User Manual

ManualsBrandsMetra ManualsAutomotiveMetra 95-8905B Double DIN Dash Installation Kit for Select 2012-Up Subaru Impreza Vehicles (Black)

METRA. The World’s best kits.

™

metraonline.com

REV. 8/7/2015 INST95-8905B

Installation instructions for part 95-8905B

CAUTION!

Metra recommends disconnecting the negative bat

tery terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your local

Dealership for more information. All accessories, switches, climate

controls panels, and especially air bag indicator lights must be con

nected before reconnecting the battery or cycling the ignition. Also,

do not remove the factory radio with the key in the on position, or the

vehicle running. It would be best to remove the key from the ignition

and then wait a few seconds before removing the factory radio.

• ISO DDIN radio provision

• Painted Matte Black

• A) Radio trim panel • B) Radio brackets

KIT FEATURES

KIT COMPONENTS

Subaru 2012-2015

95-8905B

Table of Contents

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • 70-7552

Antenna Adapter: • Not required

• Panel removal tool • Phillips screwdriver

• Small Flat Blade Screwdriver

TOOLS REQUIRED

APPLICATIONS

Dash Disassembly ................................................. 2

Kit Assembly

– ISO DDIN radio provision ...................................... 3

Forester (without NAV) 2014-2015

Impreza

(without NAV) 2012-2014

WRX (without NAV) 2015

XV Crosstrek

(without NAV) 2013-2014

SUBARU

Summary of content (8 pages)

PAGE 1
Installation instructions for part 95-8905B Table of Contents Subaru 2012-2015 95-8905B Dash Disassembly.................................................. 2 Kit Assembly –. ISO DDIN radio provision....................................... 3 KIT FEATURES • ISO DDIN radio provision • Painted Matte Black TOOLS REQUIRED • Panel removal tool • Phillips screwdriver • Small Flat Blade Screwdriver KIT COMPONENTS • A) Radio trim panel • B) Radio brackets REV.
PAGE 2
95-8905B Dash Disassembly 1. Disconnect the air selector cable located on the driver’s side of the center console, behind the dash and above the gas pedal. (Figures A and B) 4. Unclip and remove the trim panel surrounding the factory radio including the a/c vents and climate controls. (Figure D) 5. Remove (4) Phillips screws from the factory radio and remove. (Figure E) 2. Open the glove box and squeeze in on the sides to remove it. 3.
PAGE 3
95-8905B Kit Assembly ISO DDIN radio provision 1. Attach the radio brackets to the radio trim panel. (Figure A) 2. Attach the radio to the completed assembly using screws supplied with the radio. (Figure B) 3. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or AXXESS. Re-connect the negative battery terminal and test the radio for proper operation.
PAGE 4
Installation instructions for part 95-8905B IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. KNOWLEDGE IS POWER REV.
PAGE 5
Instrucciones de instalación para la pieza 95-8905B Indice Subaru 2012-2015 95-8905B Desmontaje del tablero.......................................... 2 Ensamble del kit –. Provisión de radio ISO DDIN..................................
PAGE 6
95-8905B Desmontaje del tablero 1. Desconecte el cable selector de aire del lado del conductor de la consola central detrás del tablero sobre el pedal del acelerador. (Figuras A & B) 4. Desenganche y quite el panel de moldura que rodea el radio de fábrica, incluyendo las rejillas del aire acondicionado y los controles de clima. (Figura D) 2. Abra la guantera y apretar en en los laterales para extraerla. 5. Retirar (4) tornillos Phillips de la radio de fábrica y retirar. (Figura E) 3.
PAGE 7
95-8905B Ensamble del kit Provisión de radio ISO DDIN 1. Fije los soportes de Radio en el Panel de ajuste de Radio. (Figura A) 2. Conecte la radio al conjunto completo con los tornillos suministrados con la radio. (Figura B) 3. Localice el arnés de cableado de fábrica y el conector de la antena en el tablero y haga todas las conexiones necesarias al radio. Metra recomienda que use adaptadores adecuados de acoplamiento de Metra y/o de AXXESS.
PAGE 8
Instrucciones de instalación para la pieza 95-8905B IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.