Car Stereo System - Car Radio User Manual

ManualsBrandsMetra Electronics ManualsCooktop99-7863

INSTALLATION INSTRUCTIONS FOR PART 99-7863

Phillips Screwdriver

1-800-221-0932 www.metraonline.com

KIT FEATURES

APPLICATIONS

Honda Element

2003-up

• DIN Head Unit Provision with pocket

• ISO Head Unit Provision with pocket

• A) Radio Housing • B) ISO Trimplate • C) ISO Snap in Brackets • D) O.E. Replacement Panel

KIT COMPONENTS

99-7863

TOOLS REQUIRED:

WIRING AND ANTENNA CONNECTIONS (Sold Separately)

Harness:

• 70-1721 - Honda/Acura harness 1998-up

• 70-7863

- Element sub and AUX integration

Antenna Adapter:

• 40-hd10 - Honad/Acura Antenna Adapter (for Element 2005-up)

BC D

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7863 APPLICATIONS Honda Element 2003-up 99-7863 KIT FEATURES • DIN Head Unit Provision with pocket • ISO Head Unit Provision with pocket KIT COMPONENTS • A) Radio Housing • B) ISO Trimplate • C) ISO Snap in Brackets • D) O.E.
PAGE 2
99-7863 TABLE OF CONTENTS Dash Disassembly - Honda Element 2003-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - DIN Head Unit Provision with Pocket . . . . . . . . . . . . . . . . . . . 2 - ISO Head Unit Provision with Pocket . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
99-7863 DASH DISASSEMBLY HONDA ELEMENT 2003-UP 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unsnap and remove shift lever trim panel. For manual transmission models, untwist shift knob. (Figure A) A R 1 B 3 Unsnap and remove center dash panel. (Figure B) C NOTE: As an option, the center panel (the smaller piece around radio) is all that needs to be removed, but it is very prone to damage, so full panel removal is recommended.
PAGE 4
99-7863 KIT ASSEMBLY DIN HEAD UNIT PROVISION WITH POCKET A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 2 Slide the aftermarket radio into the cage and secure. (Figure B) NOTE: Models equipped with factory DDIN radio will require supplied O.E. replacement panel. (Figure C) B Continue to final assembly.
PAGE 5
99-7863 KIT ASSEMBLY ISO HEAD UNIT PROVISION WITH POCKET 1 Align the holes in the ISO snap In brackets with the holes in the head unit and mount the brackets to the head unit with the screws supplied with the unit. (Figure A) 2 Slide the aftermarket head unit/bracket assembly into the radio opening until the side clips engage. (Figure B) 3 Snap the ISO trimplate over the head unit. (Figure B) A B NOTE: Models equipped with factory DDIN radio will require supplied O.E. replacement panel.
PAGE 6
99-7863 FINAL ASSEMBLY FINAL ASSEMBLY A B A) Strip wire ends back 1/2" B) Twist ends together C C) Solder D) Tape D 1 2 3 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. Reassemble in reverse order of disassembly.
PAGE 7
99-7863 NOTES 5
PAGE 8
99-7863 INSTRUCTIONS 1-800-221-0932 REV. 07/26/11 www.metraonline.