Car Stereo System User Manual

ManualsBrandsMetra Electronics ManualsCar Stereo System99-7328

INSTALLATION INSTRUCTIONS FOR PART 99-7328

99-7328

KIT FEATURES

• Recessed DIN Radio Provision with Pocket

• ISO Mount Radio Provision with Pocket

A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate

KIT COMPONENTS

Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver

1-800-221-0932

www.metraonline.com

APPLICATIONS

KIA Sorento

2007-2009

B C

WIRING AND ANTENNA CONNECTIONS (Sold Separately)

Harness:

• 70-7302 - Hyundai harness 2007-up

Antenna Adapter:

• Not required

TOOLS REQUIRED:

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7328 APPLICATIONS KIA Sorento 2007-2009 99-7328 KIT FEATURES • Recessed DIN Radio Provision with Pocket • ISO Mount Radio Provision with Pocket KIT COMPONENTS A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate B A C WIRING AND ANTENNA CONNECTIONS (Sold Separately) Harness: • 70-7302 - Hyundai harness 2007-up Antenna Adapter: • Not required TOOLS REQUIRED: Flat Blade Screwdriver/ Panel Removal Tool • Phillips Screwdriver 1-800-221-0932 www.metraonline.
PAGE 2
99-7328 TABLE OF CONTENTS Dash Disassembly - KIA Sorento 2007-2009 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - Recessed DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . 2 - ISO Mount Radio Provision with Pocket . . . . . . . . . . .. . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
99-7328 DASH DISASSEMBLY KIA SORENTO 2007-2009 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the side trim panels. (Tip: start at the bottom of the panels) (Figure A) 3 Remove (2) Phillips head screws securing the radio trim panel. Unplug and remove panel. (Figure B) 4 Remove (2) Phillips head screws securing the vent panels then unclip and remove the (2) vent panels. (Figure C) B 5 Remove (4) Phillips screws securing the radio.
PAGE 4
99-7328 KIT ASSEMBLY RECESSED DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the radio housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the radio into the DIN cage/housing assembly until it snaps into place. (Figure B) Continue to final assembly.
PAGE 5
99-7328 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Align the holes from the ISO snap in brackets with the holes in the side of the radio and mount the brackets to the radio using screws supplied with the radio. (Figure A) 2 Slide the radio/bracket assembly into the radio housing until the assembly snaps into place. (Figure B) 3 Snap the ISO Trim-plate onto the Radio and housing assembly.
PAGE 6
99-7328 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.
PAGE 7
99-7328 NOTES 5
PAGE 8
99-7328 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV.