User Manual

ManualsBrandsMetra ManualsAutomotiveMetra 95-8224 Double DIN Installation Dash Kit for 2009 Toyota Matrix and Pontiac Vibe

METRA. The World’s best kits.

™

metraonline.com

REV. 10/20/2015 INST95-8224

Installation instructions for part 95-8224

CAUTION!

Metra recommends disconnecting the negative bat

tery terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your local

Dealership for more information. All accessories, switches, climate

controls panels, and especially air bag indicator lights must be con

nected before reconnecting the battery or cycling the ignition. Also,

do not remove the factory radio with the key in the on position, or the

vehicle running. It would be best to remove the key from the ignition

and then wait a few seconds before removing the factory radio.

• ISO DDIN radio provision

• A) ISO DDIN trim plate • B) ISO DDIN brackets

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • 70-1761 (Matrix) • TYTO-01 (Matrix w/ amp) • 70-2105 (Vibe)

Antenna Adapter: • Not required (Matrix) • 40-CR10 (Vibe)

• Panel removal tool • 10mm socket wrench

TOOLS REQUIRED

Toyota Matrix 2009-10 / Pontiac Vibe 2009-10

(Excluding Factory Navigation Models)

95-8224

A B

Dash Disassembly ..................................................2

Kit Preparation ........................................................ 2

Kit Assembly

– ISO DDIN radio provision ...................................... 3

Table of Contents

Summary of content (8 pages)

PAGE 1
Installation instructions for part 95-8224 Toyota Matrix 2009-10 / Pontiac Vibe 2009-10 Table of Contents (Excluding Factory Navigation Models) Dash Disassembly...................................................2 95-8224 Kit Preparation.........................................................2 Kit Assembly –. ISO DDIN radio provision....................................... 3 KIT FEATURES • ISO DDIN radio provision KIT COMPONENTS • A) ISO DDIN trim plate • B) ISO DDIN brackets REV.
PAGE 2
95-8224 Dash Disassembly Kit Preparation 1. Unclip and remove the radio trim panel, including the a/c vent. (Figure A) 1. Snap the ISO DDIN trim plate into the rear of the factory radio trim panel. (Figure A) PASSENGER 2. Remove (4) 10mm screws securing the radio, then unplug and remove.
PAGE 3
95-8224 Kit Assembly ISO DDIN radio provision 1. Attach the ISO DDIN brackets to the radio using the screws supplied with the radio. (Figure A) 2. Locate the factory wiring harness and antenna adapter in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the radio for proper operation. 3. Reassemble the dash in reverse order of disassembly.
PAGE 4
Installation instructions for part 95-8224 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. KNOWLEDGE IS POWER REV.
PAGE 5
Instrucciones de instalación para la pieza 95-8224 Indice Toyota Matrix 2009-10 / Pontiac Vibe 2009-10 (excluyendo los modelos de navegación de fábrica) Desmontaje tablero.................................................2 95-8224 Preparación del kit..................................................2 Ensamble del kit –. Provisión de radio ISO DDIN..................................
PAGE 6
95-8224 Desmontaje tablero 1. Desenganche y quite el panel de la moldura del radio, incluyendo las rejillas del aire acondicionado. (Figura A) Preparación del kit 1. Coloque a presión la placa de moldura ISO DDIN en la posterior del panel de moldura de radio de fábrica. (Figura A) PASSENGER SECURITY 2. Quite los (4) tornillos de 10 mm que sujetan el radio, y luego desconecte y quite.
PAGE 7
95-8224 Ensamble del kit Provisión de radio ISO DDIN 1. Coloque los soportes ISO DDIN en el radio con los tornillos que vienen con el radio. (Figura A) 2. Localice el arnés de cableado de fábrica y el conector de la antena en el tablero. Metra recomienda que use adaptadores adecuados de acoplamiento de Metra y/o de AXXESS. Vuelva a conectar la terminal negativa de la batería y pruebe el radio para verificar que funcione correctamente. 3. Vuelva a armar el tablero al revés de como lo desarmó.
PAGE 8
Instrucciones de instalación para la pieza 95-8224 IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.