Radio - HD Radio User Manual

ManualsBrandsMetra Electronics ManualsVentilation HoodACURA 95-7868B

INSTALLATION INSTRUCTIONS FOR PART 95-7868B

95-7868B

APPLICATIONS

ACURA

CL 2001-2003

TL 1999-2003

KIT FEATURES

• Double DIN Radio Provision

• Stacked ISO Mount Units Provision

• A) Double DIN Radio Housing • B) Double DIN Brackets • C) Double DIN Trim Plate

• D) (2) Phillips Screws

KIT COMPONENTS

TOOLS REQUIRED:

• Phillips Screwdriver • Socket Set

1-800-221-0932

TION

www.metr

aonline.com

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 95-7868B APPLICATIONS ACURA CL 2001-2003 TL 1999-2003 95-7868B KIT FEATURES • Double DIN Radio Provision • Stacked ISO Mount Units Provision KIT COMPONENTS • A) Double DIN Radio Housing • B) Double DIN Brackets • C) Double DIN Trim Plate • D) (2) Phillips Screws D B A C TOOLS REQUIRED: • Phillips Screwdriver • Socket Set 1-800-221-0932 www.metraonline.
PAGE 2
95-7868B TABLE OF CONTENTS Dash Disassembly - ACURA CL 2001-2003/TL 1999-2003 . . . . . . . . . . . . . . . . . . 1,2 Kit Assembly - Double DIN Radio Provision/ Stacked ISO Mount Units Provision . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 *Note: Refer also to the instructions included with the aftermarket radio.
PAGE 3
95-7868B DASH DISASSEMBLY ACURA CL 2001-2003 / TL 1999-2003 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove wood trim from both sides of center console. (Figure A) 3 Open armrest and remove (2) Phillips screws inside and (2) Phillips at front edge of rear of console and pull rearward. (Figure B) 4 Open fuse access and remove (1) Phillips screw then unclip and remove panel below steering column.
PAGE 4
95-7868B DASH DISASSEMBLY ACURA CL 2001-2003 / TL 1999-2003 E 6 Unclip and remove seat heater switch trim panel to access (2) Phillips screws and remove screws. (Figure E) 7 Unclip bottom of A/C control trim panel and pull away (no need to completely remove). (Figure F) 8 Remove (3) Phillips screws and (1) push pin per side of radio to remove radio. (Figure G) 9 Remove (2) Phillips screws from storage pocket assembly above radio to separate.
PAGE 5
95-7868B KIT ASSEMBLY DOUBLE DIN RADIO PROVISION/ STACKED ISO MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. 1 Snap the Double DIN brackets to the inside edge of the Double DIN radio housing. (Figure A) A 2 Slide the Double DIN head unit or stacked ISO head units into the bracket/radio housing assembly and secure the Double DIN head unit or stacked ISO head units to the assembly using the screws supplied with the radio.
PAGE 6
95-7868B FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation.
PAGE 7
95-7868B NOTES 5
PAGE 8
95-7868B INSTRUCTIONS 1-800-221-0932 REV. 03/02/09 www.metraonline.