Datasheet

ManualsBrandsMetra Manualschassis components95-7425

INSTALLATION INSTRUCTIONS FOR PART 95-7425

95-7425

APPLICATIONS

Nissan Rogue 2008-11

KIT FEATURES

• Double DIN Radio Provision

• Stacked ISO Mount Units Provision

A) Double DIN Radio Housing • B) Double DIN Brackets

Harness & Antenna Connections (sold separately)

• 70-7552 - Nissan Harness 07-up

• 40-NI12 - Nissan Antenna Adapter 07-up

KIT COMPONENTS

TOOLS REQUIRED:

Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver

1-800-221-0932

www.metraonline.com

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 95-7425 APPLICATIONS Nissan Rogue 2008-11 95-7425 KIT FEATURES • Double DIN Radio Provision • Stacked ISO Mount Units Provision KIT COMPONENTS A) Double DIN Radio Housing • B) Double DIN Brackets A B Harness & Antenna Connections (sold separately) • 70-7552 - Nissan Harness 07-up • 40-NI12 - Nissan Antenna Adapter 07-up TOOLS REQUIRED: Small Flat Blade Screwdriver/ Panel Removal Tool • Phillips Screwdriver 1-800-221-0932 www.metraonline.
PAGE 2
95-7425 TABLE OF CONTENTS Dash Disassembly - Nissan Rogue 2008-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1,2 Kit Assembly - Double DIN/ Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 *Note: Refer also to the instructions included with the aftermarket radio.
PAGE 3
95-7425 DASH DISASSEMBLY NISSAN Rogue 2008-11 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 If equipped with center speaker: Unclip and remove the grille (Figure A). Remove (4) Phillips screws securing the speaker. Unplug and remove the speaker. (Figure B). Unclip the panel above the radio including the a/c vents, then unplug hazard switch and remove. (Figure C) B Note: If not equipped with center speaker skip step number 2. Continued on page 2.
PAGE 4
95-7425 DASH DISASSEMBLY NISSAN Rogue 2008-11 D 3 Unclip the panel below the radio including the climate controls. Unplug climate controls and remove the panel. (Figure D) 4 Remove (4) Phillips screws securing the radio, unplug and remove radio. (Figure E) Continue to kit assembly.
PAGE 5
95-7425 KIT ASSEMBLY DOUBLE DIN/STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the Double DIN brackets to the inside edge of the Double DIN radio housing. (Figure A) 2 Slide the Double DIN or the stacked ISO mount unit(s) into the bracket/radio housing assembly and secure the unit(s) to the assembly using the screws supplied with the unit(s). (Figure B) Continue to final assembly.
PAGE 6
95-7425 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble in reverse order of disassembly.
PAGE 7
95-7425 NOTES 5
PAGE 8
95-7425 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV.