Car Stereo System User Manual

ManualsBrandsMetra Electronics ManualsAutomobile Accessories99-7506

INSTALLATION INSTRUCTIONS FOR PART 99-7506

Cutting Tool • Phillips Screwdriver • Socket Wrench

1-800-221-0932 www.metraonline.com

KIT FEATURES

• DIN Head Unit Provision with pocket

• ISO DIN Head Unit Provision with pocket

• Double DIN Head Unit Provision

• Stacked ISO DIN Head Unit Provision

• Painted Matte Black to Match Factory

A) Radio Housing • B) Snap-In Pocket • C) ISO Brackets • D) ISO Trim Plate • E) Double DIN Brackets

• F) Double DIN Trim Plate • G) (4) Panel Clips

KIT COMPONENTS

99-7506

APPLICATIONS

2006-2008

WIRING AND ANTENNA CONNECTIONS (Sold Separately)

Harness:

• 70-7903 - Mazda harness 2001-up

Antenna Adapter:

• Not required

Mazda MX-5 Miata

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7506 APPLICATIONS Mazda MX-5 Miata 2006-2008 99-7506 KIT FEATURES • DIN Head Unit Provision with pocket • ISO DIN Head Unit Provision with pocket • Double DIN Head Unit Provision • Stacked ISO DIN Head Unit Provision • Painted Matte Black to Match Factory KIT COMPONENTS A) Radio Housing • B) Snap-In Pocket • C) ISO Brackets • D) ISO Trim Plate • E) Double DIN Brackets • F) Double DIN Trim Plate • G) (4) Panel Clips B A F C D E F WIRING AND ANTENNA CONNECTIONS
PAGE 2
99-7506 TABLE OF CONTENTS Dash Disassembly ....................................................................... 1, 2 Kit Preparation ............................................................................... 3 Kit Assembly: DIN Head Unit Provision.................................................................. 4 ISO DIN Head Unit Provision........................................................... 5 Double DIN Head Unit Provision.....................................................
PAGE 3
99-7506 DASH DISASSEMBLY MAZDA MX-5 MIATA 2006-2008 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip panel below steering column and remove. (Figure A) 3 Remove (4) Phillips screws from metal brace below steering column and remove. (Figure A) 4 Looking at the side of the radio/climate control panel from underneath the steering column opening, remove (1) 10mm bolt from the side of the radio chassis.
PAGE 4
99-7506 DASH DISASSEMBLY MAZDA MX-5 MIATA 2006-2008 D 6 Remove (2) Phillips screws, (1) on each side, from the side of the radio/climate control panel. (Figure D) E 7 Pull radio/climate control panel out, disconnect plugs and remove. (Figure E) 8 Turn the radio/climate control panel over and remove the (4) screws that hold the climate control to the bezel, then remove the climate control.
PAGE 5
99-7506 KIT PREPARATION MAZDA MX-5 MIATA 2006-2008 A 1 Attach the (4) Panel Clips to the posts on the back of the radio housing.
PAGE 6
99-7506 KIT ASSEMBLY DIN HEAD UNIT PROVISION A 1 Turn over the 99-7506 housing, take the climate control and screws removed from the factory panel and attach the climate control to the kit housing using the factory screws. (Figure A) B 2 Slide the pocket into the bottom section of the kit housing. (Figure B) C 3 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure C) D 4 Slide the aftermarket head unit into the cage and secure.
PAGE 7
99-7506 KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION A 1 Turn over the 99-7506 housing, take the climate control and screws removed from the factory panel and attach the climate control to the kit housing using the factory screws. (Figure A) B 2 Slide the pocket into the bottom section of the kit housing. (Figure B) 3 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure C) 4 Slide the head unit into the radio opening until the side clips engage.
PAGE 8
99-7506 KIT ASSEMBLY DOUBLE DIN HEAD UNIT PROVISION A 1 Turn over the 99-7506 housing, take the climate control and screws removed from the factory panel and attach the climate control to the kit housing using the factory screws. (Figure A) 2 Cut the rib in the middle of the 997506 housing to make room for the DDIN brackets. (Figure A) B 3 Slide the appropriate DDIN bracket into the kit housing.
PAGE 9
9-7506 KIT ASSEMBLY STACKED ISO DIN HEAD UNIT PROVISION A 1 Turn over the 99-7506 housing, take the climate control and screws removed from the factory panel and attach the climate control to the kit housing using the factory screws. (Figure A) 2 Cut the rib in the middle of the 997506 housing to make room for the DDIN brackets. (Figure A) B 3 Slide the appropriate DDIN bracket into the kit housing.
PAGE 10
99-7506 FINAL ASSEMBLY FINAL ASSEMBLY 1 Locate the factory wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.
PAGE 11
99-7506 NOTES 9
PAGE 12
99-7506 INSTRUCTIONS 1-800-221-0932 REV. 09/16/10 www.metraonline.