Instructions

ManualsBrandsMetra ManualsAudioMetra Kia Rio/Rio5 2012-2015 Radio Provision

METRA. The World’s best kits.

™

metraonline.com

REV. 7/29/2015 INST95-7353CH

Installation instructions for part 95-7353CH

CAUTION!

Metra recommends disconnecting the negative bat

tery terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your local

Dealership for more information. All accessories, switches, climate

controls panels, and especially air bag indicator lights must be con

nected before reconnecting the battery or cycling the ignition. Also,

do not remove the factory radio with the key in the on position, or the

vehicle running. It would be best to remove the key from the ignition

and then wait a few seconds before removing the factory radio.

• ISO DDIN radio provision

• Painted Charcoal

• A) Radio housing trim panel • B) Radio brackets • C) Start/Stop switch blank plate

• D) Airbag light blank plate • E) (5) #8 x 3/8” Phillips truss-head screws

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • 70-7304

Antenna Adapter: • Not required

• Panel removal tool • Phillips screwdriver • Socket wrench

TOOLS REQUIRED

Kia Rio, Rio5 2012-2015

95-7353CH

Dash Disassembly ................................................. 2

Kit Preparation ....................................................... 3

Kit Assembly

– ISO DDIN radio provision ...................................... 3

Table of Contents

B C D E

Summary of content (8 pages)

PAGE 1
Installation instructions for part 95-7353CH Table of Contents Kia Rio, Rio5 2012-2015 95-7353CH Dash Disassembly.................................................. 2 Kit Preparation........................................................ 3 Kit Assembly KIT FEATURES • ISO DDIN radio provision • Painted Charcoal –. ISO DDIN radio provision.......................................
PAGE 2
95-7353CH Dash Disassembly 1. Unclip and remove the factory radio trim panel including the a/c vents. (Figure A) Note: Remove the (8) retaining clips to be reused in Kit Assembly. 2. Remove (4) Phillips screws securing the radio in the dash. 3. Remove (2) Phillips screws securing the start/stop switch if equipped. (Figure B) 4. Remove (4) Phillips screws securing the storage pocket (Figure B) 5. Remove the (8) Phillips screws securing the a/c vents then unclip and remove them from the radio trim panel.
PAGE 3
95-7353CH Kit Preparation 1. Mount the a/c vents, storage pocket, hazard switch, and passenger air bag indicator into the Radio Housing Trim Panel using screws removed in disassembly. (Figure A) Note: For models without an airbag light, a blank plate and (3) #8 x 3/8” Phillips Truss-Head Screws are provided. Kit Assembly Note: If no switch is present there are (2) #8 X 3/8” Phillips truss head screws supplied to mount the blank plate. ISO DDIN radio provision 1.
PAGE 4
Installation instructions for part 95-7353CH IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. KNOWLEDGE IS POWER REV.
PAGE 5
Instrucciones de instalación para 95-7353CH Indice Kia Rio, Rio5 2012-2015 95-7353CH Desmontaje del tablero.......................................... 2 Preparación del kit................................................. 3 Ensamble del kit CARACTERÍSTICAS DEL KIT • Provisión de radio ISO DDIN • Carbón pintado –. Provisión de radio ISO DDIN..................................
PAGE 6
95-7353CH Desmontaje del tablero 1. Desenganche y quite el panel de la moldura del radio de fábrica, incluyendo las rejillas del aire acondicionado. (Figura A) Nota: Quite los ganchos de retención (8) para ser reutilizado en ensamble del kit. 2. Quite los (4) tornillos Phillips que sostienen el radio en el tablero. 3. Quite los (2) tornillos Phillips que sostienen el interruptor de inicio/paro si se incluye. (Figura B) 4. Quite los (4) tornillos Phillips que sostienen la cavidad de almacenamiento.
PAGE 7
95-7353CH Preparación del kit 1. Monte los respiraderos de aire acondicionado, bolsillo, interruptor de peligro e indicador de airbag de pasajero en la vivienda Trim Panel de Radio utilizando tornillos que quitó en el desmontaje. (Figura A) Nota: Para modelos sin una luz de airbag, una placa en blanco y (3) #8 x 3/8” tornillos Phillips de cabeza del braguero se proporcionan. 2.
PAGE 8
Instrucciones de instalación para 95-7353CH IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.