installation instructions for Part 99-6507 APPLICATIONS CHRYSLER 300 2005-2007 Aspen 2007 PT Cruiser 2006-2009 JEEP Commander 2006-2007 Compass 2007-2008 Grand Cherokee 2005-2007 Patriot 2007-2008 DODGE Caliber 2007-2008 Charger 2005-2007 Dakota 2005-2007 Durango 2004-2007 Magnum 2005-2007 Ram 2006-2008 Ram 2500/3500 2009 MITSUBISHI Raider 2006-2007 NOTE: NON NAV MODELS ONLY 99-6507 KIT FEATURES • DIN Radio Provision with Pocket • ISO DIN Radio Provision with Pocket KIT COMPONENTS A) Radio Housing •
99-6507 taBlE of contEnts Dash Disassembly - Chrysler Aspen 2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - Dodge Dakota 2005-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - Dodge Durango 2004-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - Dodge Charger 2005-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - Dodge Magnum 2005-2007 . . .
99-6507 DasH DisassEMBlY cHrYslEr asPEn 2007 DoDgE Dakota 2005-2007 DoDgE Durango 2004-2007 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove (2) 7MM screws from the inside of the pocket facing upward. (Figure A) 3 Unclip and remove the entire trim panel surrounding the radio and climate controls. (Figure B) B 4 Remove (4) 7MM screws securing radio. Unplug and remove radio.(Figure C) C 5 Continue to kit assembly.
99-6507 DasH DisassEMBlY DoDgE cHargEr 2005-2007 DoDgE MagnuM 2005-2007 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove entire panel surrounding radio and climate controls, including a/c vents. (Figure A) B 3 Remove (4) 7MM screws securing radio. Unplug and remove radio. (Figure B) 4 Continue to kit assembly.
99-6507 DasH DisassEMBlY cHrYslEr 300 2005-2007 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove entire panel surrounding radio and climate controls, including a/c vents and clock. (Figure A) 3 Remove (4) 7MM screws securing radio. Unplug and remove radio. (Figure B) B 4 Continue to kit assembly.
99-6507 DasH DisassEMBlY DoDgE raM 2006-2008 witHout cEntEr consolE A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Open cup holder and remove (2) Phillips screws facing up on front edge of radio/climate control panel. (Figure A) B 3 Unclip and remove entire panel surrounding radio and climate controls, including a/c vents. (Figure B) 4 Remove (4) 7MM screws securing radio. Unplug and remove radio. 5 Continue to kit assembly.
99-6507 DasH DisassEMBlY DoDgE raM 2006-2008 witH Mini cEntEr consolE 1 2 A Disconnect the negative battery terminal to prevent an accidental short circuit. If vehicle has floor shifter, remove shifter knob. 3 Remove center console inserts, if present. (Figure A) 4 Remove screws securing the rear center console to the floor panel. Lift up on the rear center console to clear the gear shift lever, if present. (Figure B) B 5 Remove screws securing the front center console to the floor panel.
99-6507 DasH DisassEMBlY DoDgE raM 2006-2008 witH full cEntEr consolE A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 If vehicle has floor shifter, remove shifter knob. 3 Unsnap and remove console front top cover (closest to the dash). (Figure A) 4 Remove two 8 mm screws from under console cover (previously removed). Remove front section of console. (Figure B) 5 Loosen two 8 mm screws at bottom of dash. Unsnap lower panel.
9-6507 DasH DisassEMBlY DoDgE caliBEr 2007-2008 JEEP coMPass 2007-2008 JEEP Patriot 2007-2008 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unsnap and move shifter trim to the side. (Figure A) 3 1 (Compass and Patriot only) Unspap and remove top center dash panel above AC vents. Unsnap center dash trim panel (do not remove until climate controls are removed).
99-6507 DasH DisassEMBlY JEEP granD cHErokEE 2005-2007 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unsnap and remove panel from around radio including the vent on each side. (Figure A) B 3 Remove (4) 7MM screws securing radio. Unplug and remove radio. (Figure B) 4 Continue to kit assembly.
99-6507 DasH DisassEMBlY JEEP coMManDEr 2006-2007 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove the (16) screws securing the radio trim panel. (Figure A) A 4 screws 4 screws 4 screws 3 Unclip and remove the entire radio trim panel. (Figure B) B 4 Remove (4) 7MM screws securing radio. Unplug and remove radio. 5 Continue to kit assembly.
99-6507 DasH DisassEMBlY cHrYslEr Pt cruisEr 2006-2009 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove (2) screws from inside air vents on center dash panel. (Figure A) 3 Unsnap center dash panel (do not remove until climate controls are removed). (Figure A) 4 Remove (4) Phillips screws holding climate control panel to backside of the center dash panel. 5 Remove (4) Phillips screws holding climate control panel to backside of the center dash panel.
99-6507 DasH DisassEMBlY MitsuBisHi raiDEr 2006-2007 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unsnap and remove center dash panel. (Figure A) 3 Remove (4) 7MM screws securing radio. Unplug and remove radio. 4 Continue to kit assembly.
99-6507 kit assEMBlY Din raDio Provision witH PockEt A NOTE: You will need to remove the aftermarket radio’s trim ring if equipped. 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) B 2 Slide the after-market head unit into the cage and secure. (Figure B) C 3 Using the alignment pins on the trim plates & the corresponding holes in the housing, attach the upper trim plate and the lower trim plate supplied with the kit.
99-6507 kit assEMBlY iso raDio Provision witH PockEt A NOTE: You will need to remove the aftermarket radio’s trim ring if equipped. 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. Figure A 2 Slide the radio into the opening until it snaps into place. Figure B 3 Using the alignment pins on the trim plates & the corresponding holes in the housing, attach the upper trim plate and the lower trim plate supplied with the kit. B Figure B 4 Continue to Final Assembly.
99-6507 final assEMBlY final assEMBlY A B C A) Strip wire ends back 1/2" B) Twist ends together C) Solder D) Tape D 1 2 3 4 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Secure the kit into the sub dash using the (4) 7mm screws that secured the factory radio.
