Car Stereo System - Car Radio Tuner User Manual

ManualsBrandsMetra Electronics ManualsSpeakerMAZDA CX7 2007-09 99-7508

INSTALLATION INSTRUCTIONS FOR PART 99-7508

99-7508

APPLICATIONS

Mazda CX7 2007-09

KIT FEATURES

• DIN Radio Provision with Pocket

• ISO Mount Radio Provision with Pocket

• Double DIN Mount Radio Provision

• Stacked ISO Mount Units Provision

• Painted Matte Black to Match Factory

• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets

• E) Double DIN Trim Plate • F) Pocket

Wiring & Antenna Connections (sold separately)

• 70-7903T - Mazda Service Harness 07-up

KIT COMPONENTS

TOOLS REQUIRED:

Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver

1-800-221-0932

www.metraonline.com

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7508 APPLICATIONS Mazda CX7 2007-09 99-7508 KIT FEATURES • DIN Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • Double DIN Mount Radio Provision • Stacked ISO Mount Units Provision • Painted Matte Black to Match Factory KIT COMPONENTS • A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate • F) Pocket Wiring & Antenna Connections (sold separately) • 70-7903T - Mazda Service Harness 07-up C B
PAGE 2
99-7508 TABLE OF CONTENTS Dash Disassembly - Mazda CX7 2007 -2009. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 4 - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
99-7508 DASH DISASSEMBLY MAZDA CX7 2007-2009 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the trim panel surrounding the radio and climate controls. (Figure A) 3 Remove (4) Phillips screws securing the radio. Unplug and remove radio. (Figure B) 2 3 4 4 Remove (2) Phillips screws securing the hazard switch to the factory radio then separate the front half from the rear half of the switch to remove.
PAGE 4
99-7508 KIT PREPARATION MAZDA CX7 2007-2009 1 Secure the hazard switch into the 99-7508 radio housing using the factory hardware.
PAGE 5
99-7508 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the DIN cage until it snaps into place. (Figure B) 3 Snap the pocket into the radio housing. (Figure C) Continue to final assembly.
PAGE 6
99-7508 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Snap the Trim Plate onto the front of the Radio Housing. (Figure B) 4 Snap the Pocket into the Radio Housing. (Figure C) B Continue to final assembly.
PAGE 7
99-7508 KIT ASSEMBLY DOUBLE DIN OR STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the Radio Housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the Radio Housing. (Figure B) 3 Slide the Double DIN or stacked ISO mount units into the bracket/radio housing assembly then secure it to the assembly using the screws supplied with the Double DIN or ISO mount units.
PAGE 8
99-7508 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation.
PAGE 9
9-7508 NOTES 7
PAGE 10
99-7508 NOTES 8
PAGE 11
99-7508 NOTES 9
PAGE 12
99-7508 INSTRUCTIONS 1-800-221-0932 www.metraonline.com Rev.