User Guide

ManualsBrandsMetra Electronics ManualsGuitar95-7951

INSTALLATION INSTRUCTIONS FOR PART 95-7951

95-7951

APPLICATIONS

CHEVROLET

Aveo 2004-2006

Aveo Hatchback-2007

SUZUKI

Forenza 2004-2008

Reno 2005-2008

Verona 2004-2007

PONTIAC

G3 Hatchback-2007

KIT FEATURES

• Double DIN Radio Provision

• Stacked ISO Mount Units Provision

A) Double DIN Trim Plate • B) Double DIN Brackets

KIT COMPONENTS

TOOLS REQUIRED:

1-800-221-0932

www.metraonline.com

Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver

WIRING AND ANTENNA CONNECTIONS

(Sold Separately)

Wiring Harness:

• 70-2105 - GM harness 2006-up

• 70-8405 - GM/Suzuki/Daewoo harness 1999-up

Antenna Adapter:

• 40-CR10 - Chryler antenna adapter 2002-up

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 95-7951 APPLICATIONS CHEVROLET Aveo 2004-2006 Aveo Hatchback-2007 SUZUKI Forenza 2004-2008 Reno 2005-2008 Verona 2004-2007 PONTIAC G3 Hatchback-2007 95-7951 KIT FEATURES • Double DIN Radio Provision • Stacked ISO Mount Units Provision KIT COMPONENTS A) Double DIN Trim Plate • B) Double DIN Brackets A B WIRING AND ANTENNA CONNECTIONS (Sold Separately) Wiring Harness: • 70-2105 - GM harness 2006-up • 70-8405 - GM/Suzuki/Daewoo harness 1999-up Antenna Adapter: • 40-C
PAGE 2
95-7951 TABLE OF CONTENTS Dash Disassembly - Chevrolet Aveo Hatchback 2007 . . . . . . . . . . . . . . . . . . . . . . . . . . .1 - Chevrolet Aveo 2004-2006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 - Suzuki Forenza 2004-2008 / Suzuki Reno 2005-2008 . . . . . . . . 2 - Suzuki Verona 2004-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - Pontiac G3 Hatchback 2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
95-7951 DASH DISASSEMBLY CHEVROLET AVEO 2004-2006 CHEVROLET AVEO HATCHBACK 2007 PONTIAC G3 HATCHBACK 2007 1 Disconnect the negative battery terminal to prevent an accidental short circuit. A 2 Unclip and remove the trim panels from both sides of radio/climate controls. (Figure A) 3 Remove (4) Phillips screws securing the radio. Unplug and remove radio. (Figure B) Continue to kit assembly.
PAGE 4
95-7951 DASH DISASSEMBLY SUZUKI FORENZA 2004-2008 SUZUKI RENO 2005-2008 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Disconnect air selector cable on driver’s side of center console behind dash above accelerator pedal. (Figure A & B) 3 Open glove box and remove (5) Phillips screws ((3) on top and (2) on bottom) then remove entire glove box. B 4 Disconnect temperature selector cable on passenger side of center console behind glove box.
PAGE 5
95-7951 DASH DISASSEMBLY SUZUKI VERONA 2004-2007 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the trim panel surrounding the radio. (Figure A) 3 Remove (4) Phillips screws from radio. Unplug and remove radio. (Figure B) Continue to kit assembly.
PAGE 6
95-7951 KIT ASSEMBLY DOUBLE DIN MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. NOTE: For the Chevrolet Aveo 2004-06, Chevrolet Aveo Hatchback 2007, Pontiac G3 Hatchback 2007 and Suzuki Verona 2004-07, cut and remove front lower mounting tabs from the Double DIN trim plate (Figure A). For the Suzuki Forenza 2004-07 and the Suzuki Reno 2005-07, cut the rear lower mounting tabs (Figure B).
PAGE 7
95-7951 KIT ASSEMBLY STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. NOTE: For the Chevrolet Aveo 2004-06, Chevrolet Aveo Hatchback 2007, Pontiac G3 Hatchback 2007 and Suzuki Verona 2004-07, cut and remove front lower mounting tabs from the Double DIN trim plate (Figure A). For the Suzuki Forenza 2004-07 and the Suzuki Reno 2005-07, cut the rear lower mounting tabs (Figure B).
PAGE 8
95-7951 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation.