User Manual

ManualsBrandsMetra ManualsAutomotiveMetra 95-8212 Double DIN Installation Kit for 2004-2008 Toyota Solara Vehicles (Silver)

METRA. The World’s best kits.

™

metraonline.com

REV. 10/28/2015 INST95-8212

Installation instructions for part 95-8212

CAUTION!

Metra recommends disconnecting the negative bat

tery terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your local

Dealership for more information. All accessories, switches, climate

controls panels, and especially air bag indicator lights must be con

nected before reconnecting the battery or cycling the ignition. Also,

do not remove the factory radio with the key in the on position, or the

vehicle running. It would be best to remove the key from the ignition

and then wait a few seconds before removing the factory radio.

• ISO DDIN radio provision

• A) Radio housing • B) ISO DDIN trim plate • C) ISO DDIN brackets

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • 70-1761 • TYTO-01

Antenna Adapter: • Not required

• Panel removal tool • Phillips screwdriver • 10mm socket wrench

TOOLS REQUIRED

Toyota Solara 2004-2008

95-8212

A B C

Dash Disassembly .............................................. 2-3

Kit Assembly

– ISO DDIN radio provision ...................................... 4

Table of Contents

Summary of content (8 pages)

PAGE 1
Installation instructions for part 95-8212 Toyota Solara 2004-2008 95-8212 Table of Contents Dash Disassembly............................................... 2-3 Kit Assembly –. ISO DDIN radio provision....................................... 4 KIT FEATURES • ISO DDIN radio provision KIT COMPONENTS • A) Radio housing • B) ISO DDIN trim plate • C) ISO DDIN brackets REV.
PAGE 2
95-8212 Dash Disassembly 1. Remove the cover from the hazard light switch, unclip the switch, and then unplug and remove it. (Figure A) 2. Unclip the panel above the radio including the a/c vents and clock, and then unplug and remove the panel. (Figure B) Note: Start pulling from the inside of the hazard switch cavity. 3. Unclip and remove the panel surrounding the shifter.
PAGE 3
95-8212 Dash Disassembly 4. Unclip and remove the pocket and seat heater switch panel. (Figure D) 5. Remove (4) 10mm screws securing the radio/climate control assembly, and then unplug and remove the assembly. (Figure E) 6. Remove (3) Phillips screws securing the climate controls to the factory brackets, and then remove the climate controls from the assembly. (Figure F, G) (Figure D) (Figure F) (Figure E) (Figure G) Note: Retain the climate controls and screws for reuse in kit assembly.
PAGE 4
Installation instructions for part 95-8212 Kit Assembly IMPORTANT ISO DDIN radio provision If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. 1.
PAGE 5
Instrucciones de instalación para la pieza 95-8212 Toyota Solara 2004-2008 95-8212 Indice Desmontaje tablero............................................. 2-3 Ensamble del kit –. Provisión de radio ISO DDIN.................................. 4 CARACTERÍSTICAS DEL KIT • Provisión de radio ISO DDIN COMPONENTES DEL KIT • A) Carcasa del radio • B) Placa de moldura ISO DDIN • C) Soportes ISO DDIN REV.
PAGE 6
95-8212 Desmontaje tablero 1. Retire la cubierta del interruptor de luces de emergencia, soltar el interruptor y desenchufe y quite. (Figura A) 2. Desenganche el panel de arriba del radio, incluyendo las rejillas y hora, y entonces desconecte y quite el panel. (Figura B) Nota: Comience tirando desde el interior de la cavidad interruptor de peligro. (Figura A) (Figura B) 3. Desenganche y quite el panel que rodea la palanca de velocidades.
PAGE 7
95-8212 Desmontaje tablero 4. Suelte y retire el canvidad y asiento del panel interruptor del calentador. (Figura D) 5. Quite los (4) tornillos de 10mm que sujetan el radio/conjunto de control climático, y luego desconecte y quite el ensamble. (Figura E) 6. Quite los (3) tornillos Phillips que sujetan el controles de clima en el soportes de fábrica y luego quite el controles de clima del conjunto.
PAGE 8
Instrucciones de instalación para la pieza 95-8212 Ensamble del kit IMPORTANTE Provisión de radio ISO DDIN Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar. 1.