INSTALLATION INSTRUCTIONS FOR PART 99-1003 APPLICATIONS KIA Rio 2001 Sephia 1995-2001 Spectra 2000-2001 Sportage 1995-2003 99-1003 KIT FEATURES • DIN Radio Provision KIT COMPONENTS A) Radio Housing #1 • B) Radio Housing #2 • C) Mounting Brackets • D) (4) Captive Studs • E) (4) Pal Nuts C B A E D WIRING AND ANTENNA CONNECTIONS (Sold Separately) • 70-1003 - KIA Harness 1995-02 • Antenna Adapter N/R TOOLS REQUIRED: Panel Removal Tool • Cutting Tool • Phillips Screwdriver 1-800-221-0932 www.
99-1003 TABLE OF CONTENTS Dash Disassembly - Kia Rio 2001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - Sephia 1995-1997 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - Sephia 1998-2001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - Spectra 2000-2001. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
99-1003 DASH DISASSEMBLY RIO 2001 OFF *Note: Refer also to the instructions included with the aftermarket radio. A 1 Disconnect the negative batteryterminal to prevent an accidental short circuit. A/C 2 Remove ashtray and (1) Phillips head screw inside ashtray cavity. (Figure A) 3 Remove knob from climate control slide lever. (Figure B) 4 Unsnap and remove radio/climate control trim panel. (Figure C) B OFF 5 Remove (4) Phillips head screws securing the radio. Unplug and remove the radio.
99-1003 DASH DISASSEMBLY SEPHIA 1995-1997 *Note: Refer also to the instructions included with the aftermarket radio. 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove plastic screw cover to the left of the coin tray and remove the Phillips head screw from behind cover. 3 Remove switch blank to the far right of the switch panel and remove the Phillips head screw from behind switch blank. 4 Unclip and remove dash trim panel.
99-1003 DASH DISASSEMBLY SEPHIA 1998-2001 SPECTRA 2000-2001 *Note: Refer also to the instructions included with the aftermarket radio. 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove (1) Phillips head screw from above instrument cluster. 3 Unclip and remove dash trim panel. 4 Remove (4) Phillips head screws securing the radio. Unplug and remove the radio. Continue to kit preparation.
99-1003 DASH DISASSEMBLY SPORTAGE 1995-1997 *Note: Refer also to the instructions included with the aftermarket radio. 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove ashtray and (2) Phillips head screws inside ashtray cavity. 3 Unclip and remove dash trim panel. 4 Remove (4) Phillips head screws securing the radio. Unplug and remove the radio. Continue to kit preparation.
99-1003 DASH DISASSEMBLY SPORTAGE 1998-2000 *Note: Refer also to the instructions included with the aftermarket radio. 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove dash trim panel. 3 Remove (4) Phillips head screws securing the radio. Unplug and remove the radio. Continue to kit preparation.
99-1003 DASH DISASSEMBLY SPORTAGE 2001-2003 *Note: Refer also to the instructions included with the aftermarket radio. 1 Disconnect the negative battery terminal to prevent an accidental short circuit. A 2 Unclip and remove climate control/vent trim panel. (Figure A) 3 Remove screw covers from trim panel below steering column and remove screws from behind covers. Lower the trim panel (it is not necessary to remove the panel).
9-1003 KIT PREPARATION KIT ASSEMBLY PREPARATION *Note: Refer also to the instructions included with the aftermarket radio. SEPHIA 1998-2001 SPECTRA 2000-2001 RIO 2001 SEPHIA 1995-1997 Cut and remove mounting tabs “B” from Radio Housing #2. (The tabs can be identified by the letter stamped on the back of each tab.) (Figure A) Cut and remove mounting tabs “B” from Radio Housing #1. (The tabs can be identified by the letter stamped on the back of each tab.
99-1003 KIT ASSEMBLY DIN MOUNT RADIO *Note: Refer also to the instructions included with the aftermarket radio. A NOTE: For Sportage 1995-97 and 1998-03 secure the Mounting Brackets to the Radio Housing with (4) Captive Studs and (4) Pal Nuts. (Figure A) 1 Slide the DIN cage into the radio housing and secure by bending the metal locking tabs outward. (Figure B) 2 Slide the radio into the DIN cage/housing assembly until it snaps into place. (Figure C) Continue to final assembly.
99-1003 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.
99-1003 INSTRUCTIONS 1-800-221-0932 www.metraonline.com Rev.
