Installation instructions

ManualsBrandsMetra ManualsMobile Phones82-9600

APPLICATIONS

METRA. The World’s best kits.

™

metraonline.com1-800-221-0932

REV. 4/14/2014 INST82-9600

CAUTION: Metra recommends disconnecting the

negative battery terminal before beginning any

installation. All accessories, switches, and especially

air bag indicator lights must be plugged in before

reconnecting the battery or cycling the ignition.

NOTE: Refer to the instructions included with the

aftermarket radio.

Table of Contents

INSTALLATION INSTRUCTIONS FOR PART 82-9600

• Mounts aftermarket 6” to 6.5” speakers into

factory speaker locations.

• A) (2) speaker adapters • B) (6) #8 x 1” Pan-head Phillips screws

KIT FEATURES

KIT COMPONENTS

• Panel removal tool • Phillips screwdriver • Socket Wrench (T-25, T-27, 6mm or 3/16 hex)

TOOLS REQUIRED

Harley-Davidson 1998-2013

(FL models with fairings)

82-9600

A B

Fairing Disassembly

– Harley-Davidson FLH, batwing fairing

... 1998-2013 .......................................................2-3

– Harley-Davidson Roadglide, sharknose fairing

... 1998-2013 .......................................................4-5

Kit Assembly .......................................................... 6

Summary of content (16 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 82-9600 APPLICATIONS Table of Contents Harley-Davidson 1998-2013 Fairing Disassembly (FL models with fairings) – Harley-Davidson FLH, batwing fairing ... 1998-2013 .......................................................2-3 82-9600 – Harley-Davidson Roadglide, sharknose fairing ... 1998-2013 .......................................................4-5 KIT FEATURES • Mounts aftermarket 6” to 6.5” speakers into factory speaker locations. Kit Assembly ..................
PAGE 2
82-9600 Fairing Disassembly FLH/Batwing models: 1. Cover the front fender. 2. Remove (2) T-27 Torx bolts from inner fairing (under mirrors) (Figure A, step 2) Step 4 3. Remove (2) T-27 Torx bolts from outer edges of inner fairing near the fork tubes (facing forward) (Figure A, step 3) 4. Remove (3) T-27 Torx bolts from bottom edge of windshield. (Figure A, step 4) NOTE: Windshield and fairing will be loose once these screws are removed. Use extreme caution not to damage fairing or windshield. 5.
PAGE 3
82-9600 Fairing Disassembly FLH/Batwing models: (cont.) 6. Lift away and unplug headlight to remove outer fairing. (Figure B) 7. Unbolt and remove inner fairing support brackets from each side (3/16” Allen & T-25 Torx screws). Note the Torx screw is also a shared speaker screw. (Figure C) 8. Remove the remaining speaker screws and the speaker.
PAGE 4
82-9600 Fairing Disassembly Roadglide/Sharknose models 1. Loosen (6) T-25 Torx bolts from bottom, middle and top of left and right sides of the inner fairing.
PAGE 5
82-9600 Fairing Disassembly Roadglide/Sharknose models (cont.) 2. Use a 1/2” socket or box wrench to remove the (2) acorn nuts that hold each turn signal at the lower fairing. Let the signals hang loose. (Figure B) 3. Lift away the fairing, unplug the headlights and remove. 4. Remove the speaker screws and the speaker.
PAGE 6
82-9600 Kit Assembly 1. Using 3 of the screws in the provided hardware, mount the speaker adapter to the inner fairing. The 4th inner bottom screw locations are not used on FLH/ batwing models. For Road Glide models, rotate the adapter until the notches in the adapter do not hit the factory mounting posts and the flat spots on the outside of the adapter are toward the outer edge of the fairing. (Figure A) 2. Mount the new speaker with the hardware provided with the speakers.
PAGE 7
82-9600
PAGE 8
INSTALLATION INSTRUCTIONS FOR PART 99-9600 KNOWLEDGE IS POWER REV. 4/14/2014 INST82-9600 Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians METRA. The World’s best kits.™ 1-800-221-0932 metraonline.
PAGE 9
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 82-9600 AplicAciones Indice Harley-Davidson 1998-2013 Desensamble del carenado (Modelos FL con carenados) 82-9600 – Harley-Davidson Modelos FLH/alas de murciélago ... 1998-2013 .......................................................2-3 – Harley-Davidson Modelos Roadglide/Sharknose ... 1998-2013 .......................................................4-5 cArActerísticAs del kit • Monta bocinas de 6” a 6.
PAGE 10
82-9600 Desensamble del carenado Modelos FLH/alas de murciélago 1. Cubierta de la salpicadera delantera 2. Retire (2) pernos T-27 Torx del carenado interior (abajo de los espejos). (Figura A, paso 2) Paso 4 3. Retire (2) pernos T-27 Torx de los bordes del carenado interior cerca de los tubos de horquilla (orientado hacia el frente) (Figura A, paso 3) 4. Retire (3) pernos T-27 Torx del borde inferior del parabrisas.
PAGE 11
82-9600 Desensamble del carenado Modelos FLH/alas de murciélago (cont.) 6. Levante y desconecte el faro delantero para retirar el carenado exterior. (Figura B) 7. Desatornille el perno y retire los soportes de apoyo del carenado interior en cada lado (tornillos Allen 3/16” y T-25 Torx). Tenga en cuenta de que el tornillo Torx también es un tornillo que se comparte con las bocinas. (Figura C) (Figura B) (Figura C) 8. Retire los tornillos restantes de la bocina y la bocina.
PAGE 12
82-9600 Desensamble del carenado Modelos Roadglide/Sharknose 1. Afloje (6) pernos T-25 Torx de la parte inferior, media y superior del lado derecho e izquierdo del carenado interior.
PAGE 13
82-9600 Desensamble del carenado Modelos Roadglide/Sharknose (cont.) 2. Use una llave de cubo de 1/2” para retirar las (2) tuercas ciegas que sostienen cada señal direccional en el carenado inferior. Deje colgando las señales direccionales. (Figura B) 3. Levante el carenado, desconecte los faros delanteros y retírelos. 4. Retire los tornillos de la bocina y la bocina.
PAGE 14
82-9600 Ensamble del kit 1. Use 3 de los tornillos que vienen en la tornillería, monte el adaptador de bocina en el carenado interior. Los lugares del 4o tornillo inferior interior no se usan en los modelos FLH/ala de murciélago. Para los modelos Road Glide, gire el adaptador hasta que las muescas en él no golpeen con los postes de montaje de fábrica y las partes planas externas del adaptador estén orientadas hacia el borde exterior del carenado. (Figura A) 2.
PAGE 15
82-9600 7
PAGE 16
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 82-9600 EL CONOCIMIENTO ESOWER PODER K NOWLEDGE IS P Mejore sus habilidades de instalación y fabricación REV. 4/14/2014 INST82-9600 Enhance your installation and fabrication skills by enrolling in the en most recognized and respected inscribiéndose la escuela de dispositivos electrónicos mobile school in our industry. móvileselectronics más reconocida y respetada de nuestra industria. Log onto www.installerinstitute.com or call Regístrese en www.