DODGE Stealth 1991-96 / MITSUBISHI 3000GT 1991-98 1 EAGLE Summit (wg) 1992-96 / MITSUBISHI Expo 1992-95 PLYMOUTH Colt Vista 1992-94 2 "E" 1 2 "F" "E" "E" "F" Disconnect the negative battery terminal to prevent an accidental short circuit. Using a panel removal tool, pry out on the radio trim bezel and remove. Remove (4) screws securing the factory head unit and disconnect the wiring. "F" Cut and remove mounting tabs "A" and "B" on the Radio Housing.
EAGLE Talon / MITSUBISHI Eclipse 1995-98 EAGLE Talon / MITSUBISHI Eclipse PLYMOUTH Laser 1990-94 1 1 2 "B" Radio trim bezel 2 Center console "B" Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip the radio trim bezel (the factory pocket will be attached). Remove (4) screws securing the factory head unit and disconnect the wiring. Cut and remove all mounting tabs on the Radio Housing EXCEPT tabs "B".
MITSUBISHI Diamante 1994-96 1 2 MITSUBISHI Eclipse 2000-01 1 Fig. A 2 “A” “A” “A” Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (2) Phillips screws from each side of the gear shifter console. Remove (2) Phillips screws from the top of the console (under the ashtray). Lift the console out and remove (2) Phillips screws exposed at the base of the dash trim bezel. Pull out on the bottom of the dash trim bezel, disconnect the wiring and remove the bezel.
MITSUBISHI Galant 1994-98 1 MITSUBISHI Mirage 1997-00 1 2 2 "C" "D" "D" "C" "D" Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip the gear shifter trim panel and remove. Remove (2) Phillips screws exposed at the base of the dash trim bezel. Unclip the dash trim bezel. Remove (4) Phillips screws securing the factory head unit and disconnect the wiring. Cut and remove mounting tabs "A" and "B" on the Radio Housing.
MITSUBISHI Montero 1992-96 1 2 MITSUBISHI Montero Sport 2000-02 "B" 1 2 "B" "B" "B" "X" Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (2) screws above the climate controls. Unclip the bottom of the dash trim bezel and remove the bezel. Remove (4) screws securing the factory head unit and disconnect the wiring. Cut and remove mounting tabs "A" and "B" on the Radio Housing. Cut and remove all mounting tabs on Bracket Set #1 EXCEPT tabs "B".
5 ALL VEHICLES Fig. A 4 Fig. A Fig. B Fig. B Fig. C Fig. C Fig. D 2-SHAFT HEAD UNITS: Snap the Shaft Supports into the Radio Housing. Slide the aftermarket head unit into the kit and secure with shaft nuts. (see Fig. A). DIN HEAD UNITS: For dash trim bezels with an UNDIVIDED radio opening, slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. Slide the aftermarket head unit into the cage until secure.
7 Fig. B ¼" Fig. A Fig. C TALON 1995-98, ECLIPSE 1995-98, COLT, SUMMIT, MIRAGE, STEALTH, 3000GT, DIAMANTE, GALANT, MONTERO: No cutting of the dash or dash trim bezel is required. Skip to the Wiring Preparation in step #8. TALON, ECLIPSE, LASER 1990-94: If keeping the factory pocket is desired, cut and remove the inside half of each pocket mount located on the back of the dash trim bezel. (see Fig. A) SUMMIT (wagon), EXPO, COLT VISTA: Cut and remove ¼" from the top edge of the dash cavity opening.
