Owner's Manual

ManualsBrandsMetra ManualsAudio accessories & installation108-TO3BR

Metra. The World’s Best Kits.



INSTALLATION INSTRUCTIONS

108-TO3

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

Patent Pending

KIT FEATURES

• Designed speciﬁcally for the Pioneer DMH-C5500NEX 8-inch radio

• 108-TO3B = Black, 108-TO3BR = Brown

KIT COMPONENTS

• A) Radio trim panel • B) Radio brackets • C) Panel clips (4)

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• Cutting tool • 10mm socket wrench

TABLE OF CONTENTS

Dash Disassembly ..................................................2

Kit Preparation ...................................................3-4

Kit Assembly ..........................................................5

WIRING & ANTENNA CONNECTIONS

(sold separately)

Wiring Harness: 70-1761 • TYTO-01 (w/ amp)

Antenna Adapter: Not required

A B C

Toyota Highlander (w/o NAV) 2008-2012

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle

speciﬁc applications

Summary of content (9 pages)

PAGE 1
08-TO3 I N S TA L L AT I O N I N S T R U C T I O N S Patent Pending Toyota Highlander (w/o NAV) 2008-2012 Visit MetraOnline.
PAGE 2
DASH DISASSEMBLY 1. Unclip and remove the a/c vent panel. (Figure A) 2. Unclip, unplug, and remove the climate control panel. (Figure B) 3. Remove (4) 10mm bolts securing the radio. Slide the radio out, then unplug and remove the radio/display assembly. (Figure C) Continue to Kit Preparation (Figure A) 2 (Figure B) (Figure C) 1.800.221.0932 | MetraOnline.
PAGE 3
KIT PREPARATION From the factory radio/display assembly: 1. Remove (2) Phillips screws securing the display panel, then remove. (Figure A) One screw on each side 2. Unclip and remove the hazard switch assembly. (Figure B) 3. Remove (4) panel clips. (Figure C) Continued on the next page (Figure A) (Figure C (Figure B) REV.
PAGE 4
KIT PREPARATION (CONT.) To the 108-TO3 radio housing: 5. Secure the radio brackets to the factory display panel using the factory screws. (Figure D) 6. Clip in the hazard switch assembly. (Figure E) 7. Attach the (4) factory panel clips removed in step 3. (Figure E) Note: Panel clips have been provided in case the factory clips are missing or are damaged. Continue to Kit Assembly (Figure D) 4 (Figure E) 1.800.221.0932 | MetraOnline.
PAGE 5
KIT ASSEMBLY Note: For steps 1 and 2, reference the installation manual provided with the radio for which hardware to use. The display screen and radio chassis use two different types of screws. 1. Slide the radio chassis between the radio brackets, then secure using (4) screws supplied with the radio. (Figure A) 2. Secure the radio display to the radio brackets using (4) screws supplied with the radio. (Figure B) 3.
PAGE 6
1.800.221.0932 | MetraOnline.
PAGE 7
REV.
PAGE 8
108-TO3 I N S TA L L AT I O N I N S T R U C T I O N S If you are having difficulties with the installation of this product, contact our Tech Support line either by phone at 386-257-1187, or email at techsupport@metra-autosound.com. Before doing so, look over the instruction booklet a second time and ensure that the installation was performed exactly as the instruction booklet is stated. Have the vehicle apart and ready to perform troubleshooting steps before contacting Metra/Axxess Tech Support.
PAGE 9
108-TO3 Toyota Highlander 2008-2012 Without NAV Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications. D Designed specifically for the Pioneer DMH-C5500NEX 8-inch radio P 108-TO3B = Black P 108-TO3BR = Brown KIT COMPONENTS • Radio trim panel • Radio brackets • Panel clips (4) WIRING & ANTENNA CONNECTIONS (sold separately) • Wiring Harness: 70-1761 • TYTO-01 (w/ amp) • Antenna Adapter: Not required HARDWARE INCLUDED SALES 386-257-2956 Metra.