Car Satellite Radio System User Manual

ManualsBrandsMetra Electronics ManualsCar Receiver99-8214TB

INSTALLATION INSTRUCTIONS FOR PART 99-8214

Phillips Screwdriver • Small Flat Blade Screwdriver • Socket Wrench

1-800-221-0932 www.metraonline.com

KIT FEATURES

• DIN Head Unit Provision With Pocket

• ISO DIN Head Unit Provision With Pocket

• Double DIN Head Unit Provision

• Stacked ISO DIN Head Unit Provision

• Painted And Textured To Match Factory Dash

• Available In Two Colors:

99-8214TB = BLACK, 99-8214TG = GRAY

• Both kits are factory “golf ball” style

textured.

• A) Radio Housing • B) Radio Housing Brackets

KIT COMPONENTS

APPLICATIONS

Toyota Tacoma 2005-2011

• C) Radio Housing Trim Panel • D) ISO Brackets

• E) ISO Trim Plate • F) (4) #6 x 3/8” Phillips Pan Head Screws

• G) (4) #8 X 3/8” Phillips Truss Head Screws • H) Double DIN Trim Plate • I) Clock/Hazard Switch Bracket

99-8214TB

99-8214TG

TOOLS REQUIRED:

WIRING AND ANTENNA CONNECTIONS (Sold Separately)

Harness:

• 70-1761 - Toyota harness 1987-up

• TYTO-01 - Toyota amp interface harness 2003-up

Antenna Adapter:

• Not required

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-8214 APPLICATIONS Toyota Tacoma 2005-2011 99-8214TB 99-8214TG KIT FEATURES • DIN Head Unit Provision With Pocket • ISO DIN Head Unit Provision With Pocket • Double DIN Head Unit Provision • Stacked ISO DIN Head Unit Provision • Painted And Textured To Match Factory Dash • Available In Two Colors: 99-8214TB = BLACK, 99-8214TG = GRAY • Both kits are factory “golf ball” style textured.
PAGE 2
99-8214 TABLE OF CONTENTS Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,4,5,6 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
99-8214 DASH DISASSEMBLY TOYOTA TACOMA 2005-2011 1 2 3 4 Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip and remove A/C control panel. (Figure A) A TEXT PWR VOL SCAN Remove (4) 10 MM bolts securing radio. (Figure B) Unclip and remove entire panel including hazard switch and clock. (Figure C) 5 Remove the left and right radio brackets from the radio chassis.
PAGE 4
99-8214 KIT PREPARATION TACOMA 2005-2011 (SKIP KIT PREPARATION WHEN INSTALLING DDIN RADIO) A 1 Attach the clock/hazard switch bracket to the radio housing using the (4) #6 x 3/8” Phillips pan head screws. WARNING: DO NOT OVERTIGHTEN SCREWS. 2 Clip the clock/hazard switch assembly into the 99-8214 Radio Housing Trim Panel. (Figure A,B) Continue to Kit Assembly.
PAGE 5
99-8214 KIT ASSEMBLY TOYOTA TACOMA 2005-2011 DIN HEAD UNIT PROVISION A 1 Attach the corresponding radio housing bracket to the radio housing using the included (4) #8 x 3/8” 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure B) 3 Slide the aftermarket head unit into the cage and secure. (Figure C) 4 Secure the Radio Housing into the dash using the factory hardware. B Continue to Final Assembly.
PAGE 6
99-8214 KIT ASSEMBLY TOYOTA TACOMA 2005-2011 ISO DIN HEAD UNIT PROVISION A 1 Attach the corresponding radio housing bracket to the radio housing using the included (4) #8 x 3/8” Phillips truss head screws.(Figure A) 2 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure B) 3 Slide the head unit into the radio opening until the side clips engage. (Figure C) 4 Snap the ISO Trim Plate into the Radio Housing.
PAGE 7
99-8214 KIT ASSEMBLY DOUBLE DIN HEAD UNIT PROVISION A 1 Slide the aftermarket radio unit into the factory brackets and secure the unit to the brackets using the screws supplied with the head unit. (Figure A) 2 Secure the aftermarket radio unit and factory bracket assembly into the sub dash. (Figure B) 3 Place the Double DIN trim plate into the back of the radio housing, then attach the clock/hazard switch bracket assembly using the (4) #6 x 3/8” Phillips pan head screws.
PAGE 8
99-8214 KIT ASSEMBLY STACKED ISO DIN HEAD UNIT PROVISION A 1 Slide the aftermarket radio units into the factory brackets and secure the unit to the brackets using the screws supplied with the head unit. (Figure A) 2 Secure the aftermarket radio units and factory bracket assembly into the sub dash. (Figure B) 3 Remove the (4) screws securing the clock/hazard switch bracket to the radio housing and remove the clock/hazard switch bracket assembly.
PAGE 9
9-8214 FINAL ASSEMBLY FINAL ASSEMBLY 1 Locate the factory wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.
PAGE 10
99-8214 NOTES 8
PAGE 11
99-8214 NOTES 9
PAGE 12
99-8214 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV.