Owner's Manual

ManualsBrandsMetra ManualsAutomotiveMetra 95-8202 Toyota DDIN Multi Dash Kit

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

The World’s best kits.



INSTALLATION INSTRUCTIONS

95-8202

KIT FEATURES

• ISO DDIN radio provision

KIT COMPONENTS

• A) ISO DDIN trim plate brackets

TOOLS REQUIRED

• Cutting tool • Phillips screwdriver • Socket set

• Dremel/grinder tool

TABLE OF CONTENTS

See Page 2

WIRING & ANTENNA CONNECTIONS

(sold separately)

Wiring Harness: Please visit metraonline.com

for wiring harness options

Antenna Adapter: Please visit metraonline.com

for antenna adapter options

Toyota/Scion Multi-kit 2000-2017

APPLICATIONS

See inside front cover

Summary of content (40 pages)

PAGE 1
95-8202 I N S TA L L AT I O N I N S T R U C T I O N S Toyota/Scion Multi-kit 2000-2017 TABLE OF CONTENTS See Page 2 KIT FEATURES • ISO DDIN radio provision WIRING & ANTENNA CONNECTIONS (sold separately) Wiring Harness: Please visit metraonline.com for wiring harness options Antenna Adapter: Please visit metraonline.
PAGE 2
APPLICATIONS Toyota Rav-4 MR2 Spyder Celica Echo Highlander (without factory navigation) Matrix Matrix (with factory navigation) 4 Runner (excluding limited) Tundra Sequoia FJ Cruiser Yaris (without power package) Yaris TABLE OF CONTENTS 2001-2005 2000-2005 2000-2005 2000-2005 2001-2007 2005-2008 2009-2010 2003-2009 2003-2006 2003-2007 2007-2014 2007-2011 2012-2017 2013-2016 2012-2015 2005-2016 2004-2006 2004-2015 2008-2014 Subaru BRZ Forester (with SD based navigation) 2013-2015 2009-2013 – Scion xB 2
PAGE 3
DASH DISASSEMBLY Toyota Rav-4 2001-2005 Toyota MR2 Spyder 2000-2005 1. Unclip and remove side panel from both sides of radio and climate controls. (Figure A) 1. Unsnap the lower trim piece from each side of the dash console and remove (2) Phillips screws exposed in each cavity. Remove the upper trim piece from each side of the console. (Figure A) 2. Remove (4) Phillips screws securing the radio/climate control trim panel. (Figure B) 3. Remove (4) 10mm bolts securing the radio. (Figure C) 4.
PAGE 4
DASH DISASSEMBLY Toyota Celica 2000-2005 1. Unclip and remove the gear shifter trim bezel and remove (2) Phillips screws exposed below the climate controls. (Figure A) 2. Pull off climate control knobs and remove (2) Phillips screws exposed. (Figure A) 3. Unclip the climate control/factory radio trim bezel and remove. (Figure A) (Figure A) 4 4. Remove (4) 10mm screws securing the factory radio and disconnect the wiring. 5. Remove factory brackets from radio. Retain brackets for use during kit assembly.
PAGE 5
DASH DISASSEMBLY Toyota Highlander 2001-2007 (without factory navigation) 1. Pull and remove dash panel from radio and climate controls. Tip: There are 8 clips. (Figure A) 2. Remove (6) 10mm bolts from radio and climate controls assembly. (Figure B) Toyota Matrix 2005-2008 1. Unclip the bottom edge of the radio trim panel then lift up and out to remove. (Figure A) 2. Remove (4) 10mm bolts securing the factory radio. (Figure B) (Figure A) 3. Remove assembly and disconnect the wiring. 4.
PAGE 6
DASH DISASSEMBLY Toyota Matrix 2009-2010 (with factory navigation) (CONT) Toyota 4-Runner 2003-2009 (excluding limited) 1. Unclip and remove the radio trim panel including the A/C vent. (Figure A) 1. Unsnap and remove trim from around shifter. PASSENGER SECURITY 2. Remove (4) 10mm bolts securing the factory radio. Unplug and remove the radio. (Figure B) 2. Unsnap and remove trim covers from around center console pocket edge at front and rear of console. 3. Unsnap and remove center console cover.
PAGE 7
DASH DISASSEMBLY Toyota 4-Runner 2003-2009 (Cont) (excluding limited) Toyota Tundra 2003-2006 1. Remove the (3) climate control knobs by pulling straight outward. (Figure A) 7. Remove (1) 10mm bolt beneath climate control behind pocket door. Unsnap and remove climate control. (Figure C) 2. Remove (3) Phillips screws from behind knobs. (Figure A) 8. Remove (2) 10mm bolts beneath radio behind climate controls. 9. Unsnap and remove entire center panel around radio. (Figure D) (CONT) (Figure B) 10.
PAGE 8
DASH DISASSEMBLY (CONT) Toyota Tundra 2003-2006 (Cont) Toyota Sequoia 2003-2007 4. Unclip and remove entire trim panel. (Figure C) 1. Position vents facing upward and remove (1) Phillips screw from each A/C vent. (Figure A) 5. Remove (4) 10mm bolts to remove radio. (Figure D) 2. Unclip and remove entire radio trim panel including climate controls. (Figure B) 6. Unplug and remove radio. 3. Remove (4) 10mm bolts to remove radio. (Figure C) 7. Remove factory brackets from radio.
PAGE 9
DASH DISASSEMBLY (CONT) Toyota FJ Cruiser 2007-2014 1. Remove two Phillips screws from bottom part of side trim panels. (Figure A) 2. Using a panel removal tool, carefully remove the side trim panels. (Figure B) 3. Remove (2) Phillips screws from radio trim panel. (Figure C) 4. Using panel removal tool, carefully remove radio trim panel. (Figure D) 5. Remove (4) 10mm bolts securing the radio. (Figure A) (Figure B) (Figure C) (Figure D) 6. Unplug and remove radio. 7.
PAGE 10
DASH DISASSEMBLY (CONT) Yaris 2007-2011 (without power package) 1. Unclip the bottom trim panel located underneath the A/C controls. (Figure A) 2. Unclip the two side trim panels that surround the A/C controls and radio. (Figure A) 3. Unclip the Instrument trim Panel surrounding the speedometer and gauges. (Figure B) 4. Unclip the radio/AC vents trim panel. (Figure B) 5. Remove (4) Phillips screws securing radio. (Figure C) 6. Unplug and remove radio. 7.
PAGE 11
DASH DISASSEMBLY (CONT) Yaris 2012-2017 Scion FR-S 2013-2014 1. Unclip and remove entire panel including A/C vent on passenger side of dash. (Figure A) 1. Unclip and remove the panel from around the radio. (Figure A) 2. Unclip and remove the panel from around the radio. (Figure B) 2. Remove four 10 mm bolts and remove factory radio. (Figure B) 3. Remove four 10 mm bolts and remove factory radio.
PAGE 12
DASH DISASSEMBLY (CONT) Scion iQ 2012-2015 1. Unclip and remove the climate control panel. (Figure A) 2. Unclip and remove the panel from around the radio. (Figure B) 3. Remove four 10 mm bolts and remove factory radio. (Figure C) Continue to Kit Preparation (Figure A) (Figure C) 12 (Figure B) 1.800.221.0932 | MetraOnline.
PAGE 13
DASH DISASSEMBLY (CONT) Scion xA 2004-2006 1. Pull outward on the (3) climate control knobs and remove. (Figure A) 2. Remove (2) Phillips screws from behind the outer two climate knobs. (Figure B) 3. Unsnap and remove the trim pieces on each side of the climate control/ashtray/pocket assembly. (Figure C) 4. Remove (2) Phillips screws from the bottom of the climate control/radio trim panel and unsnap and remove the entire panel. (Figure D) 5. Remove (4) Phillips screws to remove the factory radio. 6.
PAGE 14
DASH DISASSEMBLY (CONT) Scion xB 2004-2006 Scion xB 2008-2015 1. Pull outward on the (3) climate control knobs and remove. (Figure A) 1. Unclip and remove the trim panel around the radio including the A/C vents. (Figure A) 2. Remove (2) Phillips screws from behind the outer (2) knobs. (Figure B) 2. Unclip and remove the trim panel at the bottom edge of the dash cavity. (Figure B) 3. Unsnap and remove the entire panel surrounding the climate controls and the radio. (Figure C) 3.
PAGE 15
DASH DISASSEMBLY (CONT) Scion tC 2005-2010 Scion tC 2011-2016 1. Unsnap trim from around shifter (not necessary to be removed). (Figure A) 1. Unclip and remove the radio trim panel. (Figure A) 2. Unclip and remove panel from around radio (including climate controls and radio door). (Figure B) 2. Remove (4) 10mm bolts securing the radio. (Figure B) 3. Remove (2) 10mm nuts from the top mounting locations and (2) 10mm bolts from the bottom mounting locations to remove the radio. (Figure C) 3.
PAGE 16
DASH DISASSEMBLY (CONT) Scion xD 2008-2014 1. Unclip radio trim panel. Unplug and remove panel. (Figure A) 2. Remove (4) Phillips screws securing the radio. Unplug and remove radio. (Figure B) 3. Remove factory brackets from radio. Retain brackets for use during kit assembly. (Figure C) (Figure A) (Figure B) Continue to Kit Preparation (Figure C) 16 1.800.221.0932 | MetraOnline.
PAGE 17
DASH DISASSEMBLY Subaru BRZ 2013-2015 (CONT) Subaru Forester (with SD based navigation) 2009-2013 1. Unclip and remove the panel from around the radio. (Figure A) 1. Unclip and remove the trim panel surrounding the factory radio including the A/C vents. (Figure A) 2. Remove four 10 mm bolts and remove factory radio. (Figure B) 2. Remove (4) Phillips screws securing the radio. Unplug and remove the radio.
PAGE 18
KIT PREPARATION For the Scion tC (both generations) and xA: Cut off the front upper section of the ISO DDIN trim plate brackets, as shown by the dotted lines labeled “A” in. (Figure A) Continue to Kit Assembly For the Toyota Rav-4 2001-2005, Toyota Highlander 20012007 (without factory navigation), Toyota Tundra 2003-2006 and Toyota Sequoia 2003-2007: Cut off the rear section of the ISO DDIN trim plate brackets, as shown by the dotted lines labeled “B” in.
PAGE 19
KIT ASSEMBLY ISO DDIN radio provision 1. If applicable, remove the trim ring from the aftermarket radio. 2. Attach the factory mounting brackets and the ISO DDIN trim plate brackets to the radio with the screws supplied with the radio. Note: Remove locating pins from factory brackets using a grinder tool. 3. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Test the radio for proper operation. 4.
PAGE 20
95-8202 I N S TA L L AT I O N I N S T R U C T I O N S IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.
PAGE 21
95-8202 I N S T R U C C I O N E S D E I N S TA L AC I Ó N Toyota/Scion Multi-kit 2000-2017 INDICE Vea la página 2 CARACTERÍSTICAS DEL KIT • Provisión de radio ISO DDIN CABLEADO Y CONEXIONES DE ANTENA (se venden por separado) Arnés de cableado: Visite metraonline.com para las opciones de arnés de cableado Antenna Adapter: Visite metraonline.
PAGE 22
APLICACIONES Toyota Rav-4 MR2 Spyder Celica Echo Highlander (sin navegación de fábrica) Matrix Matrix (con navegación de fábrica) 4 Runner (excluyendo limited) Tundra Sequoia FJ Cruiser Yaris (sin unidad de alimentación) Yaris INDICE 2001-2005 2000-2005 2000-2005 2000-2005 2001-2007 2005-2008 2009-2010 2003-2009 2003-2006 2003-2007 2007-2014 2007-2011 2012-2017 Desmontaje del tablero – Toyota Rav4 2001-2005..............................................................3 – Scion xB 2008-2015..............
PAGE 23
DESMONTAJE DEL TABLERO Toyota Rav-4 2001-2005 Toyota MR2 Spyder 2000-2005 1. Desenganche y quite el panel lateral de ambos lados del radio y los controles del clima. (Figura A) 1. Desenganche la pieza de moldura inferior de cada lado de la consola del tablero y quite los (2) tornillos Phillips que quedan a la vista en cada cavidad. Quite la pieza de moldura superior de cada lado de la consola. (Figura A) 2. Quite los (4) tornillos Phillips que sujetan el panel de la moldura del radio/control de clima.
PAGE 24
DESMONTAJE DEL TABLERO (CONT) Toyota Celica 2000-2005 1. Desenganche y quite el bisel de la moldura 4. Quite los (4) tornillos de 10mm que de la palanca de velocidades y quite los (2) sujetan el radio de fábrica y desconecte el tornillos Phillips expuestos debajo de los cableado. controles del clima. (Figura A) 5. Quite los soportes de fábrica del radio. 2. Quite las perillas de control de clima y los Guarde los soportes para usarlos al (2) tornillos Phillips que quedan a la vista. ensamblar el kit.
PAGE 25
DESMONTAJE DEL TABLERO Toyota Highlander 2001-2007 (sin navegación de fábrica) 1. Jale y quite el panel del tablero del radio y los controles del clima. Sugerencia: Hay 8 ganchos. (Figura A) 2. Quite los (6) pernos de 10mm de los controles del radio y clima. (Figura B) Toyota Matrix 2005-2008 1. Desenganche el borde inferior del panel de la moldura del radio y luego levante y retire. (Figura A) 2. Quite los (4) pernos de 10mm que sujetan el radio de fábrica. (Figura B) (Figura A) 3.
PAGE 26
DESMONTAJE DEL TABLERO Toyota Matrix 2009-2010 (con navegación de fábrica) (CONT) Toyota 4-Runner 2003-2009 (excluyendo limited) 1. Desenganche el borde inferior del panel de la moldura del radio y luego levante y retire. (Figura A) 1. Suelte a presión y retire la moldura de alrededor de la palanca de velocidades. PASSENGER SECURITY 2. Suelte a presión y quite las tapas de la moldura de alrededor del borde de la cavidad de la consola central al frente y atrás de la consola. 2.
PAGE 27
DESMONTAJE DEL TABLERO Toyota 4-Runner 2003-2009 (Cont) (excluyendo limited) Toyota Tundra 2003-2006 1. Quite las (3) perillas de control de clima jalando directamente hacia el frente. (Figura A) 7. Quite (1) perno de 10mm de abajo del control de clima, detrás de la puerta de la cavidad. Suelte a presión y quite el control del clima. (Figura C) 2. Quite los (3) tornillos Phillips de atrás de las perillas. (Figura A) 8.
PAGE 28
DESMONTAJE DEL TABLERO Toyota Tundra 2003-2006 (Cont) 4. Desenganche y quite todo el panel de la moldura. (Figura C) 5. Quite los (4) pernos de 10mm para quitar el radio. (Figura D) 6. Desconecte y retire el radio. 7. Quite los soportes de fábrica del radio. Guarde los soportes para usarlos al ensamblar el kit. Continúe con la Preparación del Kit (Figura C) (CONT) Toyota Sequoia 2003-2007 1.
PAGE 29
DESMONTAJE DEL TABLERO (CONT) Toyota FJ Cruiser 2007-2014 1. Quite (2) tornillos Phillips de la parte de abajo de los paneles de la moldura lateral. (Figura A) 2. Con una herramienta de remoción de panel, quite con cuidado los paneles de la moldura lateral. (Figura B) 3. Quite los (2) tornillos Phillips del panel de la moldura del radio. (Figura C) 4. Con la herramienta de remoción de panel, quite con cuidado el panel de la moldura del radio.
PAGE 30
DESMONTAJE DEL TABLERO (CONT) Yaris 2007-2011 (sin unidad de alimentación) 1. Desenganche el panel de la moldura inferior localizado abajo de los controles de aire acondicionado. (Figura A) 2. Desenganche los dos paneles de la moldura lateral que rodean los controles de aire acondicionado y el radio. (Figura A) 3. Desenganche el panel de la moldura de instrumentos que rodea el velocímetro y los indicadores. (Figura B) 4. Desenganche el panel de la moldura del radio/las rejillas de aire acondicionado.
PAGE 31
DESMONTAJE DEL TABLERO Yaris 2012-2017 1. Desenganche y quite todo el panel, incluyendo la rejilla de aire acondicionado en el tablero del lado del pasajero. (Figura A) 2. Desenganche y quite el panel de alrededor del radio. (Figura B) 3. Quite los cuatro pernos de 10mm y quite el radio de fábrica. (Figura C) Continúe con la Preparación del Kit (CONT) Scion FR-S 2013-2014 1. Desenganche y quite el panel de alrededor del radio. (Figura A) 2. Quite los cuatro pernos de 10mm y quite el radio de fábrica.
PAGE 32
DESMONTAJE DEL TABLERO (CONT) Scion iQ 2012-2015 1. Desenganche y quite el panel del control del clima. (Figura A) 2. Desenganche y quite el panel de alrededor del radio. (Figura B) 3. Quite los cuatro pernos de 10mm y quite el radio de fábrica. (Figura C) Continúe con la Preparación del Kit (Figura A) (Figura C) 12 (Figura B) 1.800.221.0932 | MetraOnline.
PAGE 33
DESMONTAJE DEL TABLERO (CONT) Scion xA 2004-2006 1. Jale hacia afuera las (3) perillas de control de clima y quítelas. (Figura A) 2. Quite los (2) tornillos Phillips de la parte de atrás de las dos perillas exteriores del clima. (Figura B) 3. Suelte a presión y quite las piezas de moldura de cada lado del ensamble del control de clima/cenicero/bolsillo. (Figura C) 4.
PAGE 34
DESMONTAJE DEL TABLERO Scion xB 2004-2006 1. Jale hacia afuera las (3) perillas de control de clima y quítelas. (Figura A) 2. Quite los (2) tornillos Phillips de la parte de atrás de las perillas exteriores (2). (Figura B) 3. Suelte a presión y quite todo el panel que rodea el radio y los controles del clima y aire acondicionado. (Figura C) 4. Quite los (4) tornillos Phillips para quitar el radio de fábrica. 5. Quite los soportes de fábrica del radio.
PAGE 35
DESMONTAJE DEL TABLERO Scion tC 2005-2010 1. Suelte a presión la moldura que rodea la palanca de velocidades (no es necesario quitarla). (Figura A) 2. Desenganche y quite el panel que rodea el radio (incluyendo los controles del clima y la puerta del radio). (Figura B) 3. Quite (2) tuercas de 10mm de las ubicaciones superiores de montaje y (2) pernos de 10mm de las ubicaciones inferiores de montaje y quite el radio. (Figura C) 4. Quite los soportes de fábrica del radio.
PAGE 36
DESMONTAJE DEL TABLERO (CONT) Scion xD 2008-2014 1. Desenganche el panel de moldura del radio. Desconecte y retire el panel. (Figura A) 2. Retire los (4) tornillos Phillips que sostienen el radio. Desconecte y quite el radio. (Figura B) 3. Quite los soportes de fábrica del radio. Guarde los soportes para usarlos al ensamblar el kit. (Figura C) (Figura A) (Figura B) Continúe con la Preparación del Kit (Figura C) 16 1.800.221.0932 | MetraOnline.
PAGE 37
DESMONTAJE DEL TABLERO Subaru BRZ 2013-2015 (CONT) Subaru Forester (con navegación basada en SD) 2009-2013 1. Desenganche y quite el panel de alrededor del radio. (Figura A) 1. Desenganche y quite el panel de moldura que rodea el radio de fábrica, incluyendo las rejillas del aire acondicionado. (Figura A) 2. Quite los cuatro pernos de 10mm y quite el radio de fábrica. (Figura B) 2. Retire los (4) tornillos Phillips que sostienen el radio. Desconecte y quite el radio.
PAGE 38
PREPARACIÓN DEL KIT Para el Scion tC (ambas generaciones) y xA: Corte la sección delantera superior de las placas de moldura doble DIN como se muestra en las líneas punteadas rotuladas “A” en la . (Figura A) Continúe con Ensamble del kit Para Toyota Rav4 2001-2005, Toyota Highlander 2001-2007 (sin navegación de fábrica), Toyota Tundra 2003-2006 y Toyota Sequoia 2003-2007: Corte la sección trasera de las placas de moldura doble DIN como se muestra en las líneas punteadas rotuladas “B” en la.
PAGE 39
ENSAMBLE DEL KIT Provisión de radio ISO DDIN 1. Si aplica, retire el anillo de moldura del radio de mercado secundario. 2. Coloque los soportes de montaje de fábrica y las soportes de placas de moldura ISO DDIN al radio con los tornillos suministrados con la unidad. (Figura B) Nota: Quite las clavijas localizadoras de los soportes de fábrica con la rectificadora. 3. Ubique el arnés de cableado de fábrica en el tablero. Metra recomienda el uso de un adaptador adecuado de acoplamiento de Metra o de AXXESS.
PAGE 40
95-8202 I N S T R U C C I O N E S D E I N S TA L AC I Ó N IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.