Car Stereo System User Manual

ManualsBrandsMetra Electronics ManualsAutomobile Accessories95-7504

INSTALLATION INSTRUCTIONS FOR PART 95-7504

95-7504

Mazda 3 2004-2009

KIT FEATURES

• Double DIN Radio Provision

• Stacked ISO Mount Units Provision

• Bonus Display Replacement Pocket

• A) Radio Housing • B) Double DIN Brackets • C) Double DIN Trim plate

•D) Display Replacement Pocket • E) Display Retention Brackets

• F) (2) 3/8” #10 Bolts and (2) #10 Nuts • G) (2) PC-7503 Panel Clips

KIT COMPONENTS

1-800-221-0932

www.metraonline.com

TOOLS REQUIRED:

APPLICATIONS

WIRING AND ANTENNA CONNECTIONS (Sold Separately)

Wiring Harness:

• 70-7903 - Mazda harness 2001-up

Antenna Adapter:

• Not required

Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 95-7504 APPLICATIONS Mazda 3 2004-2009 95-7504 KIT FEATURES • Double DIN Radio Provision • Stacked ISO Mount Units Provision • Bonus Display Replacement Pocket KIT COMPONENTS • A) Radio Housing • B) Double DIN Brackets • C) Double DIN Trim plate •D) Display Replacement Pocket • E) Display Retention Brackets • F) (2) 3/8” #10 Bolts and (2) #10 Nuts • G) (2) PC-7503 Panel Clips B F C G A D E WIRING AND ANTENNA CONNECTIONS (Sold Separately) Wiring Harness: • 70-7903
PAGE 2
95-7504 TABLE OF CONTENTS Dash Disassembly - Mazda 3 2004-2009 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - Display Brackets/Pocket Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - Stacked ISO Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
95-7504 DASH DISASSEMBLY MAZDA 3 2004-2009 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove display trim panel above radio. Tip: Open glove box and start in middle of panel working towards drivers side first because last connection on far passenger side is a hook. (Figure A) HOOK 3 Remove (2) Phillips screws exposed at top of radio then unclip and remove radio. Note: Display is attached to radio brackets and will be removed at same time as radio.
PAGE 4
95-7504 DISPLAY POCKET ASSEMBLY DISPLAY BRACKETS/POCKET ASSEMBLY MAZDA 3 2004-2009 AUTOMATIC CLIMATE CONTROL VEHICLES A 1 Using the (2) 3/8” #10 bolts and (2) #10 nuts attach the display retention brackets to the display unit. 2 Remove the (2) Phillips screws in the sub dash. (Figure A) 3 Secure the display unit into the sub dash using the screws removed in the previous step.
PAGE 5
95-7504 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure A) 2 Slide the Double DIN radio into the bracket/radio housing assembly and secure the radio to the assembly using the screws supplied with the radio. Snap the trim plate onto the front of the radio housing. (Figure B) B 3 Attach the (2) PC-7503 panel clips to the rear of the radio housing.
PAGE 6
95-7504 KIT ASSEMBLY STACKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. 1 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure A) A 2 Slide the stacked ISO units into the bracket/radio housing assembly and secure the units to the kit using the screws supplied with the units. Snap the trim plate onto the front of the radio housing. (Figure B) 3 Attach the (2) PC-7503 panel clips to the rear of the radio housing.
PAGE 7
95-7504 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.
PAGE 8
FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. METRA / EIA WIRING CODE 12V Ignition / Acc. . . . . . . . . . Red Right Front (+) . . . . . . . . . . . . Gray 12V Batt / Memory. . . . . . . . . Yellow Right Front (-). . . . . . . . . . .