Automobile Accessories User Manual

ManualsBrandsMetra Electronics ManualsAutomobile Accessories95-9012

INSTALLATION INSTRUCTIONS FOR PART 95-9012

95-9012

KIT FEATURES

• Double DIN Head Unit Provision

• Stacked ISO DIN Head Unit Provision

A) Radio Housing • B) (8) Phillips screws

KIT COMPONENTS

• Small Flat Blade Screwdriver • Panel Removal Tool

• 86-9001 Radio Removal Tools (2 sets)

1-800-221-0932

www.metraonline.com

TOOLS REQUIRED:

APPLICATIONS

WIRING AND ANTENNA CONNECTIONS (Sold Separately)

• 70-1784 VW harness 1998-2001

• XSVI-9003-NAV VW Interface 2003-up

Antenna adapter:

• 40-EU55-adapter for amplified antenna 2002-up

• 40-VW53 adapter for amplified antenna 1998-01

•GOLF 1999-2006

•GTI 1999-2005

•JETTA 1999-2005

(Excluding NEW JETTA 2005)

•PASSAT 2000-2005

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 95-9012 APPLICATIONS •GOLF 1999-2006 •GTI 1999-2005 •JETTA 1999-2005 (Excluding NEW JETTA 2005) •PASSAT 2000-2005 95-9012 KIT FEATURES • Double DIN Head Unit Provision • Stacked ISO DIN Head Unit Provision KIT COMPONENTS A) Radio Housing • B) (8) Phillips screws B A WIRING AND ANTENNA CONNECTIONS (Sold Separately) • 70-1784 VW harness 1998-2001 • XSVI-9003-NAV VW Interface 2003-up Antenna adapter: • 40-EU55-adapter for amplified antenna 2002-up • 40-VW53 adapter for
PAGE 2
95-9012 TABLE OF CONTENTS Dash Disassembly - Golf 1999-2006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - GTI 1999-2005 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - JETTA 1999-2005 (Excluding NEW JETTA 2005) . . . . . . . . . . . . . . . . . . . . . . . 1 - PASSAT 2000-2005 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
95-9012 DASH DISASSEMBLY •GOLF 1999-2006 •GTI 1999-2005 •JETTA 1999-2005 (Excluding NEW JETTA 2005) •PASSAT 2000-2005 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Insert the long ends of the 86-9001 into the slots on the factory radio and pull out to remove. Note: Flat edge of key should point outward. (Figure A) 3 For single DIN radios with the pocket, remove the radio and pocket, then pull out on the plastic tray separating the dash cavity.
PAGE 4
95-9012 KIT ASSEMBLY/ FINAL ASSEMBLY DOUBLE DIN HEAD UNIT PROVISION/ ISO STACKED HEAD UNIT PROVISION A 1 Slide the DDIN radio unit into the DDIN bracket/radio housing assembly and secure the unit to the kit using the (8) Phillips screws supplied with the kit. (Figure A) 2 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation.