5
95-7331 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. 1 Snap the switches into the radio housing in the same location as removed from the factory radio. (Figure A) A 2 Snap the Double DIN brackets to the inside edge of the Radio Housing.
PAGE 6
95-7331 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.
PAGE 7
95-7331 NOTES 5
PAGE 8
95-7331 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV.