INSTALLATION INSTRUCTIONS FOR PART 95-7417 APPLICATIONS INFINITI 1996-1999 I-30 MERCURY 1993-2002 Villager NISSAN 1995-1998 200SX/240SX 1998-2001 Altima / 1998-2004 Frontier 1995-2003 Maxima / 1996-2004 Pathfinder/QX4 1997-2000 1993-2003 Quest / 1995-1999 Sentra 2000-2004 Xterra 95-7417 KIT FEATURES • DDIN Head Unit Provision • Stacked ISO DIN Head Unit Provision KIT COMPONENTS A) DDIN Trim plate B) DDIN Brackets A B TOOLS REQUIRED: Cutting Tool • Phillips Screwdriver • Socket Wrench 1-800-221-0932 w
95-7417 TABLE OF CONTENTS Dash Disassembly 1996-1999 Infiniti I-30 ................................................................. 1 1993-1995 Mercury Villager /1993-1995 Nissan Quest ............... 2 1996-1998 Mercury Villager/ 1996-1998 Nissan Quest ............... 3 1999-2002 Mercury Villager /1999-2003 Nissan Quest................ 4 1995-1999 Nissan Sentra /1995-1998 200 SX............................. 5 1995-1998 Nissan 240 SX............................................................
95-7417 DASH DISASSEMBLY 1996-1999 INFINITI I-30 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the shift lever trim panel and remove the (2) screws exposed. 3 Remove (1) screw to the left of the ashtray then unclip and remove the ashtray assembly. 4 Unclip and remove the clock/vent assembly. 5 Remove (4) screws securing the radio.
95-7417 DASH DISASSEMBLY 1993-1995 MERCURY VILLAGER 1993-1995 NISSAN QUEST 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove (1) screw above the climate controls. 3 Unclip and remove the radio trim panel. 4 Remove (4) screws securing the radio.
95-7417 DASH DISASSEMBLY 1996-1998 MERCURY VILLAGER 1996-1998 NISSAN QUEST 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove (4) plastic screws and screw anchors from the base of the storage compartment then remove the compartment. 3 Remove (2) Phillips screws from the base of the radio trim panel. 4 Remove (2) Phillips screws from above the radio opening. 5 Remove the ashtray. 6 Remove (4) screws securing the radio.
95-7417 DASH DISASSEMBLY 1999-2002 MERCURY VILLAGER 1999-2003 NISSAN QUEST 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Open the ashtray/cupholder assembly and depress the retaining clips on each side to remove. 3 Remove (2) Phillips screws from each side of the ashtray/cupholder. 4 Remove (4) plastic rivets from the lower pocket and slide the pocket back. Note: It is not necessary to fully remove the pocket. 5 Unclip the dash trim panel and remove.
95-7417 DASH DISASSEMBLY 1995-1999 NISSAN SENTRA 1995-1998 200 SX 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the dummy plate above the climate controls. 3 Remove (1) Phillips screw from behind dummy plate. 4 Unclip and remove radio trim panel. 5 Remove (4) Phillips screws securing radio.
95-7417 DASH DISASSEMBLY 1995-1998 NISSAN 240 SX 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the climate control trim panel and remove the (2) exposed behind. 3 Unclip and remove the shift lever trim panel and remove the (2) screws exposed behind. 4 Remove the ashtray and (1) Phillips screw exposed in the ashtray cavity. 5 Unclip and remove the radio trim panel, factory radio and pocket assembly.
5-7417 DASH DISASSEMBLY 1998-2001 NISSAN ALTIMA 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip the shift lever trim panel and remove (2) Phillips screws at the base of the radio trim panel. 3 Remove (2) Phillips screws above the radio opening. 4 Unclip and remove the radio trim panel. 5 Remove (4) Phillips screws securing the radio.
95-7417 DASH DISASSEMBLY 1998-2001 NISSAN FRONTIER 2000-2001 NISSAN XTERRA 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove the ashtray and the (2) Phillips screws exposed in the ashtray cavity. 3 Unclip and remove the radio trim panel. 4 Remove (4) Phillips screws securing the radio.
95-7417 DASH DISASSEMBLY 2002-2004 NISSAN FRONTIER 2002-2004 NISSAN XTERRA 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the shift lever trim panel. 3 Remove (2) Phillips screws exposed in the shift lever cavity. 4 Remove (2) Phillips screws under the climate control. 5 Unclip and remove the radio trim panel. 6 Remove (4) Phillips screws securing the radio.
95-7417 DASH DISASSEMBLY 1995-1999 NISSAN MAXIMA 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip the shift lever trim panel. 3 Remove the (2) Phillips screws at the base of the radio trim panel. 4 Remove (1) Phillips screw to the left of the ashtray and unclip the ashtray assembly. 5 Unclip and remove the clock/vent assembly. 6 Remove (4) Phillips screws securing the radio.
95-7417 DASH DISASSEMBLY 2000-2003 NISSAN MAXIMA 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the vent/radio trim panel. Note: For Bose systems the vent assembly will be removed without the trim panel. 3 Remove the ashtray insert and (1) Phillips screw exposed behind. 4 Unclip and remove the shift lever/ashtray trim panel.
95-7417 DASH DISASSEMBLY 1996-2000 NISSAN PATHFINDER/QX4 1997-2000 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove (2) Phillips screws from the base of the radio trim panel. 3 Unclip and remove the radio trim panel. 4 Remove (4) Phillips screws securing radio.
95-7417 DASH DISASSEMBLY 2001-2003 NISSAN PATHFINDER 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the vent/clock assembly. (Figure A) 3 Remove (2) Phillips screws from the top of the radio trim panel then remove the panel. (Figure B) 4 Remove (4) Phillips screws securing radio.
95-7417 KIT ASSEMBLY DOUBLE DIN HEAD UNIT PROVISION A 1 Slide the appropriate bracket into the trim plate aligning the holes in the trim plate to the clips on the bracket. (Figure A) 2 Attach the factory mounting brackets and the 95-7417 DDIN trim plate/bracket assembly to the DDIN head unit with the screws supplied with the unit.
95-7417 KIT ASSEMBLY STACKED ISO DIN HEAD UNIT PROVISION A 1 Slide the appropriate bracket into the trim plate aligning the holes in the trim plate to the clips on the bracket. (Figure A) 2 Attach the factory mounting brackets and the 95-7417 DDIN trim plate/bracket assembly to the stacked ISO DIN head units with the screws supplied with the units.
95-7417 FINAL ASSEMBLY FINAL ASSEMBLY 1 Locate the factory wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.
95-7417 NOTES 17
95-7417 INSTRUCTIONS 1-800-221-0932 REV. 07/28/09 www.metraonline.
