User Manual

ManualsBrandsMetra Electronics ManualsCar & Vehicle ElectronicsSingle/Double DIN Stereo Installation Dash Kit for 2013-Up Chevy Spark (Matte Black)

INSTALLATION INSTRUCTIONS FOR PART 99-3309B-LC

APPLICATIONS

METRA. The World’s best kits.

™

metraonline.com1-800-221-0932

REV. 4/19/2013 INST99-3309B-LC

CAUTION: Metra recommends disconnecting the

negative battery terminal before beginning any

installation. All accessories, switches, and especially

air bag indicator lights must be plugged in before

reconnecting the battery or cycling the ignition.

NOTE: Refer to the instructions included with the

aftermarket radio.

• A) Radio Trim Panel • B) Radio Brackets • C) Pocket • D) (4) #8 x 3/8” Phillips screws • E) (10) White Plastic Panel Clips

• F) Interface • G) 4-pin to 44-pin harness

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • Interface included Antenna Adapter: • 40-EU55 antenna adapter

• Panel removal tool • Phillips screwdriver

• Small flat-blade screwdriver

TOOLS REQUIRED

Chevrolet Spark 2013-up

99-3309B-LC

B C

F G

D E

Table of Contents

Dash Disassembly

– Chevy Spark 2013-up .......................................... 2

Kit Assembly

– ISO radio provision with pocket ............................ 3

– DDIN radio provision ............................................ 4

Interface Installation

– Wire connections ................................................. 5

• ISO DIN and DDIN radio provisions

• Painted Matte Black

• AXXESS Interface included

•Providesaccessory(12volt3amp)andretained

 accessorypower

•Retainsallwarningchimes

Summary of content (16 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-3309B-LC APPLICATIONS Table of Contents Chevrolet Spark 2013-up 99-3309B-LC Dash Disassembly – Chevy Spark 2013-up .......................................... 2 REV. 4/19/2013 INST99-3309B-LC KIT FEATURES • ISO DIN and DDIN radio provisions • Painted Matte Black • AXXESS Interface included • Provides accessory (12 volt 3 amp) and retained accessory power • Retains all warning chimes Kit Assembly – ISO radio provision with pocket ............................
PAGE 2
99-3309B-LC Dash Disassembly 1. Unclip and remove the radio trim panel. (Figure A) 2. Remove (4) Phillips screws securing the factory radio and remove from dash. (Figure B) Step 5 3. Unclip and remove the vents from the factory panel. (Figure C) Step 5 4. Unclip and remove the hazard button from the trim panel. (Figure C) 5. Remove (5) Phillips screws securing the upper display shroud from the factory panel.
PAGE 3
99-3309B-LC Kit Assembly ISO DIN radio provisions 1. Attach the factory vents and hazard button to the Metra trim panel. (Figure A) 2. Attach the upper display shroud the Metra trim panel with the factory screws. (Figure A) 3. Attach the provided (10) panel clips to the legs of the Metra trim panel. 4. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 5.
PAGE 4
99-3309B-LC Kit Assembly DDIN radio provisions 1. Attach the factory vents and hazard button to the Metra trim panel. (Figure A) 2. Attach the upper display shroud the Metra trim panel with the factory screws. (Figure A) 3. Attach the provided (10) panel clips to the legs of the Metra trim panel. 4. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation.
PAGE 5
99-3309B-LC Wire connections to be made CAUTION: Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition.Note: Refer to the instructions included with the aftermarket radio. 6. Connect the White/Black wire to the radios left front (-) speaker wire.
PAGE 6
99-3309B-LC Notes
PAGE 7
99-3309B-LC Notes
PAGE 8
INSTALLATION INSTRUCTIONS FOR PART 99-3309B-LC REV. 4/19/2013 INST99-3309B-LC KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians METRA. The World’s best kits.™ 1-800-221-0932 metraonline.
PAGE 9
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-3309B-LC AplicAciones Indice Chevrolet Spark 2013 y mas 99-3309B-LC Desmontaje del tablero – Chevrolet Spark 2013 y mas ................................ 2 REV.
PAGE 10
99-3309B-LC Desmontaje del tablero 1. Desenganche y quite el panel de la moldura del radio. (Figura A) 2. Desenganche y quite las rejillas del aire acondicionado del panel de fábrica. (Figura B) Paso 5 3. Desenganche y retire el botón de las luces intermitentes del panel de la moldura. (Figura C) 4. Quite los (5) tornillos Phillips que sujetan la tapa de la pantalla superior del panel de fábrica. (Figura C) Paso 5 Paso 3 (Figura A) 5. Quite el radio de fábrica.
PAGE 11
99-3309B-LC Ensamble del kit Provisiones de unidad central ISO DIN. 1. Instale las rejillas de fábrica y el botón de las luces intermitentes en el panel de la moldura de Metra. (Figura A) 2. Instale la tapa de la pantalla superior al panel de la moldura Metra con los tornillos de fábrica. (Figura A) Paso 2 3. Instale los (10) ganchos del panel provistos en las patas del panel de la moldura Metra. 4. Localice el arnés de cables de fábrica en el tablero.
PAGE 12
99-3309B-LC Ensamble del kit Provisiones de unidad central DDIN. 1. Instale las rejillas de fábrica y el botón de las luces intermitentes en el panel de la moldura de Metra. (Figura A) 2. Instale la tapa de la pantalla superior al panel de la moldura Metra con los tornillos de fábrica. (Figura A) 3. Instale los (10) ganchos del panel provistos en las patas del panel de la moldura Metra. 4. Localice el arnés de cables de fábrica en el tablero.
PAGE 13
99-3309B-LC Conexiones de cables que se deben hacer PRECAUCIÓN: Metra recomienda desconectar el terminal negativo de la batería antes de comenzar cualquier instalación. Todos los accesorios, interruptores y, especialmente, las luces indicadoras de airbag deben estar enchufados antes de volver a conectar la batería o comenzar el ciclo de ignición. Nota: Remítase a las instrucciones incluidas con el radio de postventa.
PAGE 14
99-3309B-LC Notas 6
PAGE 15
99-3309B-LC Notas 7
PAGE 16
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-3309B-LC REV. 4/19/2013 INST99-3309B-LC EL CONOCIMIENTO ESOWER PODER K NOWLEDGE IS P Mejore sus habilidades de instalación y fabricación Enhance your installation and fabrication skills by enrolling in the en most recognized and respected inscribiéndose la escuela de dispositivos electrónicos mobile school in our industry. móvileselectronics más reconocida y respetada de nuestra industria. Log onto www.installerinstitute.com or call Regístrese en www.