Car Stereo System - Car Radio User Manual

ManualsBrandsMetra Electronics ManualseBook Reader99-2008

INSTALLATION INSTRUCTIONS FOR PART 99-2008

99-2008

APPLICATIONS

Cadillac DTS 2006-2010

Cadillac SRX 2007-2009

KIT FEATURES

• DIN Radio Provisiion with Pocket

• ISO Mount Radio Provisiion with Pocket

• Double DIN Radio Provisiion

• Stacked ISO Mount Units Provisiion

A) Radio Housing • B) ISO Trim Plate • C) ISO Brackets • D) Double DIN Trim Plate

• E) Double DIN Brackets • F) Pocket

KIT COMPONENTS

1-800-221-0932

www.metraonline.com

TOOLS REQUIRED:

WIRING

AND ANTENNA CONNECTIONS

(Sold Separately)

• GMOS-LAN-01 - GM LAN Interface

2006-up

• GMOS-LAN-02 - GM LAN Amplified-

Interface 2006-up

• GMOS-LAN-05 - GM Digital LAN Amp

Interface With Onstar 2007-up

• Antenna Adapter:

40-CR10 - Chrysler/GM Antenna

Adapter 2002-up

Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver • Socket Set

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-2008 APPLICATIONS Cadillac DTS 2006-2010 Cadillac SRX 2007-2009 99-2008 KIT FEATURES • DIN Radio Provisiion with Pocket • ISO Mount Radio Provisiion with Pocket • Double DIN Radio Provisiion • Stacked ISO Mount Units Provisiion KIT COMPONENTS A) Radio Housing • B) ISO Trim Plate • C) ISO Brackets • D) Double DIN Trim Plate • E) Double DIN Brackets • F) Pocket B C A E F D WIRING AND ANTENNA CONNECTIONS (Sold Separately) • GMOS-LAN-01 - GM LAN Interface 2006-up •
PAGE 2
99-2008 TABLE OF CONTENTS Dash Disassembly Chevrolet - Cadillac DTS 2006-2010. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 - Cadillac SRX 2007 -2009 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Kit Assembly DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 ISO Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . 4 Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
99-2008 DASH DISASSEMBLY Cadillac DTS 2006-2010 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the trim panel around the radio, climate controls and ac vents and above glove box. (Figure A) 3 Remove (4) 9/32” screws securing the a/c vent panel. Unplug and remove the panel. (Figure B) B 4 Remove (4) 9/32” screws securing the climate controls. Unplug and remove the climate controls. (Figure C) 5 Remove (4) 9/32” screws securing the radio.
PAGE 4
99-2008 DASH DISASSEMBLY Cadillac SRX 2007-2009 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove trim piece between shifter and cup holders. (Figure A 3 Unclip and remove the trim panel around the radio, climate controls, ac vents and front half of center console. (Figure B) B 4 Remove (3) 9/32” screws securing the a/c vent panel and remove the panel. (Figure C) 5 Remove (4) 9/32” screws securing the climate controls.
PAGE 5
99-2008 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) 3 Snap the pocket into the housing. (Figure C) B Continue to final assembly.
PAGE 6
99-2008 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Snap the trim plate onto the front of the radio housing. (Figure B) 4 Snap the pocket into the housing. (Figure C) B Continue to final assembly.
PAGE 7
99-2008 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 3 Slide the Double DIN radio or stacked ISO mount units into the bracket/radio housing assembly then secure to the assembly using the screws supplied with the radio or ISO mount units.
PAGE 8
99-2008 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation.