Installation Instructions

ManualsBrandsMetra ManualsAudioMetra Mini Countryman/Paceman 2011-2016 (Without Factory NAV) Dash Kit

Metra. The World’s Best Kits.



INSTALLATION INSTRUCTIONS

107-MI1

Patent Pending

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

KIT FEATURES

• Designed speciﬁcally for Pioneer modular 6.8” radios like the

DMH-C2550NEX and DMH-C2500NEX.

(Refer to the radio manufacturer for current models)

• Blank-out included for factory radio controls removed from upper panel

KIT COMPONENTS

• A) Assembly mount • B) Radio chassis brackets • C) Display brackets • D) Display housing • E) Display Trim ring • F) Block out panel

• G) 4mm Allen head Screws (4)

TOOLS REQUIRED

• 10mm socket set • Lots of different Torx

• Allen head driver • Cutting tool

• Panel removal tool • Phillips screwdriver

TABLE OF CONTENTS

Dash Disassembly ..............................................2-6

Kit Preparation .......................................................6

Kit Assembly ..........................................................7

WIRING & ANTENNA CONNECTIONS

(sold separately)

Wiring Harness: LC-BMRC-01

Antenna Adapter: 40-EU10

A CB

D E F

Mini Countryman & Paceman 2011-2016

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle

speciﬁc applications

(without factory NAV)

Summary of content (8 pages)

PAGE 1
07-MI1 I N S TA L L AT I O N I N S T R U C T I O N S Patent Pending Mini Countryman & Paceman 2011-2016 (without factory NAV) Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications KIT FEATURES • Designed specifically for Pioneer modular 6.8” radios like the DMH-C2550NEX and DMH-C2500NEX.
PAGE 2
DASH DISASSEMBLY 1. Unclip and remove the trim panel to the right of the glove box above the kick panel. (Figure A) 2. Unclip and remove the passenger side kick panel. (Figure B) 3. Remove (2) Torx screws (facing up) from the panel below the glove box then unclip the front edge of the panel and let hang. (Figure C) Continued on the next page 2 (Figure A) (Figure B) (Figure C) 1.800.221.0932 | MetraOnline.
PAGE 3
DASH DISASSEMBLY 4. Remove (7) Torx screws (2 on bottom, 3 on top edge with door open, and 2 from right side) securing the glove box then unclip and remove the glove box assembly. (Figures D, E) (CONT.) 5. Unclip and remove the panel to the left of the driver’s side knee bolster panel. (Figure F) 6. Remove (3) Torx screws securing the knee bolster panel then unclip and remove the panel. (Figure G) Continued on the next page (Figure D) (Figure F) (Figure E) (Figure G) REV.
PAGE 4
DASH DISASSEMBLY 7. Pull the rubber cover in the center console back to reveal (1) Torx screw on shifter trim panel. (Figure H) 9. Remove (1) Torx screw from the trim panel in front of the shifter trim panel then unclip and remove the panel. (Figure J) 8. Remove (2) Torx screws from inside the cup holders and the (1) Torx screw exposed in step 7 then unclip and slide the shifter trim panel rearward (toward rear of vehicle). (Figure I) 4 (CONT.) 10.
PAGE 5
DASH DISASSEMBLY 11. Unclip and remove the trim panel surrounding the speedometer and a/c vents. (Figure L) (CONT.) 13. Remove (7) Torx screws securing the sub trim panel surrounding the speedometer and a/c vents then unclip and remove the panel. (Figure N) 12. Remove (10) Torx screws from the center stack surrounding the a/c controls and window switches then unclip disconnect and remove the center stack. (Figure M) 14.
PAGE 6
DASH DISASSEMBLY (CONT.) 15. Push the two clips in on the back of the speedometer and lift up carefully to separate the chassis and speedometer, then unplug the ribbon cable and set speedometer aside for reassembly. (Figures P,Q) KIT PREPARATION 16. Remove (4) Torx screws securing the radio controls, then remove the entire assembly from the speedometer. (Figure A) 17. Secure the block out panel to the speedometer using (2) of the factory screws.
PAGE 7
KIT ASSEMBLY Note: For steps 2 and 5, reference the installation manual provided with the radio for which hardware to use. The display screen and radio chassis use two different types of screws. 1. Secure the display brackets to the assembly mount using (4) Allen head screws provided. (Figure A) 4. Route the RGB display cable from the radio chassis, through the opening in the assembly mount. 5. Secure the radio display to the display housing using (4) screws supplied with the radio.
PAGE 8
107-MI1 I N S TA L L AT I O N I N S T R U C T I O N S Having difficulties? We’re here to help. Contact our Tech Support line at: 386-257-1187 Or via email at: techsupport@metra-autosound.com Tech Support Hours (Eastern Standard Time) Monday - Friday: 9:00 AM - 7:00 PM Saturday: 10:00 AM - 7:00 PM Sunday: 10:00 AM - 4:00 PM ® KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.