Automobile Accessories User Manual

ManualsBrandsMetra Electronics ManualsAutomobile Accessories99-7519B

INSTALLATION INSTRUCTIONS FOR PART 99-7519B

Cutting Tool • Phillips Screwdriver • Socket Wrench

1-800-221-0932 www.metraonline.com

KIT FEATURES

• DIN Head Unit Provision with pocket

• ISO DIN Head Unit Provision with pocket

• Double DIN Head Unit Provision

• Stacked ISO DIN Head Unit Provision

• Painted Matte Black to Match Factory

A) Radio Housing • B) Snap-In Pocket • C) ISO Brackets • D) ISO Trim Plate • E) Double DIN Brackets

• F) Double DIN Trim Plate • G) (4) Panel Clips

KIT COMPONENTS

TOOLS REQUIRED:

99-7519B

APPLICATIONS

2009-2010

WIRING AND ANTENNA CONNECTIONS (Sold Separately)

Harness:

• 70-7903 - Mazda harness 2001-up

Antenna Adapter:

• Not required

Mazda MX-5 Miata

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7519B APPLICATIONS Mazda MX-5 Miata 2009-2010 99-7519B KIT FEATURES • DIN Head Unit Provision with pocket • ISO DIN Head Unit Provision with pocket • Double DIN Head Unit Provision • Stacked ISO DIN Head Unit Provision • Painted Matte Black to Match Factory KIT COMPONENTS A) Radio Housing • B) Snap-In Pocket • C) ISO Brackets • D) ISO Trim Plate • E) Double DIN Brackets • F) Double DIN Trim Plate • G) (4) Panel Clips B A F C D E F WIRING AND ANTENNA CONNECTION
PAGE 2
99-7519B TABLE OF CONTENTS Dash Disassembly ....................................................................... 1-3 Kit Preparation ............................................................................... 4 Kit Assembly: DIN Head Unit Provision.................................................................. 5 ISO DIN Head Unit Provision........................................................... 6 Double DIN Head Unit Provision.....................................................
PAGE 3
99-7519B DASH DISASSEMBLY MAZDA MX-5 MIATA 2009-2010 1 Unclip panel below steering column and remove. (Figure A) 2 Remove (4) Phillips screws from metal brace below steering column and remove. (Figure A) 3 Looking at the side of the radio/climate control panel from underneath the steering column opening, remove (1) 10mm bolt from the side of the radio chassis.
PAGE 4
99-7519B DASH DISASSEMBLY MAZDA MX-5 MIATA 2009-2010 6 E Unclip, unplug and remove the entire center console. (Figure E) F 7 Remove the (2) Phillips screws securing the side panels from each side of the radio/climate control panel. (Figure F) G 8 Carefully remove the side panels from each side of the radio/climate control panel by pulling straight back towards the rear of the car.
PAGE 5
99-7519B DASH DISASSEMBLY MAZDA MX-5 MIATA 2009-2010 H 9 Remove (2) Phillips screws, (1) on each side, from the side of the radio/climate control panel. (Figure H) I 10 Pull radio/climate control panel out, disconnect plugs and remove. (Figure I) J 11 Turn the radio/climate control panel over and remove the (4) screws that hold the climate control to the bezel, then remove the climate control.
PAGE 6
99-7519B KIT PREPARATION MAZDA MX-5 MIATA 2009-2010 A 1 Attach the (4) Panel Clips to the posts on the back of the radio housing.
PAGE 7
99-7519B KIT ASSEMBLY DIN HEAD UNIT PROVISION A 1 Turn over the 99-7519B housing, take the climate control and screws removed from the factory panel and attach the climate control to the kit housing using the factory screws. (Figure A) B 2 Slide the pocket into the bottom section of the kit housing. (Figure B) C 3 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure C) D 4 Slide the aftermarket head unit into the cage and secure.
PAGE 8
99-7519B KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION A 1 Turn over the 99-7519B housing, take the climate control and screws removed from the factory panel and attach the climate control to the kit housing using the factory screws. (Figure A) B 2 Slide the pocket into the bottom section of the kit housing. (Figure B) 3 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure C) 4 Slide the head unit into the radio opening until the side clips engage.
PAGE 9
9-7519B KIT ASSEMBLY DOUBLE DIN HEAD UNIT PROVISION 1 Turn over the 99-7519B housing, take the climate control and screws removed from the factory panel and attach the climate control to the kit housing using the factory screws. (Figure A) 2 Cut the rib in the middle of the 997519B housing to make room for the DDIN brackets. (Figure A) A B 3 Slide the appropriate DDIN bracket into the kit housing.
PAGE 10
99-7519B KIT ASSEMBLY STACKED ISO DIN HEAD UNIT PROVISION 1 Turn over the 99-7519B housing, take the climate control and screws removed from the factory panel and attach the climate control to the kit housing using the factory screws. (Figure A) 2 Cut the rib in the middle of the 997519B housing to make room for the DDIN brackets. (Figure A) A B 3 Slide the appropriate DDIN bracket into the kit housing.
PAGE 11
99-7519B FINAL ASSEMBLY FINAL ASSEMBLY 1 Locate the factory wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.
PAGE 12
99-7519B INSTRUCTIONS 1-800-221-0932 REV. 09/29/10 www.metraonline.