Car Stereo System - Car Radio User Manual

ManualsBrandsMetra Electronics ManualsSpeaker99-7011

INSTALLATION INSTRUCTIONS FOR PART 99-7011

99-7011

MITSUBISHI Lancer

2008-2010

KIT FEATURES

• DIN Radio Provision with Pocket

• ISO Mount Radio Provision with Pocket

• Double DIN Radio Provision

• Stacked ISO Mount Units Provision

• Painted to Match Factory

• A) Radio Housing • B) ISO Brackets • C) Trim Plate • D) Double DIN Brackets

• E) Double DIN Trim Plate • F) Snap in Pocket

KIT COMPONENTS

Phillips Screwdriver/ Panel Removal Tool

• Cutting Tool

1-800-221-0932

www.metraonline.com

TOOLS REQUIRED:

APPLICATIONS

WIRING AND ANTENNA CONNECTIONS: (Sold Separately)

Harness

• MITO-02 - Mitsubishi amp interface harness 2007-up

• 70-7005 - Mitsubishi harness 2007-up

Antenna Adapter:

• No antenna adapter required

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7011 APPLICATIONS MITSUBISHI Lancer 2008-2010 99-7011 KIT FEATURES • DIN Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • Double DIN Radio Provision • Stacked ISO Mount Units Provision • Painted to Match Factory KIT COMPONENTS • A) Radio Housing • B) ISO Brackets • C) Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate • F) Snap in Pocket B C A D E WIRING AND ANTENNA CONNECTIONS: (Sold Separately) Harness: • MITO-02 - Mitsubishi
PAGE 2
99-7011 TABLE OF CONTENTS Dash Disassembly - Mitsubishi Lancer 2008-2010 . . . . . . . . . . . . . . . . . . . . . . . . 1,2 Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 5 - Double DIN Radio Provision/Stacked ISO Mount Units Provision . . . . . .
PAGE 3
99-7011 DASH DISASSEMBLY MITSUBISHI LANCER 2008-2010 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Open the glove box and remove (1) Phillips screw from the panel to the right of the glove box door. Unclip and remove the panel. (Figure A) 3 Remove (1) Phillips screw from the panel above the glove box then unclip and remove the panel. (Figure B) B Continued on page 2.
PAGE 4
99-7011 DASH DISASSEMBLY MITSUBISHI LANCER 2008-2010 C 4 Unclip the radio switch panel including the hazard switch assembly. Unplug hazard switch assembly and remove panel. (Figure C) 5 Remove (4) Phillips screws securing the radio chassis. Unplug and remove chassis. PASSENGER AIRBAG OFF 6 Remove (3) Phillips screws securing the hazard switch assembly to the factory radio switch panel. Unclip and remove the switch.
PAGE 5
99-7011 KIT PREPARATION MITSUBISHI LANCER 2008-2010 1 Secure the hazard switch assembly into the radio housing using the factory hardware. Snap the a/c vents into the radio housing. (Figure A) 2 Use the (7) plastic factory clips previously removed during dash disassembly and attach where shown.
PAGE 6
99-7011 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) 3 Snap the pocket into the radio housing. (Figure C) Continue to final assembly.
PAGE 7
99-7011 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Snap the trim plate onto the front of the radio housing. (Figure B) 4 Snap the Pocket into the radio housing. (Figure C) B Continue to final assembly.
PAGE 8
99-7011 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 3 Slide the Double DIN or stacked ISO mount unit(s) into the bracket/radio housing assembly and secure the unit(s) to the assembly using the screws supplied with the unit(s).
PAGE 9
9-7011 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation.
PAGE 10
99-7011 NOTES 8
PAGE 11
99-7011 NOTES 9
PAGE 12
99-7011 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV.