Car Stereo System - Auto Radio User Manual

ManualsBrandsMetra Electronics ManualseBook Reader99-7424

INSTALLATION INSTRUCTIONS FOR PART 99-7424

99-7424

APPLICATIONS

Nissan Titan 2008-11

KIT FEATURES

• DIN Radio Provision with Pocket

• ISO Mount Radio Provision with Pocket

• Painted To Match Factory Dash

A) Single DIN Radio Housing • B) ISO Trim Plate • C) ISO Brackets • D) Trim Panel

• E) Two Sided Tape (Not Shown)

KIT COMPONENTS

TOOLS REQUIRED:

Torx T-10 Driver • Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver

1-800-221-0932

www.metraonline.com

Harness & Antenna Connections (sold separately)

• 70-7550 - Nissan Harness 95-up

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7424 APPLICATIONS Nissan Titan 2008-11 99-7424 KIT FEATURES • DIN Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • Painted To Match Factory Dash KIT COMPONENTS A) Single DIN Radio Housing • B) ISO Trim Plate • C) ISO Brackets • D) Trim Panel • E) Two Sided Tape (Not Shown) A B C D Harness & Antenna Connections (sold separately) • 70-7550 - Nissan Harness 95-up TOOLS REQUIRED: Torx T-10 Driver • Small Flat Blade Screwdriver/ Panel Removal Too
PAGE 2
99-7424 TABLE OF CONTENTS Dash Disassembly Nissan Titan 2008-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . 2 Kit Assembly - DIN Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
99-7424 DASH DISASSEMBLY NISSAN Titan 2008-11 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip the entire dash panel including the radio and climate controls. Unplug and remove the panel. (Figure A) 3 Remove (4) Phillips screws securing the radio chassis. Unplug and remove the chassis. (Figure B) B 4 Remove (4) T-10 Torx screws securing the climate controls to the dash panel and remove the controls from the panel.
PAGE 4
99-7424 KIT PREPARATON NISSAN Titan 2008-11 A 1 Attach the climate controls to the Trim Panel using the factory hardware removed during the dash disassembly. (Figure A) 2 Attach the passenger air bag status light assembly to the Trim Panel using the factory hardware removed during the dash disassembly. Also, apply to air bag button the small round airbag sticker previously removed in Step 5 dash disassembly. (Figure B) Continue to kit assembly.
PAGE 5
99-7424 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Single DIN Radio Housing and secure by bending the metal locking tabs outward. 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) Continue to final assembly.
PAGE 6
99-7424 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Snap the Trim plate onto the front of the Radio Housing. (Figure B) Continue to final assembly.
PAGE 7
99-7424 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation.
PAGE 8
99-7424 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV.