User Manual

ManualsBrandsMetra ManualsAutomotiveMetra 95-7899 Double DIN Installation Kit for 2001-2005 Honda Civic Vehicles Excluding SE

INSTALLATION INSTRUCTIONS FOR PART 95-7899

Phillips Screwdriver • Utility Knife • Socket Wrench

1-800-221-0932 www.metraonline.com

KIT FEATURES

APPLICATIONS

2001-2005 Honda Civic

(Except 2005 Civic SE)

• Double DIN Head Unit Provision

• Stacked ISO DIN Head Unit Provision

• A) Double DIN Trim Plate

KIT COMPONENTS

TOOLS REQUIRED:

95-7899

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 95-7899 APPLICATIONS 2001-2005 Honda Civic (Except 2005 Civic SE) 95-7899 KIT FEATURES • Double DIN Head Unit Provision • Stacked ISO DIN Head Unit Provision KIT COMPONENTS • A) Double DIN Trim Plate A TOOLS REQUIRED: Phillips Screwdriver • Utility Knife • Socket Wrench 1-800-221-0932 www.metraonline.
PAGE 2
95-7899 TABLE OF CONTENTS Dash Disassembly - 2001-2005 Honda Civic (Except 2005 Civic SE) Center Console Without Armrest . . . . . . . . . . . . . . . . . . . . . . . . 1 Center Console With Armrest . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Kit Assembly - Double DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . 3 - Stacked ISO Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
95-7899 2001-2005 HONDA CIVIC DASH DISASSEMBLY (EXCEPT 2005 CIVIC SE) CENTER CONSOLE WITHOUT ARMREST 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip the parking brake trim panel and remove (2) Phillips screws exposed. (Figure A) 3 Remove (1) Phillips screw and (1) clip from each side of the center console. (Figure B) Slide the console rearward to access (2) Phillips screws on the power outlet panel.
PAGE 4
95-7899 2001-2005 HONDA CIVIC DASH DISASSEMBLY (EXCEPT 2005 CIVIC SE) CENTER CONSOLE WITH ARMREST 1 2 3 Disconnect the negative battery terminal to prevent an accidental short circuit. Automatic transmission: a. Apply parking brake and place shifter in neutral position. b. Unclip and remove trimring around shifter. (Figure A) Manual transmission: a. Apply parking brake b.
PAGE 5
95-7899 KIT ASSEMBLY DOUBLE DIN HEAD UNIT PROVISION 1 Remove the center bar from DDIN Trimplate. (Figure A) 2 Snap the DDIN Trimplate into the bracket and unit assembly. (Figure B) A 3 Attach the aftermarket radio to the factory brackets by aligning the holes and securing it to the brackets using the screws supplied with radio. (Figure C) B 4 Skip to step #1 in the Final Assembly.
PAGE 6
95-7899 KIT ASSEMBLY STACKED ISO HEAD UNIT PROVISION 1 Depending on the type of aftermarket head units being installed (ie: Flip down, removable and motorized faced head units) the center bar may have to be removed and a small portion of the inside top and bottom edge of the DDIN Trimplate may have to be filed slightly. (Figure A) 2 Snap the DDIN Trimplate to the bracket & unit assembly.
PAGE 7
95-7899 FINAL ASSEMBLY FINAL ASSEMBLY A B C A) Strip wire ends back 1/2" B) Twist ends together C) Solder D) Tape D 1 Locate the factory wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation.
PAGE 8
95-7899 INSTRUCTIONS 1-800-221-0932 REV. 04/15/08 www.metraonline.