Automobile Accessories User Manual

ManualsBrandsMetra Electronics ManualsAutomobile Accessories99-7877S

INSTALLATION INSTRUCTIONS FOR PART 99-7877S

99-7877S

APPLICATIONS

Honda Fit 2009-10

KIT FEATURES

• DIN Radio Provision with Pocket

• ISO Mount Radio Provision with Pocket

• Double DIN Radio Provision

• Stacked ISO Mount Units Provision

• P

ainted To Match Factory Dash

“S”= SILVER

• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets

• E) Double DIN Trim Plate • F) Pocket

KIT COMPONENTS

Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver • Socket Set

1-800-221-0932

www.metraonline.com

WIRING AND ANTENNA CONNECTIONS

(Sold Separately)

• 70-1729 Honda Harness 2008-up

• 40-HD10 Honda Antenna Adapter 2005-up

TOOLS REQUIRED:

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7877S APPLICATIONS Honda Fit 2009-10 99-7877S KIT FEATURES • DIN Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • Double DIN Radio Provision • Stacked ISO Mount Units Provision • Painted To Match Factory Dash “S”= SILVER KIT COMPONENTS • A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate • F) Pocket C B A D WIRING AND ANTENNA CONNECTIONS (Sold Separately) • 70-1729 Honda Harness 2008-up
PAGE 2
99-7877S TABLE OF CONTENTS Dash Disassembly - Honda Fit 2009-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 - ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 4 - Double DIN Radio/ Stacked ISO Mount Units Provision . . . . . . . . . . . .
PAGE 3
99-7877S DASH DISASSEMBLY HONDA FIT 2009-10 1 Disconnect the negative battery terminal to prevent an accidental short circuit. A 2 Unclip and remove the lower center panel below radio. (Figure A) 3 Remove (1) 8 MM bolt facing up behind center panel. Note: Slide the recirculation control lever to FRESH for better access to bolt. (Figure A) 4 Open the upper glove box then use a pry tool to unclip and remove the radio/climate control assembly.
PAGE 4
99-7877S KIT PREPARATION KIT PREPARATION 1 Secure the hazard switch into the radio housing panel using the factory hardware. (Figure A) A 2 Secure the air bag light into the radio housing panel using the factory hardware. (Figure A) 3 Secure the a/c vents to the radio housing using the factory hardware. (Figure B) 4 Attach the (7) retaining clips to the radio housing panel in the same location as removed from the factory radio panel. B Continue to kit assembly.
PAGE 5
99-7877S KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. A 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 3 Slide the aftermarket head unit into the cage and secure.
PAGE 6
99-7877S KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. A 2 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure A) 3 Slide the head unit into the radio opening until the side clips engage.
PAGE 7
99-7877S KIT ASSEMBLY DOUBLE DIN RADIO PROVISION/ STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. A 2 Cut and remove the center bar from the radio housing. (Figure A) 3 Snap the Double DIN brackets to the inside edge of the Radio Housing.
PAGE 8
99-7877S INSTRUCTIONS 1-800-221-0932 REV. 4/22/10 www.metraonline.