Automobile Accessories User Manual

ManualsBrandsMetra Electronics ManualsAutomobile Accessories99-7423

INSTALLATION INSTRUCTIONS FOR PART 99-7423

99-7423

KIT FEATURES

• DIN Radio Provision with Pocket

• ISO Mount Radio Provision with Pocket

• Double DIN Radio Provision

• Stacked ISO Mount Units Provision

• A) Radio Housing • B) Radio Housing Trim Plate • C) Radio Housing Brackets

• D) Double DIN Trim Plate • E) Double DIN Brackets • F) ISO Brackets • G) Pocket

• H) (2) Climate Control Trim Panels • I) (2) #8 3/8” Screws

Harness & Antenna Connections (sold separately)

• 70-7552 - Nissan Harness 07-up

• 40-NI12 - Nissan Antenna Adapter 07-up

KIT COMPONENTS

Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver • Torx Screwdriver

1-800-221-0932

www.metraonline.com

TOOLS REQUIRED:

APPLICATIONS

NISSAN Altima

2007-2011

H I

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7423 APPLICATIONS NISSAN Altima 2007-2011 99-7423 KIT FEATURES • DIN Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • Double DIN Radio Provision • Stacked ISO Mount Units Provision KIT COMPONENTS • A) Radio Housing • B) Radio Housing Trim Plate • C) Radio Housing Brackets • D) Double DIN Trim Plate • E) Double DIN Brackets • F) ISO Brackets • G) Pocket • H) (2) Climate Control Trim Panels • I) (2) #8 3/8” Screws C B D E F Harness & Antenna
PAGE 2
99-7423 TABLE OF CONTENTS Dash Disassembly - NISSAN Altima 2007 -2011 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - ISO Mount Radio Provision with Pocket . . . . . . . . . . .. . . . . . . . . . . . . . . . . .
PAGE 3
99-7423 DASH DISASSEMBLY NISSAN ALTIMA 2007-2011 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove trim panel between the shifter and the radio/ climate control panel. (Figure A) 3 Remove (2) Phillips screws exposed behind panel below radio/climate control panel. (Figure A) 4 Unclip and remove the climate control vent trim panel then remove (2) Phillips screws exposed behind panel.
PAGE 4
99-7423 KIT PREPARATION NISSAN ALTIMA 2007-2011 A 1 Clip the corresponding climate control trim panel into the radio housing. Note: There are (2) different climate control trim panels. One for auto climate control and one for manual climate control. (Figure A) 2 Attach the (2) radio housing brackets to the climate controls using the factory screws. (Figure B) 3 Attach the bracket/climate control assembly to the radio housing using the (2) #8 3/8” screws supplied with this kit.
PAGE 5
99-7423 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) 3 Attach the radio housing trim plate supplied with the kit to the assembly. 4 Snap in the pocket into the assembly. (Figure C) B Continue to final assembly.
PAGE 6
99-7423 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio with the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Attach the radio housing trim plate supplied with the kit to the assembly. (Figure B) 4 Snap the pocket into the assembly. (Figure C) B Continue to final assembly.
PAGE 7
99-7423 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing assembly. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing assembly. (Figure B) 3 Slide the Double DIN radio into the bracket/radio housing assembly and secure the radio to the assembly using the screws supplied with the radio.
PAGE 8
99-7423 KIT ASSEMBLY STACKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing assembly. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing assembly. (Figure B) 3 Slide the stacked ISO units into the bracket/radio housing assembly and secure the units to the kit using the screws supplied with the units.
PAGE 9
9-7423 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.
PAGE 10
99-7423 NOTES 8
PAGE 11
99-7423 NOTES 9
PAGE 12
99-7423 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV.